I can't get Edge to stop it either... then the notifications get 'stuck' and the only way to get the
I can't get Edge to stop it either... then the notifications get 'stuck' and the only way to get them to go away is to kill all the edge processes
Achrome does it too lol, so i get double
Abut none of my other controllers have this problem, i assuming it's something related to a webusb api?
Ayeah, if i forget to close it, it seems to get stuck heh, and with an ultrawide, it's something that can sometimes be missed lol
NOnly have Edge and Brave (my default).. Brave will popup if you plug/replug.. but it goes away by itself or you can close it.. edge is a PITA and I think their WebUSB is messed up
Auninstalling the browsers isn't something i can really do given my line of work/job
NI did find some documentation on hard-disabling WebUSB in Edge via GPO but never went very far down that path 
WThere's a chrome flag that might help:
Nedge seems to ignore that (I have it disabled)
Aoh sick, will def shut this off in chrome
Ai'll try both of these! much appreciated!
Adoing this in chrome and edge appears to have fixed the problem! thanks!
Shi, with the new version and after testing, the engine rumble makes the rhino rumble a lot making it disconnect the X axis as before. but I noticed that if I cut the engine the effect goes away in the TelemFFB but the rhino keeps rumble. any idea? I'll turn it down at low RPM and check. if not I have to turn it off for now
Nit is unlikely that any of the rumble effects are causing your axes to go into protection mode and disconnect. If your screenshot above 🧰support is still accurate, you have the "Periodic Effects LPF" set to 0Hz.. I can't give you a technical explanation, but I can tell you that that will not play nicely with the effects in TelemFFB. The default is 20Hz I believe
WOh yea, didn't notice that! 0Hz on periodic will definitely cause problems, set it to 20Hz @snooperoldschool
Sok, if I changed it it was by mistake because I dont recall messing with that!!!
SI'm positive sure that I didn't change that!
Sthanks!
WNo prob, maybe a firmware update caused it, who knows 
Sthats was the culprit, problem solved, now i runs like a kitten, so much I need to put more intensity in the low rpm rumble lol
Sbut I have something here
Sif I cut the engine I get all rumbling again until it disconnects.
SIf I set engine_rumble_lowrpm_intensity = 0.2 after cut the engine have the same behavior .
Ncut the engine on the ground or cut the engine in the air?
Sall in the ground
Sand the only thing that solves it is disconnect and connect again
Sthe behavior dont shows at 0.1
SI have to do more testing, i'll report back.
Nwhat is your
engine_rumble_lowrpmit happened at 0.2
Sand actually after the engine cut the effects go out in the app but the rhino keeps shaking
Si'll make a video , its better to see it instead of write it up, because it looks something more is happening in the background.
WDoes the telemFFB log indicate any errors? Sounds like USB could be picking up interference or smth.
Sthe only error is after some seconds the beep and the X axis disconnect with that previous error.
Wahh, try reducing the the LPF from 20Hz to 15Hz
Sits like its getting stronger with each start I do
SMotor X: FAULT_UNEXPECTED_D_CURRENT
S
Schanging from 20 to 15hz look that helped somehow but just to mitigate it
Swhat I'm doing is start the engine and stop it several times
Si'll record it
WWhat happens here when you do it?
Swhere is that?
WDebug tab
Sone sec
S
Sfirst start
Wcan you scroll loaded effects to the bottom?
Salready heppned it disconnected the X
S
Sand with it working
