Make sure it's fully powered via DC plug and e-stop switch is on (motors are running), the fans are

Make sure it's fully powered via DC plug and e-stop switch is on (motors are running), the fans are one on the opposite side of the pic and one on the rear.

Mm2times_Could someone please tell me what is the length of the shaft in the vpforce rhin...

walmisOP•10/16/24, 5:00 PM

https://discord.com/channels/965234441511383080/1118790519103967242/1139070730198319184
Here's the drawing

m2times_•10/16/24, 5:04 PM

Thank you! Maybe I should've asked what is the distance from the top to the pivot point - but this should be close enough for my use case

Wwalmis Make sure it's fully powered via DC plug and e-stop switch is on (motors are run...

Blaubär | Michael•10/16/24, 5:04 PM

You have to press the switch, then the fans do run. Many thanks for the tip!

Horizon•10/16/24, 7:57 PM

I moved up 100 places in 7 days, this rate is crazy

TonyM•10/17/24, 1:55 AM

If the MFG Crosswind kit would also move, that would be terrific

TTonyM If the MFG Crosswind kit would also move, that would be terrific 🤪🤪

SR-F_Winger_[73]_David•10/17/24, 11:22 AM

There is a Kit already available from @kaltokri thou for the MFGs

SR-F_Winger_[73]_David•10/17/24, 11:23 AM

The @Hiob Kit Made AS a Kit ready to purchase.

VPforceBot•10/17/24, 2:08 PM

:package:

RHINO #0739 Has Shipped!

TeufelHunden•10/17/24, 6:36 PM

I ordered the Rhino's 8020 metal mount. The one side with the 2 bolts is snug to my 8020 but the other side has alot of slop or flex in it. The Rhino will bounce up and down when I stall a plane and it's kind of annoying. I tried placing some small rubber pieces between the metal but it still has slop in it. Should I just try to drill some holes and mount with more bolts? I can't really counter sink is though?

TTeufelHunden I ordered the Rhino's 8020 metal mount. The one side with the 2 bolts is snug to...

Hiob•10/17/24, 7:07 PM

I wrapped some electrical tape around it to have a snug fit.

tanr•10/17/24, 8:01 PM

Related to metal mounts, any chance we can get a metal VKB adapter (gunfighter 4)? Would be great to have the peace of mind with metal. And then I could Frankenstein a VKB grip onto a RealSimulator base too…

*NOB*Aries•10/17/24, 8:02 PM

A little video of me and my son replacing the thread head and installing the throw limiter...

https://youtu.be/Gau9bPVesfY

YouTubegodfreynet

Rhino Broken Thread Head Replacement & Throw Limiter Installation

Performed by my 11 years old wingman, under my supervision...

Music used in video:

Pat and Mat Soundtrack (A JE TO! 1979-1985)

constantine•10/17/24, 11:00 PM

very excited for my rhino to turn up over the last few days - could anyone point me in the direction of a good solution to mount it to a NLR flight seat pro? ive heavily considered just throwing some plywood underneath the seat and bolting the rhino to that but itd be a big pain in the ass so if theres someone that makes a mounting plate for the existing center mount on the seat or has another idea thatd be amazing

TeufelHunden•10/18/24, 8:35 AM

Hello 3d printers Whats the best budget 3d printer I can get I mean dirt cheap? $150.00 or less?

TeufelHunden•10/18/24, 8:36 AM

And would it be junk?

Bob Bushman•10/18/24, 8:41 AM

Could likely find a used ender 3 or something for $100.
Sizeable area but lacks any automation so require learning what craft there is in printing but can definitely achieve great prints with the effort.

TTeufelHunden Hello 3d printers Whats the best budget 3d printer I can get I mean dirt cheap? ...

Hiob•10/18/24, 9:06 AM

hi, a brand new bambulabs A1 mini is just 199,- bucks and far FAR superior to any Ender 3 kind of printer. Seriously don't save 50 bucks and get 20% of the performance.

Arno•10/18/24, 9:54 AM

As a former Ender3 user with an ender 3 for sale my honest advice is: Go for Bambulabs.

Flo-Soft•10/18/24, 10:24 AM

Another vote for Bambulabs (owning a P1S with AMS as my third printer now): Their software is excellent, the handling is the easiest I have seen for years, the automated calibration and filament loading is really a gift, the precision of the prints out of the box is amazing. If you just want to print that's the way to go.

TTeufelHunden And would it be junk?

TheAmazinGreat•10/18/24, 10:44 AM

Not necessarily, don’t let the Bambu snobs naysay a good old Ender3.

TheAmazinGreat•10/18/24, 10:44 AM

That being said I don’t think an Ender3 is even sub $150

WhiteHawk77•10/18/24, 11:30 AM

Another plus one for a Bambu Labs, just got a P1S myself, but I hear the A1 is good too.

And TheAmazingGreat, all I keep seeing is people complaining about Ender 3’s online, and basically now they’ve moved to a Bambu Labs printer they can finally start getting over the PTSD the Ender 3 gave them and now spend more time printing than tinkering and fixing stuff with the printer.

VPforceBot•10/18/24, 11:36 AM

:package:

RHINO #0740 Has Shipped!

VPforceBot•10/18/24, 11:36 AM

:package:

RHINO #0741 Has Shipped!

VPforceBot•10/18/24, 11:41 AM

:package:

RHINO #0742 Has Shipped!

WWhiteHawk77 Another plus one for a Bambu Labs, just got a P1S myself, but I hear the A1 is g...

TheAmazinGreat•10/18/24, 11:43 AM

“I’m looking for my first car, I don’t have a big budget.”

“Bro buy a Ferrari, it’s so nice.”

TTheAmazinGreat “I’m looking for my first car, I don’t have a big budget.” “Bro buy a Ferrari, ...

WhiteHawk77•10/18/24, 11:49 AM

Someone already mentioned the A1 mini, I think that’s made by Bambu Labs.

Hiob•10/18/24, 12:34 PM

There is nothing per se wrong with an Ender 3. It is just not state of the art anymore. The manual bed leveling alone is a show-stopper today (before I got a Prusa MK4 for the office and later an A1 mini for private, I used an Ender 3 for a couple of years).
If we were talking a big gap in money for a modern printer - of course an Ender is fine. You will get your stuff printed. Very slow, and not dimensionally perfect but still.....
....but as I said - a brand new A1 mini is just 50,- bucks over the budget given by @TeufelHunden . If that's a hard limit - well I would look for a used A1-mini. But honestly it would be wiser to find the 50,- bucks somewhere.

Hiob•10/18/24, 12:36 PM

Of course an A1 mini comes with one shortcoming - It has only 180 bx 180 build plate. But I can count on one hand the times I needed more than that in the past couple years.

TTheAmazinGreat “I’m looking for my first car, I don’t have a big budget.” “Bro buy a Ferrari, ...

Hiob•10/18/24, 12:38 PM

The cheaper bambu options are for sure close to a ferrari in speed, but certainly not in price. So, no..... not a valid point.

Fierce_Fire•10/18/24, 12:41 PM

The reason people advocate for bambu over ender is that its a lot less hassle. Sure, you can print decent things with a 150 dollar printer, but those will take time to set up and dial in. A bambulab(there are others but its just the best) is well tuned out of the box and you can instead focus on printing.

Fierce_Fire•10/18/24, 12:43 PM

It'd make the comparison between a beaten up older car and a new cheap one. Sure, you might be able to get the first car for cheaper, but itll require a lot more maintenance than if you save up for a brand new one.

Fierce_Fire•10/18/24, 12:43 PM

And in this case you also get much better performance out of the newer model

TTeufelHunden And would it be junk?

Fierce_Fire•10/18/24, 12:50 PM

So, to answer the question, yes, an ender 3 would likely be possible for that price, and itll print what you want it to. Just know that itll take time to set up and dimensional accuracy and speed will be worse than the bambu a1 mini

Fierce_Fire•10/18/24, 12:50 PM

Which isnt to say that you cannot print anything well on it, but the reason people recommend saving for bambu is that its just that much better

WWhiteHawk77 Someone already mentioned the A1 mini, I think that’s made by Bambu Labs. 🙄

TheAmazinGreat•10/18/24, 1:03 PM

He asked for under $150 and no one, including me with the Ender3 suggestion, has given a recommendation that fits his criteria.

TheAmazinGreat•10/18/24, 1:04 PM

There are also plenty of problematic things about the closed Bambu ecosystem too.

TTheAmazinGreat He asked for under $150 and no one, including me with the Ender3 suggestion, has...

Hiob•10/18/24, 1:12 PM

Sure. The point is you can get something really good for 200,-. Recommending something far inferior for 150,- would simply be bad advice.
Sometimes the best advise is: Don't do it, save some more.
You can have a different opinion, thats fine, But is seems a broad consensus.

Hiob•10/18/24, 1:13 PM

Also @TeufelHunden is free to discard the advise if he doesn't find it helpful....

TheAmazinGreat•10/18/24, 1:30 PM

Far inferior is subjective, that’s my point and I’m sticking to it. I defend Ender 3 because I’ve spent the time to dial it in and it works great. Bambu user defend their printers because they spent the money and it works great.

TheAmazinGreat•10/18/24, 1:30 PM

Both work great, but some have abundance of time, some have abundance of money. Rare that anyone has both these days.

Col. Sanders•10/18/24, 1:56 PM

I have no horse in the race, as I don't 3d print. But as a neutral 3rd party you seem to be the only one defending something because it's what you purchased. The others are giving valid advice. Saving up another $50 seems 100% the right call. Although at the budget amount, $50 is a large percentile increase, it should be doable for any that can afford to buy or build a rhino.

TheAmazinGreat•10/18/24, 2:06 PM

Everyone is defending based on what they purchased. In my opinion negative points brought up about Ender 3 are invalid but that’s because I have experience that says otherwise.

TheAmazinGreat•10/18/24, 2:08 PM

My Ender 3 experience is that I get as good as quality prints as Bambu and I saved money.

tanr•10/18/24, 2:29 PM

Most new users are going to waste a bit of material learning a new printer. One more cost to consider as part of this.

TTheAmazinGreat Far inferior is subjective, that’s my point and I’m sticking to it. I defend End...

Arno•10/18/24, 3:40 PM

Coming from years with an Ender, I am not looking to bash it. But especially if you are new to 3D printing, just so much time goes into learning how to set up things right. And when you want to go to PETG, even with experience you end up with misprints regularly, you spend time troubleshooting. And in the end you will spend money on upgrades. Just the money I spent to make it more quiet. $150 is a tiny budget to spend on a printer, so you have to make concessions somewhere. I think spending a bit more on a Bambu will save loads of time and frustration.

TonyM•10/18/24, 4:30 PM

So a Bambu is like a Prusa in terms of quality and maintenance but cheaper, correct?
(using a Prusa MK3S+ the last 2.5 years)

Sudeebare•10/18/24, 4:51 PM

This talk is all about hardware, but how does one learn what is needed to use the hardware. For instance, if I want to find and use files for belt covers for the Rhino's exposed belts, what is the workflow?

Flo-Soft•10/18/24, 5:15 PM

Basically a bunch of reading, watching youtube videos and doing a lot of trail and error...

Simplified workflow:
1. Setup printer for the desired filament type (normally there are instructions doing some test prints to decide what parameters to use for temperature, flow rate...). This has to be done once and can be used for further printing
2. Get a description file for the object to be printed. This is normally an STL file. You can create such a file by using CAD software by yourself (FreeCAD, Fusion 360,...) or somebody else already provides this file.
3. You need to define printing parameters for the object like how strong are bottom, top and walls, percentage of infill,... to define how strong the object will be. If somebody alread provided the STL files there are normally recommendations which settings to use.
4. Translation of the STL file to printer specific GCode. This can be done by a program called Slicer. There are several available, normally there is one favourite for each printer brand to be used (Bambu/Orca Slicer, Ultimaker Cura...). In the Slicer you import the STL file, place it on the (virtual) printer plate (orientation can be important), set the parameters defined in step 3 and slice the project. The resulting GCode can be sent to the printer (newer ones using WLAN, older ones USB stick or memory card).
5. Start printing, then wait and hope everything is running smooth...

TTonyM So a Bambu is like a Prusa in terms of quality and maintenance but cheaper, corr...

Flo-Soft•10/18/24, 5:27 PM

I think I can agree to that. Bambu Lab printers were originally in almost the same price range as Prusa, but this summer they celebrated some anniversary and did a massive price reduction (maybe there are also some new models in the pipeline). There is an intersting video of a printer farm owner comparing Prusa and Bambu: https://www.youtube.com/watch?v=x_Esrxt7GII

YouTubeShop Nation

3D Printer Reliability: Prusa vs. Bambulab

Start your free trial with Shopify today by heading to https://shopify.com/shopnation
Visit the Shop Nation Store: https://shopnationstore.com

(early) Black Friday Sale!
Bambulab P1P - https://bit.ly/3O2SLFy
Bambulab P1S (with enclosure) - https://bit.ly/44D99Ub
Bambulab X1C - https://bit.ly/450GVCV

Prusa mk3S+ - https://bit.ly/3Qb1jMI
Prusa m...

Make sure it's fully powered via DC plug and e-stop switch is on (motors are running), the fans are

Similar Threads

Similar Threads

Similar Threads