Hi. I'm getting this message when I try to set a config for an aircraft. I can only set the Joystick

Hi. I'm getting this message when I try to set a config for an aircraft. I can only set the Joystick, when I click on Pedals or Collective it won't let me set a config with this message.

TTrigaNZ Hi. I'm getting this message when I try to set a config for an aircraft. I can o...

Number481•11/3/24, 3:09 AM

Open the individual instance windows and do it from there. I’m not sure setting the profile overrides across instances (or things like button bindings) will work from the offline editor.

Number481•11/3/24, 3:10 AM

The offline editor is in need of an overhaul.

TeufelHunden•11/3/24, 3:26 AM

I'm going to order some more throw limiters but I'm a bit confused as to the degree's of movement. I first ordered the 11 degree default but felt like I needed more throw so I ordered the 20 degree and now I have to much throw. When I order my next set I want to order less throw on the nose up pitch and a little more for the nose down pitch. Was the 20 degree that ordered both ways - and + 20 X and Y or was that just 20 total? like +10 -10 on the X and Y? I need to know this so when I place the order for the next set I don't mess up and get totally the wrong size.

NNumber481 Open the individual instance windows and do it from there. I’m not sure setting...

TrigaNZOP•11/3/24, 3:31 AM

Until the last update I've always done it like this. What do you mean "Individual Instance"? It seems not to matter what I click, Joystick remains as the Master Instance. Have tried with DCS running still won't work.

TTeufelHunden I'm going to order some more throw limiters but I'm a bit confused as to the deg...

f14billy•11/3/24, 6:19 AM

What I do is I play with the end stops settings until I find the throw I want. Then I apply those percentages to the 22 degrees of throw and that's the limiter I order.

f14billy•11/3/24, 6:20 AM

The 20 degrees that you ordered is 20 forwards and 20 backwards (+-) so 40 degrees in total.

Ff14billy What I do is I play with the end stops settings until I find the throw I want. T...

TeufelHunden•11/3/24, 6:31 AM

so does this make sense that I order this more more push less pull and a little less roll throw I would like to order some more throw limiters. I would like to order 3.

X +/- 15 and Y -11 +20
X +/- 16 and Y -11 + 20
X +/-17 and Y -11 + 20

TeufelHunden•11/3/24, 6:31 AM

I used the 11 on bottom and 20 on top and liked it for pitch but I want a little less roll so I ordered 3 throw limiters

f14billy•11/3/24, 6:34 AM

Those make sense and you mean less roll not yaw.

f14billy•11/3/24, 6:34 AM

And more push or more pull those are reversible so you can flip them over to experiment if needed.

f14billy•11/3/24, 6:36 AM

But again. I'd test those with the end stops before ordering so you can see if you like the results or not.

TeufelHunden•11/3/24, 6:55 AM

ok that makes sense right now I dont have the end stops on but I did mess with the axis scaling

TeufelHunden•11/3/24, 6:55 AM

so at 75% I would want to order -15 for the nose up pitch

TTrigaNZ Until the last update I've always done it like this. What do you mean "Individua...

Number481•11/3/24, 1:04 PM

Window menu->show child instance windows.

Additional checks were put in the latest release to prevent accidental selection of a profile that changes the PID or device name. Doesn’t appear it is properly accounting for the device configuration context.

NNumber481 Window menu->show child instance windows. Additional checks were put in the ...

Old Prospector•11/3/24, 3:03 PM

Ya mine is still unrecognized in Windows/game

TTeufelHunden I'm going to order some more throw limiters but I'm a bit confused as to the deg...

tanr•11/3/24, 5:02 PM

You can calculate the throw with math. Measure the distance from the center of rotation to the top of the grip (or center of your hand) - that will be your radius, R.
Then 2 x 3.1416 x R = total circumference C. Multiply C by the limiters’ percents from opposite sides (say 11 pull and 20 push for pitch = 0.31) and you’ll have the throw distance. (Edit to fix Discord format changing formula...)

Ttanr You can calculate the throw with math. Measure the distance from the center of ...

Reed•11/3/24, 5:59 PM

I used chatgpt to manage my throw distance per degree based on my setup, let it do its calcuations then had it spit out a graph showing different throw differences per degree, picked what i wanted and printed it in PLA plus, perfection.

Reed•11/3/24, 6:03 PM

Here’s a simplified representation of the data for total throw length at different degree limiters:

Total Throw Length for Different Degree Limiters:

Limiter Angle (Degrees) Total Throw Length (inches)
6 ~5.52
7 ~6.44
8 ~7.37
9 ~8.29
10 ~9.21
11 ~10.13

Description:

• X-axis (Limiter Angle): The angle of the throw limiter, ranging from 6 to 11 degrees.
• Y-axis (Total Throw Length): The corresponding throw length in inches for each degree.

tanr•11/3/24, 6:09 PM

That works!

Reed•11/3/24, 6:14 PM

that is for my length extension

tanr•11/3/24, 9:00 PM

I've been experimenting with which USB ports the Rhino is plugged into. With some ports it will turn itself off (even though USBLogView doesn't show it disconnecting) and TelemFFB console shows it as not connected after an Exception. I thought this was probably related to hitting a limit for USB resources but I don't get any errors about that. I can work around this by choosing the ports and/or hubs it DOES work on, so I have a workaround, but I've noticed some odd details and wanted to check if something else might be going on.

Looking at USB Device Tree Viewer, I see the Rhino's top level node as "Taiwan OEM - OBSOLETE VPforce Rhino FFB Joystick". Does this mean that possibly the correct drivers for it aren't running?
With one of my USB hubs (Startech industrial 3.0 10 port hub w/ 65 watt power adapter) plugging in the Rhino (or booting up with it connected) to that hub (or sometimes a different 3.0 hub) will cause either one or ALL of the devices on that hub to disconnect. They then sometimes reconnect, and sometimes stay disconnected. Think this is just a hub issue, or could something else be going on?
I can connect the Rhino USB directly to a USB port on a PCIE card if that might help, but that would mean extending an already long USB cable from 8 feet to 12 feet - though I can maybe use an extra VR headset USB fiber optic cable. Long cable to mobo pcie usb okay?

Dudeman•11/4/24, 12:02 AM

stupid question. Is there an easy way to update an older build of the VPforce configurator software? Or does it require a new install

Old Prospector•11/4/24, 12:21 AM

configurator just runs the .exe doesn't it

Old Prospector•11/4/24, 12:21 AM

like you just run the new one

Dudeman•11/4/24, 12:26 AM

yeah but then it deletes all my old settings

Dudeman•11/4/24, 12:33 AM

nevermind i got it. I had the wrong firmware

Ice•11/4/24, 1:07 AM

https://i.imgur.com/WEYvlQy.png

Imgur

Ice•11/4/24, 1:08 AM

Happened when I updated

Ice•11/4/24, 1:09 AM

It flagged the updater.exe too.

Old Prospector•11/4/24, 1:36 AM

anyone else have problems with the rhino appearing as a game controller in windows? connects fine to web tool and configurator.

Ttanr I've been experimenting with which USB ports the Rhino is plugged into. With so...

Old Prospector•11/4/24, 3:28 AM

I have also had some funky USB behavior

IIce https://i.imgur.com/WEYvlQy.png

Hiob•11/4/24, 8:23 AM

false positive (as always). If you are irritated by those, check the file with virustotal.com.

FlowerPot•11/4/24, 9:22 AM

I'm planning to buy a forcefeedback stick in the future, but not right now.

What I am trying to do now is build this because I want a quick release rail system which this offers (if something is better i'm all ears) - https://www.youtube.com/watch?v=VWXf6EsfZ4c

Which requires this - https://virpil-controls.eu/vpc-desk-mount-angled-adapter-mt-50-throttle.html

Only problem is that I use a VKB Gunfighter and a modded Thrustmaster TWCS

I figured asking here would be real good as I'd find some people that are all about that DIY.

To me the options seem to be to:

Make the VKB Gunfighter and modded Thrustmaster TWCS fit the virpil desk mount adapter somehow
2.Change the adapter used, but that would require changing the print files for screw points? Something I don't know how to do.

Any input is greatly appreciated

YouTubeLord Skippy

The Ultimate HOTAS Mount 👌 Virpil Throttel and Flightstick + Elgato...

Easy transition between Keyboard & Mouse, Dual Stick, and HOTAS!

Virpil VPC MongoosT-50CM3 Throttle
Virpil VPC Constellation ALPHA-L/ALPHA-R on VPC WarBRD Base
Elgato Stream Deck

Find a full bill of materials and all print files for free on Thingiverse:
https://www.thingiverse.com/thing:4916920

Mount your Virpil Throttle and Stick to linear r...

VPC Desk Mount Adapter - Throttle

★ Allows mounting the VPC MongoosT-50 Throttles, VMAX Prime or VPC Control Panels to the VPC Desk Mounts
★ Metal Construction

Hiob•11/4/24, 9:39 AM

@walmis I had a problem with the Firmware/VP config yesterday. After DCS crashed, the spring was stuck in "controlled by application". No matter what I did, including restarting config or TelemFFB, rebooting the system - even power cycling the Rhino. Only thing that eventually helped was to re-import a profile. Probably was a very unlikely one-off. Just so you know, in case it happens again....

walmis•11/4/24, 9:49 AM

Probably a stuck effect. Power cycling (the red button) will not clear it. To reset You can either type "reset" into the command prompt in the configurator, unplug-replug USB, or issue reset all ffb effects in telemFFB menu.

walmis•11/4/24, 9:49 AM

Although restarting DCS should clear it too

Hiob•11/4/24, 10:08 AM

Thanks, will try those if it happens again.

HHiob false positive (as always). If you are irritated by those, check the file with v...

Ice•11/4/24, 3:02 PM

I assumed so.

tanr•11/4/24, 5:42 PM

Is the new TelemFFB 20241103 now considered to be non-beta? A little confused since the firmware it requires (1.0.17b3) seems to still be in beta, and same for Configurator, which is at 1.0.17b2. Wondering if there will be an announcement when all 3 are at matching release versions? Or when we have release candidates?

(

(41F) RAFAIR Dave H•11/4/24, 5:45 PM

After about three months of using my rhino with a thrustmaster warthog grip the buttons stopped working mid flight , I was trimming f18 and it just went more and more nose down trim.
In the rhino config app it showed button 14 permanently on which I think was nose down trim.
when I unplugged the grip and replugged back in no buttons show up on app.
Debug shows all FFFFFFFF which I think is gripping not detected,
I had swapped my 3d printed grip adaptor for a metal one about a week before so I removed it and saw that the green wire (clock) was cut but still continuity to the Wallis board.
But to rule this out I rewired the din plug and check continuity against the attatched drawing .
Still no buttons
I replaced grip with a new thrustmaster f-18 grip but still no joy
Have I brick the walmis board and can someone confirm that the drawing attatched is the correct wiring.

(

(41F) RAFAIR Dave H•11/4/24, 5:46 PM

This is looking at top of the din plug

slowmover•11/4/24, 5:52 PM

hey mates. I can see that i have friction enable from telemffb but i do not see springs on telemffb. i am blind? cause VPforce software says Springs controlled by application

Sslowmover hey mates. I can see that i have friction enable from telemffb but i do not see ...

walmis•11/4/24, 6:01 PM

Spring is controlled by DCS

((41F) RAFAIR Dave H After about three months of using my rhino with a thrustmaster warthog grip the ...

walmis•11/4/24, 6:02 PM

You can do a connectivity check with the grip using a multimeter:
https://discord.com/channels/965234441511383080/1145651561578647582/1301275762271457394

CaptainNel•11/4/24, 7:28 PM

If I build one it’s going to have a separate controller for the joystick vs the axes, can I map a separate controllers button for the trim release button?

(

(41F) RAFAIR Dave H•11/4/24, 7:32 PM

@walmis I have done a connectivity check and it confirms to the drawing I listed above checked it three times to confirm

((41F) RAFAIR Dave H @walmis I have done a connectivity check and it confirms to the drawing I listed...

walmis•11/4/24, 7:36 PM

Did you do the diode test? It's a bit different as it shows whether the signal reaches the grip electronics. That will confirm whether there's no issues in the connector itself.

(

(41F) RAFAIR Dave H•11/4/24, 9:22 PM

no was just buzing through thre cable

(

(41F) RAFAIR Dave H•11/4/24, 9:24 PM

how do i do a diode check is it each pin to gnd

((41F) RAFAIR Dave H how do i do a diode check is it each pin to gnd

TheAmazinGreat•11/4/24, 9:31 PM

https://discord.com/channels/965234441511383080/1145651561578647582/1301275762271457394

Hi. I'm getting this message when I try to set a config for an aircraft. I can only set the Joystick

Similar Threads