Modified gain maps for damping, that make it change quickly near the center, have also caused oscill
Modified gain maps for damping, that make it change quickly near the center, have also caused oscillations for me.
TNo problem!
RWhich way on the map caused oscillation with reference to dampening?
TA steeper vertical slope near the center. Shallow angles were okay.
LHello everyone, hello to @walmis and @Number481
I received my Rhino base in June 2024 but with the death of my father-in-law, then solve all the problems and well I had not been able to play with my #Rhino.
I finally have time to play with it. I'm here to bother you to solve a problem! I drive on #Dcs /IL2 Bob and Mfs 2020!
My #rhino is well recognised by my Windows 11pro/Amd 7800x3D/64 ram ddr5/Mobo-Asus B650E-E ROG STRIX/ RTX 4090/Pimax Crystal Headset /MFG rudder. I launch the 2 Rhino apps (VPFORCE Configurator+Telem FFB) I use the #Rhino configuration (default rhino), I didn't change anything! Everything works very well apparently. My problem is that my Rhino, when I push/pull it towards me, everything works very well with a resistance in flight but: Laterally? My #rhino from left to right is all soft? I don't understand at all?
I received my Rhino base in June 2024 but with the death of my father-in-law, then solve all the problems and well I had not been able to play with my #Rhino.
I finally have time to play with it. I'm here to bother you to solve a problem! I drive on #Dcs /IL2 Bob and Mfs 2020!
My #rhino is well recognised by my Windows 11pro/Amd 7800x3D/64 ram ddr5/Mobo-Asus B650E-E ROG STRIX/ RTX 4090/Pimax Crystal Headset /MFG rudder. I launch the 2 Rhino apps (VPFORCE Configurator+Telem FFB) I use the #Rhino configuration (default rhino), I didn't change anything! Everything works very well apparently. My problem is that my Rhino, when I push/pull it towards me, everything works very well with a resistance in flight but: Laterally? My #rhino from left to right is all soft? I don't understand at all?
LMy #Rhino is connected to a Hub -USB 3.0 self-powered with an electrical outlet and connected to a USB-3.0 socket on my motherboard!
But nothing works!!
From left to right there is no force, or FFB?
Did I miss something?
I'll put you some screenshots of my settings, it's basic setting.
I leave as a noob #FFB with this #Rhino, my only joy FFB is a logitech G960 and à Microsoft #Sidewinder II ,there a long Time (1999).
Thank you in advance for your help and the delivery of my #Rhino last June.
But nothing works!!
From left to right there is no force, or FFB?
Did I miss something?
I'll put you some screenshots of my settings, it's basic setting.
I leave as a noob #FFB with this #Rhino, my only joy FFB is a logitech G960 and à Microsoft #Sidewinder II ,there a long Time (1999).
Thank you in advance for your help and the delivery of my #Rhino last June.
L
L
L
L
LThank you so much in advance .
LLaurent /
WThe X motor has shutdown due to instability, try reducing
To reset motors click Debug tab -> Reset Motors button
Both motors should have status OK at the bottom.
damper force LPF5-6HzTo reset motors click Debug tab -> Reset Motors button
Both motors should have status OK at the bottom.
L@walmis
Hello .
Thank you so much
Hello .
Thank you so much
LI'll try right away with your advice
L
L@walmis
A small question :
-You have to create new profiles to adjust our Rhino ?
Because when I read the gamers who show their #Setting profile right here ,they have completely different settings from the #default config profile?
Thank you so much .
Laurent /
A small question :
-You have to create new profiles to adjust our Rhino ?
Because when I read the gamers who show their #Setting profile right here ,they have completely different settings from the #default config profile?
Thank you so much .
Laurent /
Si like that your stick returns smoothly at center. how did you achieve that?
DJust finished my build.
Unfortunately i get the following:
"[17:24:06.018] * USB Connected
[17:24:06.029] Motor 0 timeout
[17:24:06.029] Motor 1 timeout"
both motors appear offline.
They have power. I get see them both having green flashing led.
Unfortunately i get the following:
"[17:24:06.018] * USB Connected
[17:24:06.029] Motor 0 timeout
[17:24:06.029] Motor 1 timeout"
both motors appear offline.
They have power. I get see them both having green flashing led.
FMy guess is that applying some damper helps.
FBesides their power cables did you connect their data cables too?
Dyep
FA picture of the board may help. I'd try disconnecting and reconnecting the data cables in both the motors and board just to make sure they are connected correctly.
DTy. Give me some time to unscrew the front cover
DDid that and one of them worked. But the other one is still offline. seems that the connectors are a bit loose
DWell, it seems that the jst pins inside the connector had moved slightly outwards. i fixed the connector and now it works ok.
DThanks
L@walmis
Thank you so much ,
my Rhino work very well ,I Apply /6hz in #Expert Settings -Damper Force LPF
Thank you so much ,
my Rhino work very well ,I Apply /6hz in #Expert Settings -Damper Force LPFDI have another issue, trying to do the first calibration.
I'm with protomaker's design.
In the pdf it says:
(with the stick centered - i'm using the centering tool)
------
My process is as follows:
X,Y values are all 0
I push "Auto Calibrate"
X,Y values become the following:
Xmin=14, Xmax=14
Ymin=1171, Ymax=1172
raw_x=14, raw_y=1172
I set X,Y values as:
Xmin=0, Xmax=4096
Ymin=0, Ymax=4096
I push "Auto Calibrate" again
Apply Settings and Store Settings
raw_x and raw_y on the left panel haven't changed.
raw_x = 14 and raw_y=1172
and the joystick indicator has the dot somewhere in the top left range
I'm with protomaker's design.
In the pdf it says:
(with the stick centered - i'm using the centering tool)
- Click "Auto calibrate"
- In the axes setup set Xmin,Ymin=0 Xmax,Ymax=4096
- Click again "Auto calibrate" and then "Apply settings" and "Store settings"
------
My process is as follows:
X,Y values are all 0
I push "Auto Calibrate"
X,Y values become the following:
Xmin=14, Xmax=14
Ymin=1171, Ymax=1172
raw_x=14, raw_y=1172
I set X,Y values as:
Xmin=0, Xmax=4096
Ymin=0, Ymax=4096
I push "Auto Calibrate" again
Apply Settings and Store Settings
raw_x and raw_y on the left panel haven't changed.
raw_x = 14 and raw_y=1172
and the joystick indicator has the dot somewhere in the top left range
FAfter auto calibrate I click store settings not apply settings.
FAnd remember to move the stick to the max positions after hitting auto calibrate.
FAnd then once you move the stick to the max positions you hit store settings.
Dso i remove the centering tool during the process? in the pdf it says to do that afterwards
DI'll try again like you say
DStill doesn't work.
DIf I alter the X,Y min max values to 0 and 4096
raw_x and raw_y values become like i said
raw_x and raw_y values become like i said
DIf i don't and just push Auto calibrate once, move the stick to max positions and click again, then joystick indicator is correct but still raw_x and raw_y are not 2048 at the center and values are way off the 0-4096 range
FYou don't need the centering tool. Just remove it. Select auto calibrate. Move the stick to its maximum making circles or squares and then select store settings.
FDon't worry about the values. Just make sure it works.
FI never had to enter any values manually. I just did a couple of auto calibrations and then it was ready.
Dwhat about this part of the manual?
FI honestly didn't do any of that. Just a regular auto calibration a couple of times and it worked.
DThank you. I'll do it that way for the time being, but if anyone knows please give me an update.
@Subsonic (Protomaker) Is it something that should be updated in the manual? I'm following the instructions line by line.
@Subsonic (Protomaker) Is it something that should be updated in the manual? I'm following the instructions line by line.
FOnce it is calibrated you don't need to do it again. It's set and ready to go
DI'm still curious though 
LHi @Dimitris
I’m a noob as you with my #Rhino
I Read too the Manual PDF.
For have Axes:
Click in :
-Vpforce FFB Configurator / Settings / import /Rhino-defaults.vpconf and you click = open here
I’m a noob as you with my #Rhino
I Read too the Manual PDF.
For have Axes:
Click in :
-Vpforce FFB Configurator / Settings / import /Rhino-defaults.vpconf and you click = open here
L
LAnd you going in #Settings/ click : Apply setting.
In Vpconfigurator /Settings /Damper Force LFP/ change 8Hz to 6hz .
In Vpconfigurator /Settings /Damper Force LFP/ change 8Hz to 6hz .
LAnd it’s all
L
L