Got it so by reducing Vne gain, make ffb think it is faster than as it is, so I can get higher sprin

Got it so by reducing Vne gain, make ffb think it is faster than as it is, so I can get higher spring force gain, right? but I think it is not only speed related I think it is speed + weight related. but anyways as long as we cannot adjust weight, the speed is the key

PokePokeOP•9/10/24, 2:22 PM

I will try

PPokePoke Got it so by reducing Vne gain, make ffb think it is faster than as it is, so I ...

Number481•9/10/24, 2:30 PM

reducing the VNE speed will just steepen slope of the linear force calculation. At a given speed. Here's a ChatGPT graph showing the applied force (vertical dashed lines) at a given speed (horizontal dashed line) given two very different VNE speed set points (458 vs 300).

PokePokeOP•9/10/24, 2:32 PM

got it, will try it

Thanks for the solution.

KKamini Anyone here got experience with Virpils Z-Extension on the Rhino? How does it wo...

Hiob•9/10/24, 5:38 PM

I don’t know about that particular extension, but generally speaking off-center/gooseneck extension aren‘t a problem. You can balance the stick with the configurator (unless the offset is extrem and the grip very heavy - you could probably still balance it, but the constant applied force will heat up the motors I assume). Why should an extension have an effect on the deadzone though? Btw, there is no deadzone on the Rhino by design.

HHiob I don’t know about that particular extension, but generally speaking off-center/...

Kamini•9/10/24, 7:16 PM

Dead zone is a bad way to describe it but basically the springs weren't strong enough to put it exactly in the center on their own. The last 2 degrees I had to push myself.

smitty•9/10/24, 7:25 PM

give it some more spring in the center:

NNumber481 Rudders are completely different, so that would have been a useful data point up...

hexpod•9/10/24, 9:19 PM

Can the user tweak the spring curve for ailerons and elevators according to the aircraft speed ?

smitty•9/10/24, 9:21 PM

yes in msfs/xplane

Hhexpod Can the user tweak the spring curve for ailerons and elevators according to the ...

Number481•9/10/24, 9:22 PM

Not in DCS/IL2.. its all part of the native implementation.

Hhexpod Can the user tweak the spring curve for ailerons and elevators according to the ...

Col. Sanders•9/10/24, 9:23 PM

Are you not getting any of the native feedback? I still never understood what the concern was with the trimming?

KKamini Dead zone is a bad way to describe it but basically the springs weren't strong e...

Hiob•9/10/24, 9:29 PM

Depending on your spring settings, you can have those issues with the Rhino. A long heavy grip emphasises the problem of course.

Piola•9/10/24, 11:28 PM

@walmis sry for the ping, preorders for the MFG rudders FFB kit opened months ago, is there a way to check the order status?

Austringer•9/10/24, 11:46 PM

https://youtu.be/idZGMYDkbeY?si=XzzaPyqO993scVXX

YouTubeFalcons Ledge

VPForce Rhino Force Feedback base Review - Episode 1: First Impress...

Welcome to our first video on the VPForce Rhino Force Feedback base series!

Check out DDrake1984's Reviews here:
https://t3chtronics.wordpress.com/

Here are links to each of the Products featured in the video:

VPForce Rhino:
https://vpforcecontrols.com/
Discord:
https://discord.gg/Z2N8CQ34

If you want to get a discount on the Next Level Rac...

PPiola @walmis sry for the ping, preorders for the MFG rudders FFB kit opened months ag...

FlatSpin•9/11/24, 12:10 AM

can you share the link for the rudder ffb kit? I can't find it.

CCol. Sanders Are you not getting any of the native feedback? I still never understood what th...

hexpod•9/11/24, 12:11 AM

hexpod•9/11/24, 12:13 AM

Bf109 stabilizer at 100% positive and the plane still pitches up. The “Override Trim” feature doesn’t hold the overdriven trim position. That’s the issue

hexpod•9/11/24, 12:42 AM

Ok, I finally understood I think. You just may not to bind in-game stabilizer on the same button as the rhino trim. A nasty overcome but it seems to work.

Col. Sanders•9/11/24, 12:44 AM

I dont use the rhino trim. The in-game works fine with trim following of the stick.

DARRYL•9/11/24, 3:09 AM

I have played IL-2 GB a fair amount, but never (yet) with FFB. As I recall, IL-2 GB can easily double-bind different in-game functions (even opposing ones) to the same input. This can be both good and bad, depending on circumstances. Not saying that is the problem here, but it has caught me a few times in the past so I thought I'd just mention it to be thorough.

CCol. Sanders I dont use the rhino trim. The in-game works fine with trim following of the sti...

PiNKSH!T•9/11/24, 5:18 AM

I have a separate input (trim wheel) for trim in IL-2 GB & I get the same thing with the bf109 full trim & still it pitches up. I think it's just the way the fm & il2 are with ffb maybe?

PPiNKSH!T I have a separate input (trim wheel) for trim in IL-2 GB & I get the same thing ...

Col. Sanders•9/11/24, 5:37 AM

Hmm ya idk I have mine set to a hat switch and primarily fly 109s and never have had issues with trim and my rhino.

CCol. Sanders Hmm ya idk I have mine set to a hat switch and primarily fly 109s and never have...

PiNKSH!T•9/11/24, 5:41 AM

I might try changing from the axis to hat see if that helps.

VPforceBot•9/11/24, 6:09 AM

:package:

RHINO #0685 Has Shipped!

VPforceBot•9/11/24, 6:09 AM

:package:

RHINO #0687 Has Shipped!

VPforceBot•9/11/24, 6:09 AM

:package:

RHINO #0686 Has Shipped!

FFlatSpin can you share the link for the rudder ffb kit? I can't find it.

Piola•9/11/24, 6:38 AM

https://docs.google.com/forms/d/e/1FAIpQLScJy9f571afga-yYYOE5eqiEacWpqE3UigkC1hfQy6szQnN3g/viewform

Google Docs

VPforce MFG FFB Kit Preorder

Enter your details here, so you can enter the queue for the VPforce MFG FFB Kit.
Once the queue progresses I will get in touch with further details.

The kit contains:
86BLF03 or 86BLF04 FFB motor
Large gear + 14T motor pulley
Belt HTD5M 400
Motor mount + fasteners
Assembled wiring
Toe brake connectors to VPforce board
Power supply - 19V 9.5A 18...

PPiNKSH!T I have a separate input (trim wheel) for trim in IL-2 GB & I get the same thing ...

hexpod•9/11/24, 8:22 AM

It’s seems to be the specificity of the Messerschmitt. It’s not a bug it’s a feature so to speak

DDracks Hello 👋, I don't know if I understood your question correctly, but here's my a...

PlaguedRoo•9/11/24, 12:14 PM

Are you using a throw limiter adapter on your setup?

PPlaguedRoo Are you using a throw limiter adapter on your setup?

Dracks•9/11/24, 1:18 PM

Nop ! I use only the settings in the "effects" tab of TelemFFB: Endstop/axis scaling/etc. Not a physical one

Dracks•9/11/24, 1:19 PM

For now, I have a extension of 10cm/my virpil Alpha and the VP Force base

Hhexpod It’s seems to be the specificity of the Messerschmitt. It’s not a bug it’s a fea...

Col. Sanders•9/11/24, 2:30 PM

This is not true. You should be able to trim the stabilizer to get level flight. There might be some very specific power setting, altitude and wind that it is unable to trim properly, but that is not the inherent design. I have been flying all variants of the 109 a couple times a week for the last 9 months and have not had an issue getting trimmed level flight.

PPiola @walmis sry for the ping, preorders for the MFG rudders FFB kit opened months ag...

Ice•9/11/24, 3:17 PM

Check the knowledge base for the FFB mod for the MFGs made by Hiob. I did it to my pedals and it’s incredible.

CCol. Sanders This is not true. You should be able to trim the stabilizer to get level flight...

hexpod•9/11/24, 7:12 PM

In Dcs it’s a documented feature with a lot of discussion about the phenomenon that’s why I assumed it’s similar in Il2.

Please try it again: increase the airspeed up to 550 km/h with stabilizer setting 100% positive. If you take the hand off the stick you should see the nose going up.

hexpod•9/11/24, 7:13 PM

Col. Sanders•9/11/24, 7:28 PM

I will give it a shot and see.

goobernoodles•9/12/24, 12:31 AM

unboxed my new rhino a little while ago - should it have moved/centered once you twist the red power... button thing to the right to release it? I did that with the software running and it seemed like the power might have been having issues.

goobernoodles•9/12/24, 12:33 AM

goobernoodles•9/12/24, 12:34 AM

...doesn't seem normal to me. if someone would confirm, i'd appreciate it

goobernoodles•9/12/24, 12:45 AM

apologies for the hobbit feet

Ggoobernoodles unboxed my new rhino a little while ago - should it have moved/centered once you...

Number481•9/12/24, 1:14 AM

silly question... have you tried pulling and re-plugging the USB after powering on the Rhino? I sometimes see odd behavior with Configurator if I power cycle the device while its running (but I am running 3 devices so its a bit different situation).

Other than that, a common issue is overloaded USB hubs. Try direct attach to PC if you can (if it isn't already).

Do you still feel the cogging in the axis when the power is on or is it smooth?

Also, even if it were properly connecting, with the profile you have set in your video (with master gain at 0), it wouldn't center the stick.

NNumber481 silly question... have you tried pulling and re-plugging the USB after powering ...

goobernoodles•9/12/24, 1:26 AM

i'll give that a shot - it is plugged into a big usb hub with like 8-9 other devices. i'm not really sure what cogging feels like, it's relatively smooth, but i feel some... uhh lumpiness, for lack of a better term? it's nothing like hitting an afterburner detent or anything

goobernoodles•9/12/24, 1:34 AM

direct connected the usb cable to the motherboard/replaced cable while the power was connected. also, the power adapter is going directly into the wall

Number481•9/12/24, 1:49 AM

Yikes…that sounds like either the internal connections to the stop switch are loose or maybe a faulty PS. (Those are my wild guesses). I’ll tag @walmis for you to make sure he sees it.

walmis•9/12/24, 6:04 AM

Yeah, something's fishy here. It tested fine before shipping, so it might be a PSU or an undetected wiring issue. DMd.

kaltokri•9/12/24, 5:37 PM

I want to configure my new MFG Rhino pedals.
Must/Should I rename the "joystick" and change the ID?
How to avoid conflicts with the Rhino base?
Is there a tutorial on how to configure FFB pedals?

Kkaltokri I want to configure my new MFG Rhino pedals. Must/Should I rename the "joystick"...

Hiob•9/12/24, 6:02 PM

Hey, yeah, you need to deactivate one axis in the VP config and give it a different ID and name it Pedals. It is all pretty straight forward.

Hiob•9/12/24, 6:03 PM

There is some tips on setting them up in the knowledge base thread.

Hiob•9/12/24, 6:04 PM

Most important thing is probably that you make sure that you don’t reach max motor current before the stops. Otherwise it is easy to overpower and tilt the motor by strength of your legs.

Hiob•9/12/24, 6:05 PM

In general, don’t overdo it with the spring gain. Keep it at 50% and dial in your other settings. When you are all set, you can increase it slowly to your taste, but make sure you stay below max current at max deflection.

Got it so by reducing Vne gain, make ffb think it is faster than as it is, so I can get higher sprin

Similar Threads