I put in an order on May 20th, but have never received confirmation. Can you help?
I put in an order on May 20th, but have never received confirmation. Can you help?
FThanks for your help. It says that I don't have permission to send messages on this channel....
Fyou can just directly message the bot
MHi, just found that "Breakout Force" at 5% makes forward trim unusable in the A-10Cii
FI've tried, but all it says is that it does not understand me. FRUSTATING.
Fjust type:
"!info your.email@emailhost.com"
"!info your.email@emailhost.com"
Fwith your personal e-mail obviously
VHi everyone. Sometimes it happens that when I fly my roll trim get stuck, so my stick push to one of the sides. If I trim back the trim in the sim get back to full left (or right). I have more than one grip (virpil alpha and virpil vfx) and it happens with both. So I don't think it is the grips.
Did it happen to someone else?
Did it happen to someone else?
FThanks! That worked. I really appreciate the help.
KIt happened to me 3 times but with nose down trim on pitch. I've switch off rhino, reloaded vpcvonfig and switched it back again, that cleared it. Unusual and very random
VOk so there must be some bug in the firmware
VIt happened to me 3 times in the same flight
WWhich aircraft? Could be DCS is sending wrong trim data
VThe F-14
VIt is not the first time it happened to me, but now it happened 3 times in a row
VIn the DCS controls indicator the trim indicator moves (when it does happen) like If I was pressing the trim left (or right)
WThere's something bugged in the F-14 trim implementation. Last time I tested, sometimes trim runs away when switching pilot/rio seats.
VTo "reset" this behavior I just press the offending input (trim left in my above example) and then of course retrim back to center
VYeah that's I know, and also ACLS is not working
WRhino only gets commands like - set this new center at (x,y)
VBut I was in MP with an human rio
VWhat I can try is to unbind trim left/right and see if that happens again
KI had that in F-4E
WI doubt it's the buttons...
VYeah me too...but to rule out stuff
Vso HB modules (for now)
BJust had it happen in the Av8b and I've had it happen in the F5 about 6 months ago
NCan anyone confirm if this happens without TelemFFB running? Just want to confirm the trim workaround feature isn't bugged or something. Though it is only enabled by default on the AV8B and Mig-19
BI'll try to replicate it without the Telem and let you know
VI had TelemFFB running, but the F14 has its own trim implementation, and I am sure trim workaround is not enabled on my end
KI don't use trim workaround and had it again 1h ago, short bump of trim button in the same direction as runaway, fixed the problem. It occurred when pressed and hold so I suspect ghosting issue on reading phase by DCS
Vexactly...short bump of tim button in the same direction fixes the issue (temporarly)
II have a 9.5A power brick that came with my Rhino, it's set to 7.0A in the software, shoud I change this to 9.5A?
IElectricity is NOT my area of expertise, so I'm asking first lol.
IOr is the "PSU Current" in the configurator unrelated to your power brick?
DMaybe a stupid question but is it okay if the blue marked grid is blocked?
The cooler below has unrestricted airflow but the blue marked area is directly in front of my seat cushion, so the question is how close can i put it near the cushion?
The cooler below has unrestricted airflow but the blue marked area is directly in front of my seat cushion, so the question is how close can i put it near the cushion?
MJust noticed last night that the red stop button isn't disconnecting the motors when it's pressed so the only way stop the joystick moving is to physically unplug it.
Is this a known issue and if is there any way to resolve it ?
Is this a known issue and if is there any way to resolve it ?
AHey @walmis - any reason why my new toy would only recognise a TM Warthog grip and not a Realsimulator or Vipril Warbird?
WIf it recognizes the TM and not Virpil/RS is very odd. Since both use the same signalling. The only thing comes to mind is it's not making a proper electrical connection at the 5 pin mini din socket.
AOk, any suggestions to rectify that?
AThanks for such a speedy reply.
WMake sure it's inserted fully. Try pressing a button on the grip and push/wiggle the connector in the base and see if the button indicator in the VP configurator shows any action.
BI have the winwing adapter but need the stick to be just a bit longer. I made my own adapter and extention to go from vp rhino to winwing grip but now I have to make/buy a plug for the wiring. I see that the rhino base uses a 5pin female and the winwing uses a 6pin male plug. What does 6th pin do, do i need it. I have a short 6pin to 6pin, can I pull the 6th pin out and use that cable?
TCan you not put the WW adapter on top of your new adapter and go 5 pin to 5 pin?
Rhino (5) to new adapter (5 to 5) to WW adapter (5 to 6).
Rhino (5) to new adapter (5 to 5) to WW adapter (5 to 6).
BUnfortunately it would be too long at that point. Plus the adapter doesn't really tighten very well. Always has this loose feel where you can't tighten it enough and twists.
TI’ve seen a few people use a rubber oring to help snug it up. But have you tried removing the screws and seeing what’s inside the WW adapter? I don’t think it’s just a straight pass through cable with one pin removed. I think there is more to it. But if you can get it apart you may be able to transfer the guts over to your adapter.
BI did take the screws out but that's as far as I went. I was afraid to try and take the wires out in case I broke anything, still have to use it for now. I'm hoping there is a wire diagram showing which pins are being used and where they go.
TI want to say there is a PCB in there from what I have seen others discuss on the topic but I am not sure, you may have to ping Walmis.
AWhen I start VPforce Configurator any idea why the "green circle" is on the upper right corner?
