And of course at the second attempt of attaching the extension i shred the 3d print
And of course at the second attempt of attaching the extension i shred the 3d print
B
F@walmis
Hhi, is it possible to use the rhino through vjoy and still have the force feedback in dcs? Or is it not recommended? Thanks
SDoes anyone have any good profiles preconfigured for the VPRhino with 57BLF03 motors? curious about the max amps collumn down the right hand side but would also love to know how other people configure the damper, spring, intertia etc
BAnd now I notice another feature of the z-extension and realise all my shenanigans from yesterday was all for nothing :facepalm:
It has locking screws for crying out loud..
In my defense there was no manual in the box.
It has locking screws for crying out loud..
In my defense there was no manual in the box.
MHa, I did the same thing. Same day too!
MHi guys, looking for a bit of guidance. If I mount the Thrustmaster grip, do I have to remove the silver screws before attaching or can I just screw the grip on like is?
WIt should just fit
MPerfect, thanks.
![[OR] SerGeant](https://cdn.discordapp.com/avatars/290181622832168961/338cff3e564800fa5a1068e9c25e28f5.webp?size=40)
[Hi guys, is there a way to turn on the fans permanently?
BThere is a "test fan" button or something in the debug section of the configurator.
BBut shouldn't really be any need to do it.
It will activate long before an actual issue.
It will activate long before an actual issue.
[I want to build a custom cooling solution to reduce the noise of the build in fans. So I am looking for a 12v permanent output on the PCB. An option to always on would be nice.
![[OR] SerGeant](https://cdn.discordapp.com/avatars/290181622832168961/338cff3e564800fa5a1068e9c25e28f5.webp?size=16)
TYou should put it in the wishlist 
SOn VKB adapter the locating screw diameter is too large to fit into the receiving chamber in the VKB MCG Pro grip for offset. I guess that isn't necessary since the grip can be oriented as desired then tightened down on the base with the adapter's cap. It's hard to believe that the adapter won't loosen under any unintended twisting of the grip though.
MSpeaking of VKB adaptors ... is there a way to connect that old KG12 grip to the Rhino (black box owned)?
VSure thing, VKB adaptor needs to be connected to a BlackBox, Rhino is not handling the grip. I’m using the same KG12, no issues.
SI was rotating the orientation of the base connector, something I see many have done. Any tips on reconnecting this cable again?
SI was convinced it would have more slack
SSolved! Never mind. Found the cable entering the stem on one of its sides.
Mgrateful for you taking the time to answer, but maybe I am stoopid or blind. But how do you fix the grip to the adaptor. I understand the need for the blackbox, but physically fixing the stick on top of the extension, how DO I Do that? Because just putting it on top does not hold ... ?
M
Syou need the locking nut + bolt from VKB
Sit goes in the round hole in the VKB connector
Syou can watch their YouTube video on how to connect a grip to Gunfighter for example
Mah ok, I guess I am missing that part then 
VThis little pin is what you need
Mah I see this clamps the two parts together with the gap towards the inside ... ?
Mthx , will see where I can get that.
THeyhey, i guess the 57blf03 motor wiring from the vpf kit is modified, right? The ones in the kit have 4 cables in total as far as i can see. Vendor Datasheets i found online and in old forum posts show motors with 7 cables.
TThe motors have a custom (as far as I know) pcb on the back.
AHi, how do you change the orientation of the stick? I don’t think it works either way unless you do something in the Rhino, right? I am using the TM stick
TThank you!:)
SYou swap around the connector, I just posted a pic from the process
AThanks, although I am not sure I understand. Do I have to unscrew the top part (2 little screws), then just rotate it and screw them again?
SYes. And in between fiddle with the cable length if you do not have enough slack to do that. You'll figure it out, a little fiddly but entirely user-doable.
SCareful not to pull much on the connector wires
SAlternatively, many extensions for TMs have just a plain cable in them, which allows you to rotate the grip freely.
SThat way there is no risk in changing out the orientation.
AThanks a lot
MAs an FYI Virpil sells extensions that use the same M36x2 mounting system as TM and Rhino. The 20cm “S” curve and Z-extension have the cable built in.
NHi! Just finished my Rhino build. I can't seem to be able to get the auto calibration to stick. I recalibrate but once that is done, it reverts to my previous calibration settings. Anyone got an idea on what I'm doing wrong?
MHey can someone take a look at this wiring for me? I’m well out of my depth
AJust to confirm, are you doing exactly as follows?
1. Click "Auto calibrate"
2. Click "Ok" on the pop-up screen
3. Move the stick to full deflection on both axes
4. Click "Auto calibrate" again
5. Click "Store settings"
1. Click "Auto calibrate"
2. Click "Ok" on the pop-up screen
3. Move the stick to full deflection on both axes
4. Click "Auto calibrate" again
5. Click "Store settings"
TLooks OK to me, PM Walmis and ask him to cast his eye over it. It's always tense hitting the power for the first time.
THow is this coming along @walmis ?
NYes, I did. It's reverting back to the full movement and not the restricted I have with the throw limiter.
W@Niklas [NiccoSWE] can you post a screenshot of the values after calibration?
MHallo, any idea when the aluminum grip adapter will be available (it is on back order at the moment).
WNext batch should arrive next week