PGot it thanks!
VIm having some issues with oscillations when using software endstops. I think this issue is new in 1.0.17b, but Im not positive. If I move the stick towards the software endstop (with no other forces being active, or master gain to zero) it can induce oscillations, with or without holding the stick. I tried a few things, like low pass and notch filters, but nothing seems to cure it.
V
DOne of my motor wires power looks like it wasn't crimped enough
DIt slid right out when I tried to put the motor in my housing
D
DWhat size JST connector is it?
SI lost trim in the A1 0 in DCS. I have the trim button properly mapped. I can see the trim button move forward in the cockpit, but my physical stick does not move in the cockpit and trim is no longer working in the A-10. Any ideas what I messed up? It was working, but I tried downloading a different profile. I have since restored my original profile, but trim has not returned. I have confirmed that “sticky” is not selected in any of my spring damper, inertia or friction effects. I also have no trim effects in the F 14 if I go into special options for the F-14 in DCS and uncheck trim, then I can make the trim cockpit indicator move with the trim hat, but with force feedback trim enabled trim does not function in the F-14 either. (For anyone who runs across this issue the solution was to go into the effects tab and check hardware for trim and relaunch DCS and trim effects returned I have since gone back to the effect tab and disabled hardware trim and it is still working in DCS so this may be a possible bug after loading a different profile)
KDoes trim on the A10c move the stick to does it adjusted a trim tab?
SYes, I got it working and now when you press the trim hat, the stick moves forward and back with the trim hat. (Both the virtual stick in the cockpit and the rhino stick.)
GI used the webusb tool to flash my rhino to the latest firmware. Now I'm running into some problems. Is there a way to flash the firmware back to a previous version? Like 1.0.16 I believe. Thanks.
WWhich problems?
HED Forums
Hey, usually when I trim the F-4 the FFB Stick would follow. So if trim nose down for fast cruise, the sticks center position (or force free position) would move forward (quite a bit). However, that doesn’t work anymore. I can see that the trim hat inputs are registered and the bob weight indicat...
VI dont have the F4, but for the F14 you have to enable this in DCS options / special / F14 / use FFB trim implementation
HUnless I‘m blind (not impossible 
) there is no such option in the F-4 special options. And I didn’t change anything there either from when it worked.
Does the trim following still work for you in the Tomcat?
) there is no such option in the F-4 special options. And I didn’t change anything there either from when it worked.Does the trim following still work for you in the Tomcat?
WJust tried free flight on F-4 - trim seems to work fine
WDo you get changing center values ?
HI assume you are using the latest beta versions of all software? Is this with or without TelemFFb running?
Hlet me check…
WYeah, without telemFFB, latest beta
Hgimme a sec
HComputer rebooting to be sure. I enabled a deadzone in VP config. Might that be the issue?
H3%
WThat shouldn't affect it
H
HNo, the center value isn't changing
WDo you have Override trim checked by any chance?
HNo not in the Profile I‘m using for the F4.
HI have two basic profiles. One for fixed wing one for Helicopters, The latter has Trim and trim override enabled. The first doesn’t
WDoes trim work for other DCS modules?
HAs far as I can tell, no. But I‘m not exactly sure which module would be the best to test this.
WSU-25T 
HI‘m sure I messed something up on my end, but I can’t figure out what exactly…..
WPushed a new beta firmware (b5). Found a single case when trim center could be stuck due to hw trim leftovers.
HAwesome, will try immediately!
HNo, unfortunately no change. Sorry.
HWait, after re-connecting the USB it seems to work. Let me double check something.
H@walmis It is working again! Thank you so much! 
It worked after I plugged the Rhino in a different USB port. It kept working though after I plugged it in the original USB-hub again. I can think of two possibilities here. Either the logic board needed a 5V power cycle after the firmware update or somehow the order of how the devices were plugged in the Hub mattered. (I did some cable management lately, so the order may have changed).
It worked after I plugged the Rhino in a different USB port. It kept working though after I plugged it in the original USB-hub again. I can think of two possibilities here. Either the logic board needed a 5V power cycle after the firmware update or somehow the order of how the devices were plugged in the Hub mattered. (I did some cable management lately, so the order may have changed).GThanks for the quick response! Problems wise: trim not working anymore (at all!) especially noticable off course in heli´s. But even F-18 didn´t work when telemFFB was active. Also busy with testing other device (MIGS) which apparently also had an issue when working together with the rhino. That was fixed with a software update from the migs side so I figured that was playing up again. Anyway, I´ll try the new firmware and disconnecting USB when I have some time later. However, would be nice to have at least to possibility to downgrade the firmware..
BIs there a way to roll firmware update back?
Balso after firmware update started having issues with spring force applied momentarily while moving joystick in about center area. In the video clip you can see that sometimes spring force jumps very high for a split second.
Nright click->properties on the EXE for the new configurator version. See if there is an option to unblock the file. This has happened to one person I know of for unknown reasons.
BThank you for an advice. I think I had issue with windows archive extract function. Once I used winrar to extract archive, configurator started working. Still having issues with jerking forces on the joystick. Seems like it happens when joystick crosses zero point on the axis.
GFlashed to the b5 firmware and all working great again, thanks Walmis!
Bsamples.csv1.1MB
WSo yeah, found the issue, but you can fix it on your end, fix the belt position relative to the motor so the calibration is within the 0 .. 4096 range
CIf you are interested in critical issues related to I think firmware, my rhino keeps "crashing". Shutdown chime plays in the middle of flying, and I have to cycle the emergency stop to get it up running again.
Started after I updated the firmware + configurator + telemffb (to WIP version) in order to solve another issue, where I cant run telemffb more than like once, before the .exe stops working and I have to unpack the whole telemffb from the zip again in order for it to run.
My original issue wasnt solved by this so now I have both of these issues
Started after I updated the firmware + configurator + telemffb (to WIP version) in order to solve another issue, where I cant run telemffb more than like once, before the .exe stops working and I have to unpack the whole telemffb from the zip again in order for it to run.
My original issue wasnt solved by this so now I have both of these issues
CAlso, any fix for this issue on the configurator?
I keep having to reinstall so much software constantly because it just stops running, doesnt start, after a while. Both the configurator and telemffb...
I keep having to reinstall so much software constantly because it just stops running, doesnt start, after a while. Both the configurator and telemffb...
