Hi, were you able to stop the X motor from shutting down? If not, have you tried disabling the axis

Hi, were you able to stop the X motor from shutting down? If not, have you tried disabling the axis scaling due to the unbalance between left X axis and right X axis, just for testing?

GGarrafaBr Hi, were you able to stop the X motor from shutting down? If not, have you tried...

PiNKSH!T•6/12/24, 2:19 AM

I use a physical limiter & those axis scaling settings keep everything calibrated/centered

GGarrafaBr Hi, were you able to stop the X motor from shutting down? If not, have you tried...

PiNKSH!T•6/12/24, 6:46 AM

So atm with these settings things are stable

PPiNKSH!T So atm with these settings things are stable 🤷‍♂️

GarrafaBrOP•6/12/24, 8:14 AM

I see, with Inertia and friction disabled, the shutdown is gone.

GGarrafaBr I see, with Inertia and friction disabled, the shutdown is gone.

PiNKSH!T•6/12/24, 8:18 AM

No, in fact I tested that last night & it persisted. It may have helped a small amount but I couldn't say so. I think the main thing was turning the LPF for damper down 1hz to 3.0hz & 7% seems to be stable for the ETL effect.

Boo Berry•6/12/24, 12:36 PM

@BAKE Hello, I'm trying to make my own extension cable from the rhino base to a winwing stick, did this pin out work for you?

BBoo Berry @BAKE Hello, I'm trying to make my own extension cable from the rhino base to a ...

TheAmazinGreat•6/12/24, 1:17 PM

That pinout is only for TM stick on Winwing base. It won’t work the other way around without the WW adapter internals.

Boo Berry•6/12/24, 1:48 PM

Ok, so you need to have a special parts besides just the connectors to go from the rhino to winwing. So what do I need?

I have the adapter but I can't get it tight enough even with o-rings installed to stop from twisting. I was trying to come up with my own adapter machined from aluminum but need a wire harness now.

BBoo Berry Ok, so you need to have a special parts besides just the connectors to go from t...

TheAmazinGreat•6/12/24, 2:16 PM

Have you seen this post, may be worth a try. 📃general

Boo Berry•6/12/24, 2:18 PM

I have not, but now I have and will give it a try!!! Thank you!!

BBoo Berry @BAKE Hello, I'm trying to make my own extension cable from the rhino base to a ...

BAKE•6/12/24, 3:05 PM

Sorry, I havent actually worked on it.
i basically gathered all the parts I need, but have gotten busy with work and life.

Skood•6/13/24, 12:13 PM

In the process of turning my base around and reversing the grip connector the yellow wire had come out of the white connector. I have managed to push it back in and it appears to be working ok at the moment but wondered if this is readily available cable I could purchase either locally, or via VPForce, and easily replace if my temporary fix doesn’t hold up?

SSkood In the process of turning my base around and reversing the grip connector the ye...

walmis•6/13/24, 12:14 PM

Yeah, you can definitely use the order form to order spare parts

Wwalmis Yeah, you can definitely use the order form to order spare parts

PiNKSH!T•6/13/24, 1:43 PM

hey m8 any idea what would be causing the center to jump to the side like this? So far I've only noticed this only happens when I load the Kiowa?

PiNKSH!T•6/13/24, 1:43 PM

just loaded a training mission & it jumped to the side from centre

PiNKSH!T•6/13/24, 1:44 PM

https://discord.com/channels/965234441511383080/968208779084701716/1250340358663966863see there it's center

Discord

Discord - Group Chat That’s All Fun & Games

Discord is great for playing games and chilling with friends, or even building a worldwide community. Customize your own space to talk, play, and hang out.

PPiNKSH!T just loaded a training mission & it jumped to the side from centre

Bob Bushman•6/13/24, 1:44 PM

Maybe it starts off with a trimmed position?

BBob Bushman Maybe it starts off with a trimmed position?

PiNKSH!T•6/13/24, 1:45 PM

oh this has started in the air

PiNKSH!T•6/13/24, 1:45 PM

thank you

Bob Bushman•6/13/24, 1:46 PM

Don't know for sure, but that's my first guess.

BBob Bushman Don't know for sure, but that's my first guess.

PiNKSH!T•6/13/24, 1:46 PM

it likely is. I'll confirm in a min

walmis•6/13/24, 1:54 PM

Yes, the Sim/application drives the center position

omohat•6/13/24, 2:43 PM

Has anyone managed to replace the fan with a quieter one (like a Noctua). Or if not can you share any details of what spec fan (size and plug) I should be looking for?

walmis•6/13/24, 2:49 PM

I'll add provisions to the new firmware to adjust the fan settings to make them more quieter

Number481•6/13/24, 2:59 PM

so... who's going to be first to seal all the joints on their rhino and then fill her up with actively cooled mineral oil?

Wwalmis I'll add provisions to the new firmware to adjust the fan settings to make them ...

omohat•6/13/24, 3:27 PM

Would it have any implications for heat/life?

omohat•6/13/24, 3:31 PM

Thats why I was leaning towards upgrading the fan - to ensure airflow would stay the same but noise should come down

omohat•6/13/24, 3:31 PM

I wouldn't want to just turn the fan speed down to make it quieter and then find its causing problems with component heat and life

walmis•6/13/24, 3:35 PM

nah, it won't cause any issues since motors have thermal management built in. But anyway the fan specs are: 60x60x10, 12V

omohat•6/13/24, 4:51 PM

https://www.amazon.com/WINSINN-Bearings-Brushless-Cooling-60mm10mm/dp/B08R9JNB2Y

Like this? And would 2 pin be ok?

WINSINN DC 60mm Fan 12V 6010 Dual Ball Bearing Brushless Cooling 60...

WINSINN DC 60mm Fan 12V 6010 Dual Ball Bearing Brushless Cooling 60mmx10mm 2PIN (Pack of 2Pcs)

omohat•6/13/24, 4:51 PM

In any case I'll probably wait for your firmware update first and see how that goes but doesn't hurt to do a bit of research in the meantime

walmis•6/13/24, 4:52 PM

Those won't be any quieter I reckon

omohat•6/13/24, 4:53 PM

Hmmm ok

omohat•6/13/24, 4:55 PM

It looks like the "good" quiet options are 60x60x25 (noctua and coolermaster)

omohat•6/13/24, 4:55 PM

that definately wont fit right?

walmis•6/13/24, 4:56 PM

It would fit in the front, but in the rear it would need to stick outside the case.

omohat•6/13/24, 4:57 PM

I'll wait for your firmware update then and see how things are after that

FarFutureFox•6/13/24, 8:19 PM

I have some issues:
(1) the stick vibrates when neither the Config or TelemFFB apps are running
(2) the gain pot on the base isn't working
(3) the force is odd and not responding to adjustments in the config app.
I've restarted Windows, checked for firmware updates, I'm applying the changes. It's my first day with the Rhino, so I may be doing something wrong, but it all looks strange. Any ideas?

FFarFutureFox I have some issues: (1) the stick vibrates when neither the Config or TelemFFB ...

Number481•6/13/24, 9:37 PM

1.) Vibrating? Or oscillating? If its oscillating, thats likely caused by too high gain on friction/damper or having the spring mapping pulled in too tight. If its actually vibrating (like an engine rumble), it could be a stuck effect. Look in the debug tab of the configurator software to see what effects are active ("Loaded Effects" pane on the right side of the page). Square/Sine/Triangle/Sawtooth are periodic (vibration) type effects.
2.) How is the pot configured in the configurator software? You can connect the pot to any of the sliders, but its probably set to "none" by default
3.) not sure I understand. Can you elaborate?

Boo Berry•6/13/24, 11:52 PM

Is there a way to set a button on my winwing Orion throttle to control the hardware force trim for the rhino joystick. Another words, turn a knob on my throttle to pitch nose up or down instead of a button on my joystick?

BBoo Berry Is there a way to set a button on my winwing Orion throttle to control the hardw...

PiNKSH!T•6/14/24, 2:45 AM

Check out the VPforce Loopback app, it may be able to do this, you would probably need hid hide too??

bert•6/14/24, 9:27 AM

Recently i'm noticing my X-Axis being offset a few percent, using Protomakers DIY base, Virpil 20cm extension + Constellation Alpha grip. I guess it's caused by the rather long extension + heavy grip? Whatever i set in the balance spring, i can't get it to properly center without using adaptive recentering.
Even if i rotate the grip bringing the brake handle over to the right side, it still feels like there is a bias pulling the stick to the left, away from center. Any idea whats wrong?

Kowalsky•6/14/24, 9:32 AM

New calibration?

Bbert Recently i'm noticing my X-Axis being offset a few percent, using Protomakers DI...

walmis•6/14/24, 9:37 AM

Try adding some static force to the Right

walmis•6/14/24, 9:38 AM

maybe there's some misalignment in the gimbal causing some force to the left

KKowalsky New calibration?

bert•6/14/24, 9:38 AM

Autocalibrate didn't solve it

Wwalmis maybe there's some misalignment in the gimbal causing some force to the left

bert•6/14/24, 9:40 AM

Completely forgot about the static force effect.. thanks

Could be the gimbal, i did notice odd sounds from time to time, guess i'll have to take it all apart again at some point.

I/JG7_Moto•6/14/24, 12:14 PM

@walmis @Number481 There is an issue in IL2 where we cannot get full elevator with the Rhino, this picture is with the stick pulled all the way back, VPforce default configuration. How can I full elevator deflection with the Rhino? which settings do I need to change?

I/JG7_Moto•6/14/24, 12:15 PM

I/JG7_Moto•6/14/24, 12:16 PM

Same problem with aileron

I/JG7_Moto•6/14/24, 12:16 PM

Hi, were you able to stop the X motor from shutting down? If not, have you tried disabling the axis

Similar Threads