Oh, that screenshot was before I loaded the default config. I missed that. Still, after loading the

Oh, that screenshot was before I loaded the default config. I missed that. Still, after loading the default Rhino config and spring effect strength at 100 the issue persist.

Ffrumpy Oh, that screenshot was before I loaded the default config. I missed that. Still...

Hiob•7/24/24, 7:01 PM

What happens when you reset the motors in the debug tab?

amadeus•7/24/24, 7:01 PM

what does your debug tab show?

frumpyOP•7/24/24, 7:02 PM

the two resets were made by me.

walmis•7/24/24, 7:08 PM

Looks like some application created an inactive spring force or maybe the effect left dangling.
If you run DCS you need to start the actual flight, otherwise the stick will be limp in the menu.

Ffrumpy the two resets were made by me.

amadeus•7/24/24, 7:30 PM

so according to your debug tab -- there are no springs applied, you said you applied a spring in your previous screenshot -- but it's not showing there, did you press apply affter setting the spring values to 100%?

amadeus•7/24/24, 7:31 PM

(also yeah -- if you're running a game at the moment, it may override what you're doing)

frumpyOP•7/24/24, 7:36 PM

I started DCS and the A-10, worked fine and when quitting, the spring came back. Thank you guys!

amadeus•7/24/24, 7:48 PM

as a general thing for me -- i like to have no forces applied by default, so it's obvious when the game takes over

RoboGeoff•7/24/24, 9:10 PM

@walmis Is there any ETA on the updates for RealSimulator grips? I'm using a RS F-18 grip and there are three major buttons that are not detected using the RealSimulator grip profile. They are Recce depress, Sensor Control depress and Trim hat depress. I screen shoted the debug info for these three buttons, and I was wondering if this information would help updating the RS F-18 grip. Thanks

RoboGeoff•7/24/24, 9:17 PM

CCheck6 I'm ready to give up , my winwing adapter doesn't work. Can someone please tell ...

TrigaNZ•7/24/24, 10:16 PM

I had mine apart yesterday for other reasons and I discovered that the plug in the Rhino had slipped down and was not making correct contact with the adaptor. You can take off the two screws and lift it up a but, push the cable up from the bottom to help. (remove the dust cover.)

RRhino @walmis I'm getting the 32 button error with my winwing adapter, I've tested the...

Rhino•7/25/24, 1:22 PM

@walmis sorry to ping again but the winwing adapter doesnt work for me either

142nd_Bama•7/25/24, 2:26 PM

Finally got my rhino base built late last night, plan on plugging it in this afternoon. I’ve yet to have time to comb thru the manual… if a few short words can someone explain the purpose of the setting vs effect vs teleffb or whatever it is. Keep in mind I only fly dcs and mainly helos! Thanks in advance!

RRhino @walmis sorry to ping again but the winwing adapter doesnt work for me either

TheAmazinGreat•7/25/24, 2:57 PM

Have you tried pushing down the connector hard to make sure it’s seated? A lot of times it seems the pins just need a little extra to make contact.

VRS-410 Sakkay•7/25/24, 3:00 PM

Hi. What does it: new privat slash command -mean?

Spitfire ZX•7/25/24, 3:06 PM

pretty sure it's these

VVRS-410 Sakkay Hi. What does it: new privat slash command -mean?

Bob Bushman•7/25/24, 3:06 PM

Just another way to talk to the bot.

Bob Bushman•7/25/24, 3:08 PM

With the info command followed by your email you get a bit response with how it's going, only you will actually see those messages so don't worry.

AdiSz•7/25/24, 3:49 PM

Hi, couldn´t use my rhino for a long time. Now there is a new firmware.(I´m still on 1.0.15) but I cannot download it. (not in chrome nor in MS edge).

1142nd_Bama Finally got my rhino base built late last night, plan on plugging it in this aft...

Dracks•7/25/24, 7:48 PM

In a nutshell:

- You have the configuration software
- you have the effects software (telemffb)
- you've got DCS

Read the manual carefully, because you'll have all the answers and more in just a few minutes!

You need to configure your Rhino (1st software) then DCS (important because it natively manages ffb). Then run telemffb, which gives you the effects for each plane/helicopter. Most of them are directly recognized.

After that, you're left with the little details (which will take some time).

Dracks•7/25/24, 7:51 PM

And after you go to the canal telemffb_user and learn a lot !

Dracks•7/25/24, 7:51 PM

Some users had posted chopper profile

142nd_Bama•7/26/24, 2:56 AM

so i somewhat had it working, downloaded telemffb, downloaded a file from the #

knowledge-base and my stuff went crazy, tried to start all over agin with the first "center" calibration and now my figures arent near 2000, any ideas?

142nd_Bama•7/26/24, 2:56 AM

AAdiSz Hi, couldn´t use my rhino for a long time. Now there is a new firmware.(I´m stil...

walmis•7/26/24, 6:59 AM

Try this fix:
🧰support

142nd_Bama•7/26/24, 2:12 PM

Is there a setting to give more holding power at the central trimmed position? Looking for a more constant spring load as opposed to progressive.

1142nd_Bama Is there a setting to give more holding power at the central trimmed position? L...

[

[OR] SerGeant•7/26/24, 3:18 PM

Adaptive Recentering is your friend.

[[OR] SerGeant Adaptive Recentering is your friend.

142nd_Bama•7/26/24, 3:26 PM

Ummmm. It does help but that’s not what I’m looking for, unless I was doing it wrong…. Think of it as I’m wanting a preloaded spring feel, or a linear spring. Almost center detent like without the bump… does that make sense

[

[OR] SerGeant•7/26/24, 3:29 PM

I get it. You don’t want a linear increase in spring load.
So you have to work with custom spring curves. Maybe someone can explain it better. I didn’t use that feature before.

mattback•7/26/24, 5:16 PM

hello there, @walmis when you last requested i send in a video in the debug mode showing the twist grip values, were you able to view the video i sent, and is there anything more that is needed while you work on the latest update to the register size for the twist grip

1142nd_Bama Is there a setting to give more holding power at the central trimmed position? L...

Hiob•7/27/24, 7:30 AM

Put an additional point on the spring curve (symmetrical) and steepen the first part of the curve. That will greatly enhance the initial spring force right from the center (and increase the centering power).

Teeks•7/27/24, 11:50 AM

my rhino is no longer showing up in windows, but it is showing up in ffb configurator

Teeks•7/27/24, 11:50 AM

any ideas?

Teeks•7/27/24, 11:53 AM

(and as a result not showing up in dcs)

Teeks•7/27/24, 11:54 AM

Teeks•7/27/24, 11:55 AM

ahhhhh

Teeks•7/27/24, 11:55 AM

ok, if i disconnect my throttle, it shows up

Teeks•7/27/24, 11:55 AM

obviously an issue with my pc - disregard!

Teeks•7/27/24, 11:56 AM

(or if anyone has any ideas on how to solve this)? all my devices are plugged into the one powered USB hub

Teeks•7/27/24, 12:10 PM

Fixed it. If my logitech 502 mouse was plugged into the hub, it killed the rhino. Bizarre

142nd_Bama•7/27/24, 12:51 PM

I finally discovered this! Only issue is the sick starts oscillating and vibrates if it’s too step, if I could get that sorted that’s what I was looking for!

HHiob Put an additional point on the spring curve (symmetrical) and steepen the first ...

142nd_Bama•7/27/24, 12:51 PM

Wwalmis Try this fix: https://discord.com/channels/965234441511383080/968208779084701716...

AdiSz•7/27/24, 1:34 PM

Thank you, it worked

TTheAmazinGreat Have you tried pushing down the connector hard to make sure it’s seated? A lot o...

Rhino•7/27/24, 1:41 PM

Yeah, I tried everything I could think of

Rhino•7/27/24, 1:42 PM

I've had to buy a virpil grip since that'll work out of the box

1142nd_Bama I finally discovered this! Only issue is the sick starts oscillating and vibrate...

Hiob•7/27/24, 1:48 PM

Don‘t make the incline too steep or too big. And you may need add some dampening/friction to keep it from oscillating on itself.

[

[OR] SerGeant•7/27/24, 3:48 PM

Hey, I got an issue with the y-axis motor. Inflight i just felt an uneven spring force for pull/push (pull weaker than push) It has 2-3 Amps difference for full pull and push. So it’s no imaginary feeling. My understanding of the software is, to manage the power output related to the springforce at a specific deflection?!

Also the X-axis feels more powerful at all at the same gain overall.

Defective motors?

142nd_Bama•7/27/24, 5:16 PM

How do the end stops work exactly? Is 100% the full range of the calibrated range or the 21/22 deg the rhino is capable of? Reason I ask is I was going to remove my 12deg limiter and use end stops to test different throw degrees….

Matei•7/27/24, 5:50 PM

Im having trouble sourcing my own motor as the ones I've found either seem to have the no integrated drivers and they have different specifications than the ones on the vpforce website. Can anyone help me out?

MMatei Im having trouble sourcing my own motor as the ones I've found either seem to ha...

PiNKSH!T•7/27/24, 5:51 PM

if you plan on using any VPforce software you have to use the VPforce motors Walmis provides

Oh, that screenshot was before I loaded the default config. I missed that. Still, after loading the

Similar Threads