that is kind of lame for it being an ED module
that is kind of lame for it being an ED module
NWould be a q for walmis. As it stands currently, doesn’t look like the pov hats come through in the input report we get from the api in TelemFFB.
AIt is early access, and there’s a lot to do, I’m sure it’ll be added at some point
WHave a question about the Configurator "Store Setting" button. After adjusting the various effects to my liking, I then click the "Apply Settings" button and then the "Store Settings" button. Should those settings survive a power down of the stick. If so, mine doesn't seem to be doing that. It is always comes back up with the "factory" settings after a power up.
UPDATE: I did some more testing and it seems that powering down the Rhino (using the power disconnect button) and then restarting my pc, restoring power to the stick and the starting the configurator keeps the last loaded settings. However, when I started my pc and stick after them being powered off overnight, it returned to default settings.
UPDATE: I did some more testing and it seems that powering down the Rhino (using the power disconnect button) and then restarting my pc, restoring power to the stick and the starting the configurator keeps the last loaded settings. However, when I started my pc and stick after them being powered off overnight, it returned to default settings.
RWhere is latest default config. Getting really bad reverberation with ch47 and my stick is going crazy and erroring out. Resetting doesn’t work with button or motor reset. Belt tension is good. It’s definitely something to do with the spring hz setting and natural dampening compensation.
RVery frustrating. I want to start from scratch to see if it fixes it
WI have had something like that happen if I power up the stick with Pot 1 turned to 100% and the spring slider is at 100%
RI always run both at 100 haven’t had issues until latest dcs update.
RI have however had issues with reverb in the past related to changing settings and my 40cm extension
N<configurator_path>\configs\RHINO-defaults.vpconfRAlso my teleffb is having a lot of trouble while in game and staying running when changing settings. it stops responding every few seconds.
Rive had to close it and reopen to make any changes then after about 5 min its becomes unresponsive.
AStore Settings absolutely should store to the firmware and should survive any restart/unplugging of your computer or the device.
Can you be more specific about what settings are not being stored?
Can you be more specific about what settings are not being stored?
A(also probably a good post to continue discussion for in #
support fwiw)
support fwiw)
CHow can I know how far down the wait-list I am? I placed a request in June but did not get it any serial number or anything
AYou can poke the bot, either via DM or / command here
COoof long wait 760 rhinos to go 
Cthanks
SIt goes quickly and sometimes folks will bow out when they're number is up so keep positive Trust me, it's worth the wait!
Trust me, it's worth the wait!WI can't seem to reproduce it now. If it happens again I'll revisit the issue in Support.
MWhat’s the wait time like nowadays for his the motor kit?
Cwhat are people doing to mount this on this off the floor?
TMotor kits from Walmis usually ship within a few days.
S~260 to go.. anybody have an estimate how long does that typically take?
Haverage of ~20 a month I've heared, supposedly half of those queued don't come through in the end
Fwell I got mine pretty much like 5 months ago and have no. 444.
last sent was 663.
that is like 44 per month.
once you are like 200-100 units in front of it it will go fast though
last sent was 663.
that is like 44 per month.
once you are like 200-100 units in front of it it will go fast though
JI'm curious if anyone else has had issues with centering of the sick and what they've done to resolve it? I've had the base for almost a year.
- I've tried balance spring adjustments
- I've tried static force
- tried static force and balance spring together
I have an extension with a decent offset so it's not naturally balanced. Ultimately whatever setting I try, it won't hold a tight center. It's always off, and based on its previous movement direction it's off by a different amount. This causes lots of issues when trimming, especially force trim in helicopters. I've fiddled with this so many times, but I almost never get consistent behaviors. Especially after recalibrating. I'm pretty lost at this point. Any ideas or help would be grateful.
- I've tried balance spring adjustments
- I've tried static force
- tried static force and balance spring together
I have an extension with a decent offset so it's not naturally balanced. Ultimately whatever setting I try, it won't hold a tight center. It's always off, and based on its previous movement direction it's off by a different amount. This causes lots of issues when trimming, especially force trim in helicopters. I've fiddled with this so many times, but I almost never get consistent behaviors. Especially after recalibrating. I'm pretty lost at this point. Any ideas or help would be grateful.
WDid you try balance spring + adaptive recentering?
Jyes, I can't get balance spring to do anything consistent either. Adaptive recentering is a bit slow and throws off the trim.
S
WWhat’s the distance between gimbal centre and grip connector? I’m trying to work out how long of an extension I want to get for my mounting setup that will roughly match my Virpil CM3 with 200mm extension plus Z-extension that adds about another 100mm. Cheers.
![[OR] SerGeant](https://cdn.discordapp.com/avatars/290181622832168961/338cff3e564800fa5a1068e9c25e28f5.webp?size=40)
[Ca. 165mm
RI used balance spring, and the data of centering and added a little bit of a gain curve to the spring effects and now works pretty good. I’m still having issues with my horizontal wigging out when going through ETL so I’ve had to turn my ETL down to like 5% in teleffb
RIt’s really frustrating that my horizontal axis is having these issues, but I’m not sure how to solve it. It even doesn’t on the default config settings.
Ji tried the gain curve. But for what ever reason the stick goes bonkers if I add any amount of gain. It actually destoyed my extension last night the shaking was so violent.
RI also experienced this but was able to just put enough of a dip to improve my middle strength
![[OR] SerGeant](https://cdn.discordapp.com/avatars/290181622832168961/338cff3e564800fa5a1068e9c25e28f5.webp?size=16)
WCheers
V:package: 
RHINO #0664 Has Shipped!
RHINO #0664 Has Shipped!NTelemFFB Update v20240812
General
- TelemFFB window should no longer be placed off screen if the saved location is outside the bounds of the active monitors @FarFutureFox @Grale- Button binds in TelemFFB now support PoV Hats when "use hats as buttons" is disabled in configurator (Thanks Walmis!) @amadeus
DCS
- Added rotor RPM and damage model telemetry for CH-47DCS/MSFS/X-Plane Helicopters
- Added hardware force trim option for pedals. @SerGeant- Can be bound to button from master instance (i.e. joystick)
- Enable "Use buttons from master device" in the feature options
- To bind to a different controller, use the loopback app (and set grip type in pedals configurator to loopback).
JHook update hype
Renovation might actually be done in the next month or 2 then I'll be able to fly on my cockpit
Renovation might actually be done in the next month or 2 then I'll be able to fly on my cockpit
RHow does this option in the F4 special tab interact with the Rhino?
ADefault ffb strength
LMate those settings are a game changer, One of the crew on here suggested settings of 280 roll and 190 pitch. The default of 100% for both in DCS is simply not enough force going to the Rhino. The F4 always felt to slippery, now with the changed percentages its a dream and with heaps of force feedback. Those percentages can go as high as 500% each.
ANah, it’s fine as is
AWhen you add dampener effects in the Rhino software, it makes it a dream
AI think the F-4 simply demonstrates how poor FFB effects are implemented by DCS since they only account for “spring” and nothing else
AOther modules just don’t suffer from it as much
AUpping the FFB gain just creates
unrealistic feedback which, while it can work, isn’t how the stick would feel in the real plane
unrealistic feedback which, while it can work, isn’t how the stick would feel in the real plane
AJust add 30-40% “dampener” instead and you’ll likely have replicated a decent feel of how the bob and bellows feedback worked in the real plane
AThe stick definitely stops sliding around