Hello, my Rhino isnt detecting any button presses of the warthog joystick anymore. Ive tried the joy

Hello, my Rhino isnt detecting any button presses of the warthog joystick anymore. Ive tried the joystick on the original warthog base and DCS detects all buttons but on the Rhino it goes silent.... The Rhino base is responding when there are axis inputs. FYI it went silent mid flight.

RrDk Hello, my Rhino isnt detecting any button presses of the warthog joystick anymor...

Hiob•9/1/24, 6:15 AM

I would assume, either the cable (to the grip connector) broke, or more likely, the cable detached from the socket-mini pcb that is inside the stick connector. I would dismount the grip (+ extensions). Then you can unscrew the socket inside the grip connector and take it out. On the backside there is a cable plugged in (or isn’t anymore). You can just pull out the cable with a pair of pliers and plug it back in.

Unless somebody else has a better idea that is!

walmis•9/1/24, 7:12 AM

Yeah, good call @Hiob, I'd check the the stick connector, maybe the mini socket has disconnected. I'd also lift the leather holder frame, since it's easier to feed the cable into the tube.

HHiob I would assume, either the cable (to the grip connector) broke, or more likely, ...

rDkOP•9/1/24, 10:35 AM

indeed good call... the cable from the mini socket was obstructed so the tension slowly made it disconnect. I pulled on the cable thinking there would be a few cm extra for good mesure and applied pressure on the connector.. next thing you know the inputs started getting detected again. Thanks for the support.

Wwalmis Yeah, good call @Hiob, I'd check the the stick connector, maybe the mini socket ...

Subtile•9/1/24, 1:50 PM

hey there Walmis, did you see my screens from the logs? Maybe some ideas about my problem ? Thanks a lot

Greekbull•9/2/24, 4:53 AM

So I’ve got an issue I can’t figure out. My base seems to be centered in a stick down orientation. I’ve run the auto calibrate a few times and every time it is centering where in shows in this cell pic. Ideas?

GGreekbull So I’ve got an issue I can’t figure out. My base seems to be centered in a stic...

Xaero Zero•9/2/24, 5:06 AM

Did you "apply settings" after calibration ?

GGreekbull So I’ve got an issue I can’t figure out. My base seems to be centered in a stic...

walmis•9/2/24, 5:40 AM

It works as it should. A game has set the trim center to that location as indicated by the blue circle.

Wwalmis It works as it should. A game has set the trim center to that location as indica...

Greekbull•9/2/24, 5:48 AM

Ah ok is there a way to adjust that? I’m in DCS. Feel like I’m flying with a very constant back pressure even when I try and trim it out.

Greekbull•9/2/24, 5:50 AM

This is in the F4 btw

Greekbull•9/2/24, 5:58 AM

Also, DCS was not like this before today. It was perfectly centered. I used a AH-64 profile in here which really seems to fly nicely in the Apache. But after going back to any of my fast jet profiles the trim center is off in the stick forward orientation

GGreekbull Also, DCS was not like this before today. It was perfectly centered. I used a A...

walmis•9/2/24, 6:16 AM

Depends on the aircraft and special settings in DCS... A-10C, F-5 modules have trim displacement forwards for example.
You can search in this discord, there were multiple discussions regarding this topic

Wwalmis Depends on the aircraft and special settings in DCS... A-10C, F-5 modules have t...

Greekbull•9/2/24, 6:19 AM

Ok I’ll try and find it thanks. It’s just odd since I never changed any settings in DCS. Just was making adjustments in Configurator and Telemffb

GGreekbull Ok I’ll try and find it thanks. It’s just odd since I never changed any setting...

Hiob•9/2/24, 8:24 AM

Are we talking woth this offset trim while DCS is running or not? I'm a bit confused. When you want to calibrate the hardware, neither DCS or TelemFFB should be running. Just the configurator. From there, after calibrating -> applying -> saving, the stick should be perfectly centered.

Hiob•9/2/24, 8:25 AM

Then - inside DCS, it depends very much on the airframe. Most old school jets have the stick trimmed forward for level flight at cruising+ speeds. That's normal. Same for Helicopters of course.

Hiob•9/2/24, 8:27 AM

Maybe you confuse the old "non-FFB" return to center trim in the sim, but that was only a work-around for spring centered, non-FFB-Joysticks.

Hiob•9/2/24, 8:30 AM

Basically, for classic joysticks, the logical (simulated) stick position was detached from the physical stick position. That being no longer necessary is one of the perks of FFB sticks.

Henning Piez•9/2/24, 9:41 AM

what does "FBB_Remove Effect" Mean in the Debug Screen?

walmis•9/2/24, 9:45 AM

It's when a game or telemFFB destroys an FFB effect

Henning Piez•9/2/24, 11:03 AM

so no reason to worry of to trobleshoot?

GGreekbull Ok I’ll try and find it thanks. It’s just odd since I never changed any setting...

TheAmazinGreat•9/2/24, 11:31 AM

It’s modeling real life behavior of jets. There is less forward travel because negative G maneuvers are frowned upon. So there is more positive G travel to “roll and pull”.

Kite•9/2/24, 11:48 AM

As I understand it, it's frowned upon by everyone who has ever tried a lot of negative G's.

TTheAmazinGreat It’s modeling real life behavior of jets. There is less forward travel because n...

Greekbull•9/2/24, 3:53 PM

I get that but I somehow messed this up. I know that you need to trim forward travel. I did run the calibrate with Telemffb and DCS on so maybe that's how i messed it up. I could always do that with my Virpil base. I'm just trying to figure out how in the heck I can undo this because even with DCS and Telemffb turned off it's still trying to give me that trim center blue circle way forward which is totally wrong. Is there anyway I can just reset everything?

GGreekbull I get that but I somehow messed this up. I know that you need to trim forward t...

Number481•9/2/24, 4:05 PM

did you inadvertently change the center point using the hardware trim feature? What happens if you press the bound (or bind and press) the reset button?

NNumber481 did you inadvertently change the center point using the hardware trim feature? ...

Greekbull•9/2/24, 4:10 PM

That was it! Thank You!!!

Reed•9/2/24, 4:44 PM

Best customer service of any manufacturer

Hiob•9/2/24, 5:18 PM

@Number481 is the MVP!

Col. Sanders•9/3/24, 5:12 AM

I think I messed up my rhino. When I was moving it on its mount. I dropped it, not very far but it hit hard. When I fly and the buffeting effect turns on it bucks hard and feels out of balance. I had not changed any settings. Tried turning the buffeting effect way down and as long as it turns on it causes the issue.

Col. Sanders•9/3/24, 5:14 AM

I have taken the top off and the gimble looks fine and I can't see anything obvious. I'm hesitant to tear it down further. Without knowing what I am looking for.

Col. Sanders•9/3/24, 5:25 AM

Also found this tip broke.

Col. Sanders•9/3/24, 5:25 AM

Col. Sanders•9/3/24, 5:26 AM

The plastic ring on the inside broke. So it looks like I need a new power supply. Any recommendations for the US?

CCol. Sanders The plastic ring on the inside broke. So it looks like I need a new power supply...

walmis•9/3/24, 5:56 AM

No need to replace the whole power supply (e-waste and all), you can replace only the jack: https://www.amazon.com/s?k=5.5+2.5+dc+plug

Amazon.com: 5.5 2.5 Dc Plug

Amazon.com: 5.5 2.5 dc plug

Wwalmis No need to replace the whole power supply (e-waste and all), you can replace onl...

Col. Sanders•9/3/24, 6:15 AM

I will look into this. Any ideas on the buffeting issues?

CCol. Sanders I think I messed up my rhino. When I was moving it on its mount. I dropped it, n...

Hiob•9/3/24, 6:41 AM

Everything else feels normal? No grinding, no cracking noises etc. ? Can’t think of a reason why only one certain effect could cause issues….. Checked the settings? (in config and telem!)

Henning Piez•9/3/24, 3:46 PM

Telemffb needs an Config file to use the settings.... In the Settings Page I selected a standard profile that should be loaded at startup.... But.... When starting the sim, the stick is passiv... only acts like a spring / Damper.... If I select / load the same profile in the planes dialog the stick comes alive... why?

HHenning Piez Telemffb needs an Config file to use the settings.... In the Settings Page I sel...

Number481•9/3/24, 4:16 PM

I don't fully understand what you are asking. You don't say the sim, but I'll assume DCS.

Taking TelemFFB out of the equation here (all it's doing is pushing a saved profile to the joystick)....

DCS "takes over" the spring effect during startup, this is why your stick goes limp when the sim is loading. It takes ownership of the spring effect and sets the gain to 0.

When you load into an aircraft, the FFB implementation for that aircraft will set the gain of the effect to whatever it should be based on the phase of flight you load into.

When you exit back out to the main menu, the stick generally goes back to a springless state.

Scorpio•9/3/24, 6:12 PM

I have had this on and off since the beginning:

Scorpio•9/3/24, 6:12 PM

Scorpio•9/3/24, 6:13 PM

There is no Sim running and here are my settings

Scorpio•9/3/24, 6:15 PM

Scorpio•9/3/24, 6:16 PM

I can get it to run ok, when I turn down the gain, but in DCS, any periodic effect will kick it off again. Any ideas?

walmis•9/3/24, 6:17 PM

Try reducing "spring strength proportional damping" and you can try lowering the damper LPF to 6Hz

walmis•9/3/24, 6:18 PM

I suspect the 3d printed extension is not rigid enough for high damper gains

Scorpio•9/3/24, 6:20 PM

Thanks for the quick reply! I set "spring strength proportional damping" to 90% and damper LPF to 6 Hz.

Scorpio•9/3/24, 6:20 PM

It is much smoother; I'll give it a run

Scorpio•9/3/24, 6:21 PM

I also had this happen before I added the extension.

Scorpio•9/3/24, 7:52 PM

After a couple hours flying Apache, it seems to have solved it. Thanks @walmis !

frumpy•9/5/24, 5:11 AM

Hi, I am looking for a X-Plane/MSFS airplane, where the autopilot following works well. So far, I am always having increasing oscillation issues. I want to turn on the ALT or HDG knob and see the magic. Does this work for any of you? On which plane?

SuperStrayan•9/5/24, 6:27 AM

Why is my configurator constantly pulling the master gain to 50% for no reason? Has anyone else had this?

SSuperStrayan Why is my configurator constantly pulling the master gain to 50% for no reason? ...

walmis•9/5/24, 6:28 AM

Possibly you could have sliders configured in telemFFB and it automatically sets the configured values. Without further context hard to tell

Hello, my Rhino isnt detecting any button presses of the warthog joystick anymore. Ive tried the joy

Similar Threads

Similar Threads

Similar Threads