PSU, 5pin DIN connector for grip, fan, jst connectors... https://github.com/protomaker964/Rhino-FFB-

PSU, 5pin DIN connector for grip, fan, jst connectors...
https://github.com/protomaker964/Rhino-FFB-Clone-3D_Printed/tree/main

GitHub

GitHub - protomaker964/Rhino-FFB-Clone-3D_Printed: 3D print files, ...

3D print files, parts list and instructions to build a DIY version of the Rhino FFB Stick base using the VPForce motor kit - GitHub - protomaker964/Rhino-FFB-Clone-3D_Printed: 3D print files, parts...

SubsonicOP•10/26/23, 4:18 AM

parts list in the build pdf

SSubsonic So....crazy thing I have seen sine the last DCS update.... Tomcat on deck before...

walmis•10/26/23, 4:46 AM

Do you have telem running? Can you check the fault code once it enters the failed state?

SSubsonic PSU, 5pin DIN connector for grip, fan, jst connectors... https://github.com/prot...

A. Palmetto•10/26/23, 5:16 AM

Thank you! I’m actually looking to use this print! I posted a question about the pullys in the DIY channel I figure it would be a better channel than a support channel for the actual rhino

Wwalmis Do you have telem running? Can you check the fault code once it enters the faile...

SubsonicOP•10/26/23, 12:28 PM

Dang, forgot about telem, I will give that a look today. Thanks!

blave549•10/26/23, 5:27 PM

Just a note that I ran into something that I'd never seen before in DCS Open Beta (that is almost certainly unrelated to anything Rhino). In the A-10C II, my stick would not work, even though the x/y axes showed up as working in the Control Options dialog. At one point it started working, but then stopped again. I think, but am not sure, that it's specific to the Hawg. I tried a couple other aircraft and they were fine.

Wwalmis Do you have telem running? Can you check the fault code once it enters the faile...

SubsonicOP•10/27/23, 1:39 PM

Good morning (afternoon for you I think),
SO I ran Telem and did some testing.
When I can induce the shutdown, nothing shows in telemetry.
So I messed around with the max gain pot and lowered it some and no pitch shutdown on faster pulls.
Certainly seems related to effect intensity and just the pitch motor shutting down.
Do you think this is maybe power supply related? I was thinking not since the roll motor stays active.
Could this be a motor current issue and will the max current setting in the software help? Though it is set to 25A and the PSU is not gonna push that much.
Keeping max gain turn down a bit seems to keep it all in check, but I would love to get back to the strength settings I had if possible.
Thanks!

SSubsonic Good morning (afternoon for you I think), SO I ran Telem and did some testing. W...

walmis•10/27/23, 1:44 PM

A motor fault code would be useful here, it's displayed in the status bar (OK when operational)

SubsonicOP•10/27/23, 1:50 PM

ahh in the status bar ok...since in the main telem screen I saw nothing but the normal connections ok, effects on, and the power reset.
In this status bar?

SubsonicOP•10/27/23, 1:50 PM

walmis•10/27/23, 2:04 PM

No, at the bottom:

walmis•10/27/23, 2:04 PM

It will show a fault code if the motor shuts down with a long beep

SubsonicOP•10/27/23, 2:06 PM

Got it thanks

Timmy•10/27/23, 2:18 PM

If I set the pot function as Spring Gain, does it mean that at 100% pot value the spring effect would be at 30% according to the settings below?

smitty•10/27/23, 2:26 PM

yep the knob goes to that max setting

Snooper•10/27/23, 3:38 PM

hello, why in msfs flying th a2a comanche, I'm seeing the yoke moving but that is not reproduced in the rhino?

smitty•10/27/23, 3:47 PM

what kind of movement are you seeing? is this with or without autopilot

SSnooper hello, why in msfs flying th a2a comanche, I'm seeing the yoke moving but that ...

Number481•10/27/23, 4:09 PM

You gotta give us more info.. Are you using TelemFFB? Are you using the latest version which adds trim/AP following support? Have you set up the trim/ap following per the TelemFFB section in the VPforce manual?

Snooper•10/27/23, 5:03 PM

yes yes and yes

Snooper•10/27/23, 5:04 PM

I have it this way:

Snooper•10/27/23, 5:04 PM

#############################
##### MSFS Specific Defaults
#############################
telemffb_controls_axes = True
trim_following = True
ap_following = True

Snooper•10/27/23, 5:04 PM

in the config.ini

SSnooper yes yes and yes

Number481•10/27/23, 5:11 PM

Another quite important question... Do you have 'sticky spring' enabled in VPf Configurator?

Snooper•10/27/23, 5:19 PM

let me check

Snooper•10/27/23, 5:19 PM

Snooper•10/27/23, 5:20 PM

SSnooper no

Number481•10/27/23, 5:25 PM

Did you unbind your axes in MSFS? Sorry.. just going through the common issue causes

Snooper•10/27/23, 5:26 PM

yes I did

Snooper•10/27/23, 5:27 PM

I felt like it was for nothing, but I did. or felt like I did it someway wrong

Snooper•10/27/23, 5:27 PM

just cleared the bind and assign it back again as it was..

Number481•10/27/23, 5:29 PM

what does your comanche settings look like in your telemffb config?

Number481•10/27/23, 5:30 PM

last thing would be to drop a copy of your TelemFFB log file in here for me to look at.

Snooper•10/27/23, 5:30 PM

I think I have nothing specific for it

Snooper•10/27/23, 5:31 PM

config.ini24.32KB

Snooper•10/27/23, 5:33 PM

if you have some specific for the comanche that would be awesome

Snooper•10/27/23, 5:33 PM

and thanks!!

SSnooper Click to see attachment

Number481•10/27/23, 5:35 PM

This looks like maybe an old copy of the default config.ini? The default for the latest TelemFFB has the a2a pa-24 (comanche) in it already

Number481•10/27/23, 5:36 PM

Without a specific aircraft section telling TelemFFB that the aircraft is a "PropellerAircraft".. things won't work right.

Snooper•10/27/23, 5:36 PM

ok.. all update and check if it has the comanche config part

Number481•10/27/23, 5:37 PM

your telemFFB log would tell me alot too

NNumber481 Did you unbind your axes in MSFS? Sorry.. just going through the common issue ...

Snooper•10/27/23, 5:58 PM

so, I need to unbind it a leave it unbind right?

SSnooper so, I need to unbind it a leave it unbind right?

Number481•10/27/23, 5:59 PM

yeah.. in order to get around the way MSFS behaves.... TelemFFB has to be the source of the axis position for the trim following feature to work.

Snooper•10/27/23, 6:03 PM

so I think I did all things right, and I have all set to true and unbinded the axis and im getting them to move in the sim

Snooper•10/27/23, 6:04 PM

but I put power to the ap and watch the yoke move in the sim but I dont see it in the rhino

Number481•10/27/23, 6:06 PM

telemffb log please

Snooper•10/27/23, 6:07 PM

ps im testing in the ground

Snooper•10/27/23, 6:08 PM

TelemFFB_ffff-2055_config.ini_config.user.ini.log13.86KB

Snooper•10/27/23, 6:13 PM

but the yoke moves it should move in the rhino too

Snooper•10/27/23, 6:29 PM

changing the hdg bug I can see in the msfs the yoke move and in the TelemFFB I see the ailerondefl move but not physicaly in the rhino

SSnooper but the yoke moves it should move in the rhino too

Number481•10/27/23, 6:31 PM

remember that MSFS has zero FFB implementation.. so all of the FFB is done through TelemFFB. This trim/AP following was not super simple to implement and is relatively new and while I promise it does in fact work, I certainly havent figured out all of the ways it can be mis-configured yet.. thats why I'm asking the stupid obvious questions.

PSU, 5pin DIN connector for grip, fan, jst connectors... https://github.com/protomaker964/Rhino-FFB-

Similar Threads

Similar Threads

Similar Threads