There is a default Rhino config in the `configs/RHINO-defaults.vpconf`, click import then store con

There is a default Rhino config in the

configs/RHINO-defaults.vpconf

configs/RHINO-defaults.vpconf

,
click import then store config. Also make sure to to run auto calibration after, since your calibration was reset too probably.

Wwalmis There is a default Rhino config in the `configs/RHINO-defaults.vpconf`, click i...

Dentedend10•5/24/24, 2:21 PM

Thank you!!

Dentedend10•5/24/24, 2:22 PM

And do you have any solution for the F14 stick problem? If not then I’ll need to get another adapter. In the end I was able to hammer it down but there is no way it will come off now

DDentedend10 And do you have any solution for the F14 stick problem? If not then I’ll need to...

walmisOP•5/24/24, 2:47 PM

Hmm, is it the shaft itself or the small pin that's the issue?

Littlesack•5/24/24, 4:10 PM

How can I fix this behavior? This is in dcs with the apache. I hold trim release and move the stick, but the center does not remain where the stick is physically and when I release the trim button the stick moves back to a different "center" than where it should be

LLittlesack How can I fix this behavior? This is in dcs with the apache. I hold trim release...

Number481•5/24/24, 4:12 PM

get rid of your axis curves in DCS

Littlesack•5/24/24, 4:13 PM

Thanks, forgot I had put any in

Number481•5/24/24, 4:22 PM

everyone does

Wwalmis Hmm, is it the shaft itself or the small pin that's the issue?

Dentedend10•5/24/24, 6:26 PM

The shaft itself. Even on the vkb extension there is a little bit of resistance compared to the gunfighter, but it feels like rubbery resistance and goes down fairly easy. But on the VPFORCE extension grip it takes more force than I can put on it. Only way was with a hammer

Fresh_Mint•5/25/24, 3:02 PM

Is it normal? I use spring gain 20% with Max current 30A. So when full draw, axis current should show ~6A. But full aft shows 6.6~6.7A whereas full fwd, left and right shows ~6A

FFresh_Mint Is it normal? I use spring gain 20% with Max current 30A. So when full draw, axi...

walmisOP•5/25/24, 3:28 PM

Yeah, that's normal. Anticogging takes some current

Fresh_Mint•5/25/24, 3:37 PM

Oh I see thanks!

A. Palmetto•5/25/24, 6:23 PM

trying to open telemffb

AA. Palmetto trying to open telemffb

Number481•5/25/24, 6:48 PM

Generally caused by one of two things.

1: Windows Defender or other AV ate some files due to false positive malware detection
2: You accidentally copied the exe out of the folder rather than creating a shortcut

Wwalmis Yeah, that's normal. Anticogging takes some current

Hiob•5/25/24, 7:18 PM

Speaking of currents, I have a question about the motors: If I noticed correctly the fan activates when either motor (usually the pitch) reaches 50 C and turns of when under 45 C give or take, but I wonder what would be the critical temperature for the motors before they take damage? I can’t find any specs about it. 60, 70, 80 C…. when will they take damage?
I’m asking, 1. out of curiosity and 2. because I will use the same motor and pcb in my pedals-mod, but without a cooler. I assume it will work out, but who knows….. (btw. when will the current limiter set in?)

walmisOP•5/25/24, 7:20 PM

I guess the limiting factor would be the motor's magnet curie temperature, at which they start to demagnetize, which is unknown. But anyhow the motors are thermally limited, similarly how GPUs self limit to maintain a stable max temp.

NNumber481 Generally caused by one of two things. - 1: Windows Defender or other AV at...

A. Palmetto•5/25/24, 7:38 PM

I redownloaded via the link in telem ffb rather than GitHub then updated and it worked.

lol I was trying to run inside the folder but it works now

sabreman•5/25/24, 11:48 PM

hey so my red power interrupt button came loose and now spins freely

sabreman•5/25/24, 11:48 PM

how can i tighten it down? do i need to rip the wheels off to pull the top cover?

sabreman•5/26/24, 12:41 AM

I ended up doing just that. Is there a way to pull the red part off the button? I tignened it down, but idk if it'll hold long term

Ssabreman I ended up doing just that. Is there a way to pull the red part off the button? ...

Number481•5/26/24, 12:48 AM

For future ,you should be able to get to the nut with a pair of needle nose pliers just by removing the front panel.

Vassilli•5/26/24, 1:42 AM

So, soon to get my order thingy. Im in the processing stage, has anyone used the base with a thrustmaster warthog OG grip? I'm worried about the metal thing breaking. What sticks are you guys using? Sorry if its the wrong channel

NNumber481 For future ,you should be able to get to the nut with a pair of needle nose plie...

sabreman•5/26/24, 2:31 AM

God that would have been way smarter. i had to pull both big wheels off and everything going throgh the top lol

sabreman•5/26/24, 2:31 AM

ill keep that in mind next time it gets loose

Fresh_Mint•5/26/24, 4:09 AM

I think anticogging for y axis is not working perfectly. I could feel minute bump at a center of y axis movement(x axis is perfectly smooth). Can it be caused by a belt is too tight?

Fresh_Mint•5/26/24, 4:11 AM

Or just defect of motor?

Fresh_Mint•5/26/24, 4:20 AM

When the power turned off, I can feel much stronger cogging than x axis's

FFresh_Mint I think anticogging for y axis is not working perfectly. I could feel minute bum...

LeLv30_Superbus•5/26/24, 6:17 AM

FWIW I had a similar situation which was solved by removing 20 cm extension + VKB adapter and installing a 10 cm extension. Never found out which one caused it. The bump/noise was also only in Y axis like in your case. Could be something completely different though and idk whether you are even using an extension or adapter.

FFresh_Mint When the power turned off, I can feel much stronger cogging than x axis's

walmisOP•5/26/24, 6:28 AM

Yeah, when the belt is too tight it will introduce some cogging-like feel. You can verify however how the small pulley spins with the belt removed.

Fresh_Mint•5/26/24, 7:17 AM

@Fourgrinder Oh I don't use any extension and adapter

anyway thank you for your case

Fresh_Mint•5/26/24, 7:19 AM

@walmis Ok I'll try, thank you!

Ssabreman God that would have been way smarter. i had to pull both big wheels off and ever...

Touch_Of_Legend•5/26/24, 9:37 AM

Keep in mind if you wanted to mount the Rhino the other way you can also rotate the stop button this way so it’s still facing you and saying “stop” or whatever.

All you do after that is Invert the Axis in the Vpconfig software (NOT in games!)

VVassilli So, soon to get my order thingy. Im in the processing stage, has anyone used the...

Fr4Ged•5/26/24, 10:42 AM

I used the Rhino with the TM F-16/Warthog grip for a while but changed to a Virpil Constellation rather quick.
It works but the Warthog isn't just my cup of tea. Way to heavy and stiff feeling. That is just personal preference though.
It works well and keeps its balance with decent spring settings.

WhereNoLarkFlew•5/26/24, 12:29 PM

Anyone know if you can use Virpil Alpha thumb stick as buttons in each direction? There was a way to do that in Virpil Software - any ideas on how to mimic that in the VPForce config?

WWhereNoLarkFlew Anyone know if you can use Virpil Alpha thumb stick as buttons in each direction...

Fr4Ged•5/26/24, 12:43 PM

identify the HAT number in the Vpforce tool and then click it in "Hats as buttons"

FFr4Ged identify the HAT number in the Vpforce tool and then click it in "Hats as button...

WhereNoLarkFlew•5/26/24, 12:53 PM

Awesome, thanks boss - must have missed that.

dogdayz•5/26/24, 1:04 PM

Hey, i'm having trouble sending the '!info emailadress' message to the bot, am i missing something?

Fr4Ged•5/26/24, 1:09 PM

what is the bot responding if you have trouble then?

FlatSpin•5/26/24, 1:13 PM

working for me

LAUZBOT•5/26/24, 2:11 PM

@walmis, I had a billing issue (fraud screening). I've cleared the issue, can you DM to figure out next steps?

LLAUZBOT @walmis, I had a billing issue (fraud screening). I've cleared the issue, can yo...

walmisOP•5/26/24, 2:38 PM

Hi, looks like payment went through fine. So all looks good!

FFresh_Mint I think anticogging for y axis is not working perfectly. I could feel minute bum...

Hiob•5/26/24, 2:39 PM

Check if the motor pulley is firmly tightened on the axis. I forgot to loctide it properly and it came loose. It didn’t slip completely, but it had play which lead to a „cogging“ feel around the middle position.

VVassilli So, soon to get my order thingy. Im in the processing stage, has anyone used the...

Hiob•5/26/24, 2:40 PM

I‘m using a TM metal grip. So far, all is fine. I‘m planning to switch to a Virpil just for length reasons though.

Wwalmis Hi, looks like payment went through fine. So all looks good!

LAUZBOT•5/26/24, 2:52 PM

Okay thank you! If anything comes up, let me know. Happy to assist however I can, thx you for making these sticks! I've been on the list for almost a year lol

LLAUZBOT Okay thank you! If anything comes up, let me know. Happy to assist however I can...

WhereNoLarkFlew•5/27/24, 1:27 AM

You’re in for a great experience. I can’t imagine going back to a spring based stick

Fresh_Mint•5/27/24, 2:39 AM

@Hiob oh I'll look at that also thank you

slowmover•5/27/24, 5:59 AM

Hello mates. With what filament you print the gimbal? and how much infill usually use ?

mark turner•5/27/24, 7:31 AM

Hi, in relation to the Heatblur Phantom.....I am interested in introducing a bit less sensitivity , to help out in refueling....with a "normal" stick, this is easily done by introducing some curve to teh axis, however, obviously, this is not good practice with an FFB stick. Is there a way within the config file options to emulate this effect at all? Thank you.

Sslowmover Hello mates. With what filament you print the gimbal? and how much infill usuall...

Hiob•5/27/24, 8:46 AM

I got my parts pre-printed from Winger. He used CF-PETG iirc. However out of curiosity and for DIY test purposes I printed a gimbal half from regular PETG myself and it seems plenty strong enough.

Hiob•5/27/24, 8:47 AM

However. The week link isn’t the gimbal (I think). but the central hub/gimbal-stick-connector.

Hiob•5/27/24, 8:48 AM

I still think it can be printed from PETG, but you need to think about layer orientation.

There is a default Rhino config in the `configs/RHINO-defaults.vpconf`, click import then store con

Similar Threads

Similar Threads

Similar Threads