MPerfect, thanks.
![[OR] SerGeant](https://cdn.discordapp.com/avatars/290181622832168961/338cff3e564800fa5a1068e9c25e28f5.webp?size=40)
[Hi guys, is there a way to turn on the fans permanently?
BThere is a "test fan" button or something in the debug section of the configurator.
BBut shouldn't really be any need to do it.
It will activate long before an actual issue.
It will activate long before an actual issue.
[I want to build a custom cooling solution to reduce the noise of the build in fans. So I am looking for a 12v permanent output on the PCB. An option to always on would be nice.
![[OR] SerGeant](https://cdn.discordapp.com/avatars/290181622832168961/338cff3e564800fa5a1068e9c25e28f5.webp?size=16)
TYou should put it in the wishlist 
SOn VKB adapter the locating screw diameter is too large to fit into the receiving chamber in the VKB MCG Pro grip for offset. I guess that isn't necessary since the grip can be oriented as desired then tightened down on the base with the adapter's cap. It's hard to believe that the adapter won't loosen under any unintended twisting of the grip though.
MSpeaking of VKB adaptors ... is there a way to connect that old KG12 grip to the Rhino (black box owned)?
VSure thing, VKB adaptor needs to be connected to a BlackBox, Rhino is not handling the grip. I’m using the same KG12, no issues.
SI was rotating the orientation of the base connector, something I see many have done. Any tips on reconnecting this cable again?
SI was convinced it would have more slack
SSolved! Never mind. Found the cable entering the stem on one of its sides.
Mgrateful for you taking the time to answer, but maybe I am stoopid or blind. But how do you fix the grip to the adaptor. I understand the need for the blackbox, but physically fixing the stick on top of the extension, how DO I Do that? Because just putting it on top does not hold ... ?
M
Syou need the locking nut + bolt from VKB
Sit goes in the round hole in the VKB connector
Syou can watch their YouTube video on how to connect a grip to Gunfighter for example
Mah ok, I guess I am missing that part then 
VThis little pin is what you need
Mah I see this clamps the two parts together with the gap towards the inside ... ?
Mthx , will see where I can get that.
THeyhey, i guess the 57blf03 motor wiring from the vpf kit is modified, right? The ones in the kit have 4 cables in total as far as i can see. Vendor Datasheets i found online and in old forum posts show motors with 7 cables.
TThe motors have a custom (as far as I know) pcb on the back.
AHi, how do you change the orientation of the stick? I don’t think it works either way unless you do something in the Rhino, right? I am using the TM stick
TThank you!:)
SYou swap around the connector, I just posted a pic from the process
AThanks, although I am not sure I understand. Do I have to unscrew the top part (2 little screws), then just rotate it and screw them again?
SYes. And in between fiddle with the cable length if you do not have enough slack to do that. You'll figure it out, a little fiddly but entirely user-doable.
SCareful not to pull much on the connector wires
SAlternatively, many extensions for TMs have just a plain cable in them, which allows you to rotate the grip freely.
SThat way there is no risk in changing out the orientation.
AThanks a lot
MAs an FYI Virpil sells extensions that use the same M36x2 mounting system as TM and Rhino. The 20cm “S” curve and Z-extension have the cable built in.
NHi! Just finished my Rhino build. I can't seem to be able to get the auto calibration to stick. I recalibrate but once that is done, it reverts to my previous calibration settings. Anyone got an idea on what I'm doing wrong?
MHey can someone take a look at this wiring for me? I’m well out of my depth
AJust to confirm, are you doing exactly as follows?
1. Click "Auto calibrate"
2. Click "Ok" on the pop-up screen
3. Move the stick to full deflection on both axes
4. Click "Auto calibrate" again
5. Click "Store settings"
1. Click "Auto calibrate"
2. Click "Ok" on the pop-up screen
3. Move the stick to full deflection on both axes
4. Click "Auto calibrate" again
5. Click "Store settings"
TLooks OK to me, PM Walmis and ask him to cast his eye over it. It's always tense hitting the power for the first time.
THow is this coming along @walmis ?
NYes, I did. It's reverting back to the full movement and not the restricted I have with the throw limiter.
W@Niklas [NiccoSWE] can you post a screenshot of the values after calibration?
MHallo, any idea when the aluminum grip adapter will be available (it is on back order at the moment).
WNext batch should arrive next week
MI turned it on and didn’t die so that was nice
MIdk why but it didn’t come up with a raw value for the motor so I guess I have some reading to do tomorrow but it’s too late now
MAh don’t worry, I had to turn the y axis off
MNow I can go to sleep easy
DI have had my Rhino for a few weeks. It has always felt very weak , so today I have fiddled with every setting that I can tweak and still no joy.....I did open the debug page and there is all of these line items which state: FFB_RemoveEffect (9) and (15) and (16).....So I have probably screwed something up. Can anyone help get me on the right track again?
Cyou don't happen to have the potentiometer knob on the base turned way down do you?
TThere should be a default profile to load in the configs directory of the configurator. Also you can take a look at the profile sharing thread in the knowledge base to see how others have set theirs up.