Thanks 481, do I need to copy over my user ini file to the downloads location? then delete the other
Thanks 481, do I need to copy over my user ini file to the downloads location? then delete the other?
Nsuggest just creating a "VPForce-TelemFFB" folder somewhere and moving the contents of the folder in your downloads directory to it. You can place your config.user.ini file in the directory with the new version. It will offer to import the settings into the new config structure (see 4.2.1.2 in the manual).
MOK, have done all that. I have 3 different vpconf files, for different modules (F14, F5 and F18) To enable automatic running of each when I use that module, I went to System/Edit Sim class defaults 7 offline models. I then in the 3rd column dropdown selected all the F14 variants there ( there are 3..?) and scrolled to the bottom to configurator file. I checked this box, then I highlighted the line and used the browse button to navigate to the location of the saved config files ( in my case in "configs" in my main VPforce configurator file location) . On selection, I was returned to the GUI, but there was no where I could see that link was made. Was that the correct procedure for linking a profile to a particular module? Assuming that is correct, I can then in the same GUI edit the Telem FFB effects for that module to differing values using the slider after highlighting each one....correct?
MFinal query ( I hope!) Some of the configs I mentioned aboved were from a buddy. He has some quite different values in the "expert settings" section. I enclose a picture of mine, which I think ( was a while ago now) Walmis recommended. Could I ask that someone take a look at my values and tell me if they are correct? And if not what changes you would recommend and why. many thanks
MI ask as these are different from those in the default config as well as those of my buddy.
NIn the defaults/class editor, after browsing for the file you need to hit the "update value" button, at which point you will see the value updated in the table...
The process is the same for editing any value via that interface.
The process is the same for editing any value via that interface.
Nyou can also make changes while you are loaded in the aircraft via the settings tab in TelemFFB. However, you are limited to the active aircraft here
MThanks, thats clear for using telemFFB effects. What about changing configs in the main VPforce config app for module specific ?I just ran DCS and used the F14, but it did not change the profile being used by vP force config from the default one I had loaded. I used the process as described above.....
Mif you have 5 minutes, it may be quicker and easier if we jumped in the voice channel?
Msave all the pesky typing...!
Ntied up for another hour or so but can after that
Mgreat, thanks will ping you in an hour
A@walmis any idea on how that’d work out?
MJust to be 100% clear here as well, I am talking about automatically changing config files to match the aircraft you are flying in VPForce config, NOT the per module settings for the TelemFFB effects.
Nworks the same way... free now if you want to jump in voice channel
Mcool, gimme 2 minutes willl be there
NI've tried 3 different mics on 2 different devices.. issue must be in between or on your side
WIt would work technically, but I'm not sure about the mechanical connection. If the Z extension has a free cable i.e. not a rigid connector then it would be not a problem, otherwise it would be easy to break the WW adapter. In other words if you could mount a TM grip on the Z extension it should be good to go.
MI use a Rhino with virpil Z extension and a hobby built grip with a thrustmaster type mount, it all works fine.
AFor those of you with a winwing grip on your rhino and still using simapp pro will you please DM me and tell me how you got it to work please? 
Fto my knowlede simapp pro does not work with the rhino winwing grip adapter. That communication relies on the "orion" base to work.
Sis it normal that if i import default config my rhino is out of center for like 3 degrees to the right? and if i put endstops afther default apply the endstops are more to the right
AAh I see, thank you.
Si dont know for sure but with those settings my vpforce is going bbbbrrrrrtttt en motor shuting down, those are profile settings for heli that i got from profile sharing, am i doing somthing wrong? or is my vpforce.... 
TTry ditching Friction and Inertia for a start.
WTry damper and spring LPF settings 2Hz and 4Hz respectively
PI think you need to turn down the Friction & intertia LPF Hz. NVM 
why didn't I see the two answers above me? lol
why didn't I see the two answers above me? lolSSo Is it like a lotto ticket for stable motors? Because this are settings from profile share... I really love the vpforce, it's a beast 
but i try to understand why i can not use 3 out of 5 profile share settings
but i try to understand why i can not use 3 out of 5 profile share settingsPI wonder that about the different settings some ppl have compared to others too. It also seems to me that my x axis motor will be the one to shudder & cut out more than the y axis when I experiment with setting changes.
MHow do you edit and save values in an existing vpconf file? I have edited some values in some of mine and they appear to get saved to devices memory when you press store and apply, rather than the actual vpconf file. So when I fly the module again, it automatically loads the previous unedited version. Thanks
WYou need to export the settings into a file again
M
Shi, i got my rhino diy build. the axis are shown, but the grip will not work. I tried Thrustmater Warthog Grip and a Virpil grip. I measured the pins from Connector to connector, all cables are Ok.
WAre you 100% sure the pinout is correct?
Syeah, i found the failure the wrong stick was configured. sorry 
FI assume grip matters a lot, mine is like 2x as heavy as its plastic variant
Bi submitted a pre-order from on the 11th of feb. when i run the info command with my email address i get "The application did not respond" Is the app down or is my pre-order not in the system yet?
BCan you confirm which grip type I should select?
CHello, very much enjoying my Rhino. Have noticed some clicking when pushing against it even with fairly gentle pressure. I can record a video to document this if needed. It seems mechanical.
AI had some clicks/clunks when moving against spring forces. Also a slight nudge could be felt on the stick. Eneded up being the bolts on the big pulleys. I tightened each by 1/8 turn and it's better now.
Cthank you, are those the ones that hold in the belts on the outside?
AYou're welcome. Yep, five bolts on each pulley. Hopefully it's that simple and not something else.
LHello has anyone a good recomendation for whear to metall 3d printing the Joystick mount
WYou can try again
SHey all - building my own DIY Rhino and have got to the point where i need to order steppers and USB interface. Any advice on which ones to go for?
TIf you are building from the files that are getting shared here, most, if not all, of them are only designed for the 57 series motors. The big motors won’t fit the same housing.
SPerfect! Thanks @TheAmazinGreat. Final thing, The Thrustmaster warthog grip works as standard doesnt it? I dont need an adapter or anything?
MNo adapter needed.
SThanks!
BNevermind, it must have been a bad connection in my extension. I took everything apart to make sure I didn't have any bent pins, and it works now after putting everything back together. Weird that the grip was getting power, but buttons weren't registering on the Rhino, but all is well now.
BHi, i need some help with the A2A Comanche. I can't get autopilot following to work, did some searching in this channel but found no solutions. The TelemFFB software is running fine otherwise, all the effects are working, axis are not bound in MSFS.