TYou might be able to make it work by modifying since the nub in the middle is different between the two. I just got some off digikey, might be able to get those NS39 connectors there too.
BI ordered some 6 pin female panel connectors, I found a datasheet drawing of the 5s and 6s connectors. The difference is very minor.
Pretty sure I have the XH connectors in my RC stuff.
Xt30s to change out the motor power connectors. Since i have the 86 size motors. and a 300w PS.
Ordered 20amp resettable breaker,
What else....
Pretty sure I have the XH connectors in my RC stuff.
Xt30s to change out the motor power connectors. Since i have the 86 size motors. and a 300w PS.
Ordered 20amp resettable breaker,
What else....
B@walmis
i have a single motor connected on the bench, and It looks like VPForce doesnt recognize its connected.
i have a single motor connected on the bench, and It looks like VPForce doesnt recognize its connected.
BDo I have my connections right?
Ndisable the axis thats not connected
Biv tried disabling each axis one at a time. no luck.
it says in bottom right i have no motors connected
it says in bottom right i have no motors connected
Nyea, I see that now.... if you've verified the motor is getting power, I'm not sure what else to look at. The wiring isn't complex and looks right to me.
Bill dbl chk power
JI am not 100% sure but I think I saw someone with a similar problem some time ago and I believe it was that the motors are labeled X or Y and have to be plugged in as such into the M/B.
Blooks like power issue, though i dont know what could have happened between last night and today to make it not work anymore
NIIRC, there’s a green LED on the motor in the cavity where the connectors are. But I’m not sure if it’s just a power indicator or a board communication status indicator.
Nanyone had issues with the xplane 12 zibo 737 with control jitter while running telemffb?
BWould this explain my power supply not working?
Nyou are very likely the first person to try, to be honest. What you describe sounds like the axis position that TelemFFB is sending is fighting with what X-Plane is reading. The xplane plugin for TelemFFB sends the commands to override the axes, but there is a lot of unknown about how different 3rd party modules are implemented in xplane. Even the default R22 helicopter doesn't listen to the override command for the collective axis. It is entirely possible that many of the more advanced 3rd party aircraft won't work.
You can try disabling the axis control in TelemFFB and see if it clears up (this will also disable any trim/autopilot following). You can also try un-binding the axes in X-Plane.
You can try disabling the axis control in TelemFFB and see if it clears up (this will also disable any trim/autopilot following). You can also try un-binding the axes in X-Plane.
Naxis control was definatly the issue thankfully still useable without.\
HPlease help, I’m not getting any ffb on il2.
HThis is from rhino debug log
Nexplain more what you mean. There is nothing abnormal in that debug tab output
HWell I hoped it would work out of the box. I checked that ffb was enabled and everything else is default. In game I only have the rhino spring feeling, no ffb, rumble etc
Nthe native FFB in IL2 is limited to:
- Dynamic spring force based on airspeed
- ground bumps
- gunfire
- stall buffeting
FDid you use the TelemFFB?
Ntelemffb only adds supplemental and alternative (to the three I mentioned) effects. The actual 'FFB' (dynamic stick forces, trim following) are %100 handled by the game.
HNo telemffb, but it is not required right?
HDo I need to enable the effects in rhino to be overrided by the game?
Npost screenshots of your configurator effects and settings tab (win+shif+s for windows snip tool is your friend, vs pictures with your phone)
HYes I know I’m on a new setup and did not have Discord app installed yet
HOk there are ffb effects but they’re so weak it’s barely noticeable. 85% periodic effects and the stick barely vibrates when shooting. I guess I just need to crank everything to the max
Ncheck the "shake" slider in the IL2 FFB settings. It defaults to max, I believe, but just in case... Also your Periodic LPF value in the configurator expert settings will have an impact (default is 20Hz I believe).
HOk, thanks!
BIs there a setting to tighten up the center of the stick? When in top dead center it feels like ther is no resistance for the 1/8 inch all directions. There is just a little more play then I perfer and rather not have to set a big dead spot in game settings.
WIt's possible to tune the center using the spring mapping tool
WAlso "adaptive recentering" will help keeping it centered
BOk, thank you! I'll give it a try.
BI have ordered a replacement thermal Varistor,
But can someone tell me what this is?
But can someone tell me what this is?
Nlooks like it used to be a fuse?
Nwith the glass tube blown off? wild ass guess
Nlooks like the guts of one of these... but I've never seen a fuse holder like the one in your picture so 
BDoes anyone know how to turn off the fourth hat option in the software? My Virpil Constellation does not have a fourth hat and the hat is being detected in some UI menus.
B
B
BThat worked!!! Thank you!!
Shey, small question, for dcs ww2 planes, when i fly low speed or stand still, the stick is feeling nice, getting a good feel when you reach low speed with less wind, but from above 200 to max speed, i cant feel a different, i think with a steep dive on max speed the stick would feel verry heavy to turn, but i cant feel that.
Sis there a setting to change that?
VI really wish I had read this, you are not wrong it seems. Just got rhino and mcgu mkiv at the same time and the adapter will not work.
SI have the same dilemma but I still have a little way to go on getting my rhino. I have reached out to Walmis a couple of times to ask if there is any intention to release an updated Rev.C adapter but I haven't had a response yet. However there is a solution…
I have spoken to VKB and you can purchase the MCGU revB twist adaptor which is fully compatible.
My issue is I use extensions which is a little more problematic - VKB are offering to send me a cable to change the internals on the RevC extensions but I'm still not sure how that works.
I have spoken to VKB and you can purchase the MCGU revB twist adaptor which is fully compatible.
My issue is I use extensions which is a little more problematic - VKB are offering to send me a cable to change the internals on the RevC extensions but I'm still not sure how that works.
WThe 4th hat works like axis-to-button for the thumb stick, so if you calibrate the thumbstick the hat will work properly 
WI've finally received a revC extension today, and I'm pleased to say that I will be able to provide an adapter for the new revC mount
SAmazing news. Just after I spent all the money on adapters before I even get my rhino. 
patience was never my strong suit.
patience was never my strong suit.VI guess I’ll cancel my return then