WH grip is M36x2.0 Correct on the 5 pin to JST XH. My kit came with all the connectors other than

WH grip is M36x2.0

Correct on the 5 pin to JST XH.

My kit came with all the connectors other than the JST ones for the peripherals. If your kit didn’t come with the motor leads maybe Walmis could help.

TheAmazinGreatOP•3/20/24, 3:40 PM

🧰support
Grip pinout

TTheAmazinGreat WH grip is M36x2.0 Correct on the 5 pin to JST XH. My kit came with all the co...

BAKE•3/20/24, 3:42 PM

Thanks.
I found the Pinout (I think)

Given that Walmis is super busy, and my order was 2 years ago, I'm thinking my complaint period has closed.
Its just a couple of connectors after all.
If I cant find them, I'll likely solder on some Xt30s or something similar.

BAKE•3/20/24, 3:48 PM

Im not sure this pin out matches what @TheAmazinGreat linked..

TheAmazinGreatOP•3/20/24, 3:48 PM

Another one that is a bit easier to read

Number481•3/20/24, 3:49 PM

The one amazing great posted, along with this one helped it make sense to me when I was doing my cable : 🧰support

TheAmazinGreatOP•3/20/24, 3:50 PM

The one I linked is the “male” side. The other one pictured can be a bit deceiving because of the pin numbering in the table since it is out of order numerically on the table but in somewhat of a numerical order on the picture.

TTheAmazinGreat The one I linked is the “male” side. The other one pictured can be a bit deceivi...

BAKE•3/20/24, 3:56 PM

Will the 6pin PS/2 cable work fine?

BBAKE Will the 6pin PS/2 cable work fine?

TheAmazinGreatOP•3/20/24, 4:07 PM

You might be able to make it work by modifying since the nub in the middle is different between the two. I just got some off digikey, might be able to get those NS39 connectors there too.

BAKE•3/20/24, 5:07 PM

I ordered some 6 pin female panel connectors, I found a datasheet drawing of the 5s and 6s connectors. The difference is very minor.

Pretty sure I have the XH connectors in my RC stuff.

Xt30s to change out the motor power connectors. Since i have the 86 size motors. and a 300w PS.
Ordered 20amp resettable breaker,

What else....

BAKE•3/21/24, 1:08 AM

@walmis
i have a single motor connected on the bench, and It looks like VPForce doesnt recognize its connected.

BAKE•3/21/24, 1:10 AM

Do I have my connections right?

Number481•3/21/24, 1:10 AM

disable the axis thats not connected

NNumber481 disable the axis thats not connected

BAKE•3/21/24, 1:11 AM

iv tried disabling each axis one at a time. no luck.
it says in bottom right i have no motors connected

Number481•3/21/24, 1:17 AM

yea, I see that now.... if you've verified the motor is getting power, I'm not sure what else to look at. The wiring isn't complex and looks right to me.

BAKE•3/21/24, 1:17 AM

ill dbl chk power

ju_caesar•3/21/24, 1:19 AM

I am not 100% sure but I think I saw someone with a similar problem some time ago and I believe it was that the motors are labeled X or Y and have to be plugged in as such into the M/B.

BAKE•3/21/24, 1:35 AM

looks like power issue, though i dont know what could have happened between last night and today to make it not work anymore

Number481•3/21/24, 1:38 AM

IIRC, there’s a green LED on the motor in the cavity where the connectors are. But I’m not sure if it’s just a power indicator or a board communication status indicator.

nz aviator•3/21/24, 2:13 AM

anyone had issues with the xplane 12 zibo 737 with control jitter while running telemffb?

BAKE•3/21/24, 2:14 AM

Would this explain my power supply not working?

Nnz aviator anyone had issues with the xplane 12 zibo 737 with control jitter while running ...

Number481•3/21/24, 3:05 AM

you are very likely the first person to try, to be honest. What you describe sounds like the axis position that TelemFFB is sending is fighting with what X-Plane is reading. The xplane plugin for TelemFFB sends the commands to override the axes, but there is a lot of unknown about how different 3rd party modules are implemented in xplane. Even the default R22 helicopter doesn't listen to the override command for the collective axis. It is entirely possible that many of the more advanced 3rd party aircraft won't work.

You can try disabling the axis control in TelemFFB and see if it clears up (this will also disable any trim/autopilot following). You can also try un-binding the axes in X-Plane.

NNumber481 you are very likely the first person to try, to be honest. What you describe so...

nz aviator•3/21/24, 3:46 AM

axis control was definatly the issue thankfully still useable without.\

hellfudge•3/21/24, 11:31 AM

Please help, I’m not getting any ffb on il2.

hellfudge•3/21/24, 11:32 AM

This is from rhino debug log

Hhellfudge This is from rhino debug log

Number481•3/21/24, 11:58 AM

explain more what you mean. There is nothing abnormal in that debug tab output

hellfudge•3/21/24, 12:03 PM

Well I hoped it would work out of the box. I checked that ffb was enabled and everything else is default. In game I only have the rhino spring feeling, no ffb, rumble etc

Number481•3/21/24, 12:08 PM

the native FFB in IL2 is limited to:

Dynamic spring force based on airspeed
ground bumps
gunfire
stall buffeting

In the latest IL2 versions, the stall buffeting is extremely weak in my experience

Fresh_Mint•3/21/24, 12:10 PM

Did you use the TelemFFB?

Number481•3/21/24, 12:15 PM

telemffb only adds supplemental and alternative (to the three I mentioned) effects. The actual 'FFB' (dynamic stick forces, trim following) are %100 handled by the game.

hellfudge•3/21/24, 12:16 PM

No telemffb, but it is not required right?

hellfudge•3/21/24, 12:18 PM

Do I need to enable the effects in rhino to be overrided by the game?

Number481•3/21/24, 12:22 PM

post screenshots of your configurator effects and settings tab (win+shif+s for windows snip tool is your friend, vs pictures with your phone)

hellfudge•3/21/24, 12:26 PM

Yes I know I’m on a new setup and did not have Discord app installed yet

hellfudge•3/21/24, 1:06 PM

Ok there are ffb effects but they’re so weak it’s barely noticeable. 85% periodic effects and the stick barely vibrates when shooting. I guess I just need to crank everything to the max

Hhellfudge Ok there are ffb effects but they’re so weak it’s barely noticeable. 85% periodi...

Number481•3/21/24, 1:19 PM

check the "shake" slider in the IL2 FFB settings. It defaults to max, I believe, but just in case... Also your Periodic LPF value in the configurator expert settings will have an impact (default is 20Hz I believe).

hellfudge•3/21/24, 1:20 PM

Ok, thanks!

Boo Berry•3/21/24, 1:43 PM

Is there a setting to tighten up the center of the stick? When in top dead center it feels like ther is no resistance for the 1/8 inch all directions. There is just a little more play then I perfer and rather not have to set a big dead spot in game settings.

walmis•3/21/24, 1:49 PM

It's possible to tune the center using the spring mapping tool

walmis•3/21/24, 1:49 PM

🧰support

walmis•3/21/24, 1:50 PM

Also "adaptive recentering" will help keeping it centered

Boo Berry•3/21/24, 3:29 PM

Ok, thank you! I'll give it a try.

BAKE•3/21/24, 3:50 PM

I have ordered a replacement thermal Varistor,
But can someone tell me what this is?

Number481•3/21/24, 3:56 PM

looks like it used to be a fuse?

Number481•3/21/24, 3:57 PM

with the glass tube blown off? wild ass guess

Number481•3/21/24, 3:58 PM

looks like the guts of one of these... but I've never seen a fuse holder like the one in your picture so

BSpars•3/21/24, 8:20 PM

Does anyone know how to turn off the fourth hat option in the software? My Virpil Constellation does not have a fourth hat and the hat is being detected in some UI menus.

BSpars•3/21/24, 8:20 PM

BSpars•3/21/24, 8:27 PM

Wwalmis It's possible to tune the center using the spring mapping tool

Boo Berry•3/21/24, 8:53 PM

That worked!!! Thank you!!

scheppie_•3/21/24, 9:29 PM

hey, small question, for dcs ww2 planes, when i fly low speed or stand still, the stick is feeling nice, getting a good feel when you reach low speed with less wind, but from above 200 to max speed, i cant feel a different, i think with a steep dive on max speed the stick would feel verry heavy to turn, but i cant feel that.

WH grip is M36x2.0 Correct on the 5 pin to JST XH. My kit came with all the connectors other than

Similar Threads