ah ok, I guess I am missing that part then 😉
ah ok, I guess I am missing that part then 
VThis little pin is what you need
Mah I see this clamps the two parts together with the gap towards the inside ... ?
Mthx , will see where I can get that.
THeyhey, i guess the 57blf03 motor wiring from the vpf kit is modified, right? The ones in the kit have 4 cables in total as far as i can see. Vendor Datasheets i found online and in old forum posts show motors with 7 cables.
TThe motors have a custom (as far as I know) pcb on the back.
AHi, how do you change the orientation of the stick? I don’t think it works either way unless you do something in the Rhino, right? I am using the TM stick
TThank you!:)
SYou swap around the connector, I just posted a pic from the process
AThanks, although I am not sure I understand. Do I have to unscrew the top part (2 little screws), then just rotate it and screw them again?
SYes. And in between fiddle with the cable length if you do not have enough slack to do that. You'll figure it out, a little fiddly but entirely user-doable.
SCareful not to pull much on the connector wires
SAlternatively, many extensions for TMs have just a plain cable in them, which allows you to rotate the grip freely.
SThat way there is no risk in changing out the orientation.
AThanks a lot
MAs an FYI Virpil sells extensions that use the same M36x2 mounting system as TM and Rhino. The 20cm “S” curve and Z-extension have the cable built in.
NHi! Just finished my Rhino build. I can't seem to be able to get the auto calibration to stick. I recalibrate but once that is done, it reverts to my previous calibration settings. Anyone got an idea on what I'm doing wrong?
MHey can someone take a look at this wiring for me? I’m well out of my depth
AJust to confirm, are you doing exactly as follows?
1. Click "Auto calibrate"
2. Click "Ok" on the pop-up screen
3. Move the stick to full deflection on both axes
4. Click "Auto calibrate" again
5. Click "Store settings"
1. Click "Auto calibrate"
2. Click "Ok" on the pop-up screen
3. Move the stick to full deflection on both axes
4. Click "Auto calibrate" again
5. Click "Store settings"
TLooks OK to me, PM Walmis and ask him to cast his eye over it. It's always tense hitting the power for the first time.
THow is this coming along @walmis ?
NYes, I did. It's reverting back to the full movement and not the restricted I have with the throw limiter.
W@Niklas [NiccoSWE] can you post a screenshot of the values after calibration?
MHallo, any idea when the aluminum grip adapter will be available (it is on back order at the moment).
WNext batch should arrive next week
MI turned it on and didn’t die so that was nice
MIdk why but it didn’t come up with a raw value for the motor so I guess I have some reading to do tomorrow but it’s too late now
MAh don’t worry, I had to turn the y axis off
MNow I can go to sleep easy
DI have had my Rhino for a few weeks. It has always felt very weak , so today I have fiddled with every setting that I can tweak and still no joy.....I did open the debug page and there is all of these line items which state: FFB_RemoveEffect (9) and (15) and (16).....So I have probably screwed something up. Can anyone help get me on the right track again?
Cyou don't happen to have the potentiometer knob on the base turned way down do you?
TThere should be a default profile to load in the configs directory of the configurator. Also you can take a look at the profile sharing thread in the knowledge base to see how others have set theirs up.
WIf by weak you mean you want it more stiff at the center, you can tune the spring mapping:
🧰support
Also I recommend importing the default Rhino settings profile from
🧰support
Also I recommend importing the default Rhino settings profile from
configs/RHINO-defaults.vpconf@Chuff nope the knob is fully clockwise
D@walmis no, it feels no more stronger than my virpil at present. There is definitely something wrong or mis configured on my part
Cwhat module are you flying?
Cand are you running telemffb while in game?
DP51 and Huey mostly
DTelemffb is running
Cnot sure what the state of huey ffb support is, but the p51 has great ffb support and can get very heavy at times on the controls
DIf I could get a P51 profile to download, maybe it would fix what ever is out of whack.
Cdoes telemffb appear to working? in other words, when you load into the module in dcs you can see what module you're in in telemffb, and it's reporting what effects it's triggering?
DYes. Look at the pics I uploaded and see if you can spot something if you would,please
Cthose are from the configurator. I'm talking about telemffb. different application
DThe lower left pic is from the teleffb app
Cwhat does telem show if you open the settings tab?
DYou know, I just noticed something else, if you click on the upper right pic and look at the lower right hand corner, there seems to be motor errors….that can’t be good
CYeah, I'm out of ideas for you. sorry, man. Hopefully @walmis sees your last message about the motor errors.
DI am rebooting my computer now to see if that resets anything. Do you have a P51 profile that you would share?
CI pretty much run it at default. just tweaked the settings to my liking in telemffb. So I turn things like runway rumble way down. Other than that I didn't do a lot of tweaking. found it to be pretty good for me out of the box