I have the Rhino, like it very much , but during long dogfights, the stick forces just fade away, ho

I have the Rhino, like it very much , but during long dogfights, the stick forces just fade away, how hard would it be to upgrade to the more powerfull motors and install them on my current RHINO?

II/JG7_Moto I have the Rhino, like it very much , but during long dogfights, the stick force...

H145Rotor-Sims•1/14/25, 12:25 PM

If you are planning going to 86 motors you'll need to change the base. It's not that hard.

slowmover•1/14/25, 12:46 PM

I am having trouble with the F-18 the stick can not stay in center and now i can not enable autopilot. Any advises here?

slowmover•1/14/25, 12:47 PM

I increased a little the balanced spring

Sslowmover I am having trouble with the F-18 the stick can not stay in center and now i can...

Rocco Thamanoidis•1/14/25, 1:20 PM

Just give it a bit deadzone and adjust your static force or balance spring until its centered. Also update to the latest build 1.017b12.

Rocco Thamanoidis•1/14/25, 1:22 PM

Thats what I use currently. Note I use the sticky option for Spring, so I can override the ingame ffb, which I have switched off.

slowmover•1/14/25, 2:12 PM

Thanks mate i will try it

Sslowmover I am having trouble with the F-18 the stick can not stay in center and now i can...

f14billy•1/14/25, 2:58 PM

Your pot1 is at 0.8%. If you have it assigned to spring gain then you have no spring force to center it. You can see if it's assigned to something in the settings tab under Pot#1 function.

f14billy•1/14/25, 3:03 PM

Also friction is very high. A screenshot of your settings tab would help.

maleioch•1/14/25, 3:39 PM

which part of the VPForce software acts as a throw limiter for the joystick? Is it the "Endstop" secion?

Mmaleioch which part of the VPForce software acts as a throw limiter for the joystick? I...

f14billy•1/14/25, 3:43 PM

Yes that's the one.

Ff14billy Yes that's the one.

maleioch•1/14/25, 3:44 PM

Can this be set "per aircraft" as well? For example: to bring the A-10 warthog center back.

f14billy•1/14/25, 3:45 PM

You would have to see if telemffb has that setting in the aircraft's profile.

maleioch•1/14/25, 3:47 PM

Okay. So this is "global" in the VpForce but may be doable in telemffb. I'll dig into this. Thank you.

Mmaleioch Okay. So this is "global" in the VpForce but may be doable in telemffb. I'll d...

Number481•1/14/25, 4:08 PM

There are no endstop settings in TelemFFB, but you can use the Dynamic Configurator Profile Assignement feature to push a profile when a specific aircraft is loaded.

Ff14billy Your pot1 is at 0.8%. If you have it assigned to spring gain then you have no sp...

slowmover•1/14/25, 4:51 PM

Sslowmover Click to see attachment

f14billy•1/14/25, 4:54 PM

Maybe static force is getting in the way. I would disable it and then make sure you calibrate the balance spring well.

CaiJ•1/14/25, 5:43 PM

does anyone know why telemffb may not be recognizing or reading inputs from my VKB MCG?

HH145Rotor-Sims If you are planning going to 86 motors you'll need to change the base. It's not...

I/JG7_MotoOP•1/14/25, 5:58 PM

Can I buy a base for when upgrading the motors? Or I need to make it?

II/JG7_Moto Can I buy a base for when upgrading the motors? Or I need to make it?

f14billy•1/14/25, 5:59 PM

@SR-FWinger[73]_David offers the base for the 86 motors already pre assembled

II/JG7_Moto Can I buy a base for when upgrading the motors? Or I need to make it?

H145Rotor-Sims•1/14/25, 6:00 PM

@SR-FWinger[73]_David Get it from him. He makes an awesome base. I physically have one. I just dropped in my 86 motors, did the wiring and done

CCaiJ does anyone know why telemffb may not be recognizing or reading inputs from my V...

Number481•1/14/25, 6:51 PM

grip type in configurator must be set for loopback.
loopback app must be running and set to tie your black-box to your Rhino

CaiJ•1/14/25, 7:15 PM

where is the loopback app located

Fr4Ged•1/14/25, 7:29 PM

In the Rhino configuration app in the drop down list where to chose the type of grip

CaiJ•1/14/25, 7:36 PM

oh ok i thought there was a seperate app you needed

CCaiJ oh ok i thought there was a seperate app you needed

Number481•1/14/25, 7:37 PM

It is a separate app, the exe is in the same folder with the configurator exe.

Fr4Ged•1/14/25, 7:44 PM

Oh, don't mind me then

Number481•1/14/25, 7:55 PM

The RhinoLopback App

Google Docs

VPforce Rhino Manual

VPforce RHINO FFB User Manual Version 0.81 (WIP) Table of Contents 1. Welcome 1 2. Getting Started 3 2.1. Technical Specifications 4 2.2. Physical Setup 5 2.2.1. The VKB Adapter 6 2.2.2. The WinWing Adapter 6 2.2.3. The RHINO Throw Limiter Adapters 7 2.3. Initial Connection and Updating ...

NNumber481 [The RhinoLopback App](https://docs.google.com/document/d/1YL5DLkiTxlaNx_zKHEYSs...

CaiJ•1/14/25, 8:27 PM

thank you

[

[OR] SerGeant•1/15/25, 7:37 AM

Hey,
Since the last update of TelemFFB, the VP configurator behaves very strange.
It takes several seconds till I got the device selection window. And then switching between the devices inside the configuration takes also very long. Sometimes they are not initialized correctly in the configurator.
Can anyone else confirm this problem or can someone help?

[[OR] SerGeant Hey, Since the last update of TelemFFB, the VP configurator behaves very strange...

walmis•1/15/25, 8:15 AM

Sounds like USB driver/hardware related issues - try rebooting

Wwalmis Sounds like USB driver/hardware related issues - try rebooting

[

[OR] SerGeant•1/15/25, 8:18 AM

It’s since several sessions. So many reboots have been inbetween.
Maybe isolating the USBs of the VP force devices leads to a solution.

walmis•1/15/25, 8:27 AM

Is it via USB hub?

Wwalmis Is it via USB hub?

[

[OR] SerGeant•1/15/25, 8:47 AM

Yes.I have a simpit with 11 USB devices.
But I have not changed a thing. It has been running without issues since I first plugged the rhino in. 2 years ago.

walmis•1/15/25, 8:48 AM

It could be various reasons - for example Windows update updated something

Wwalmis It could be various reasons - for example Windows update updated something

[

[OR] SerGeant•1/15/25, 12:34 PM

Found the culprit. An usb cable has been squeezed between two alloy profiles. One wire was cut. So I had the USB error you predicted

HH145Rotor-Sims If you are planning going to 86 motors you'll need to change the base. It's not...

I/JG7_MotoOP•1/15/25, 12:55 PM

Are there any 3D print files of the base for larger motors?

H145Rotor-Sims•1/15/25, 1:01 PM

For the Rhino base. Yeah for sure there is. All the stl etc are on github.

II/JG7_Moto Are there any 3D print files of the base for larger motors?

H145Rotor-Sims•1/15/25, 1:01 PM

Post in the DIY section not support

Blackrat•1/15/25, 7:34 PM

Before I attack stuff, is there a guide to switching the din connector 180 degrees as I am running with the emergency stop at the front and already reversed things in the software. just be nice to fit my TM WH stick

BBlackrat Before I attack stuff, is there a guide to switching the din connector 180 degre...

f14billy•1/15/25, 8:16 PM

Just remove the two screws and there should be enough slack to pull it out and turn it.

ItsPuppy00•1/16/25, 8:39 AM

Hey, looking at grabbing the VKB adaptor, what would the wait time for it to be shipped be like?

Ff14billy Just remove the two screws and there should be enough slack to pull it out and t...

Blackrat•1/16/25, 8:47 AM

Perfect thanks, I was about to do that and thought I would ask JIC

(

(41F) RAFAIR Dave H•1/16/25, 12:08 PM

@Blackrat just be carful when pulling out the din as the other side is a jst conector so ensure that’s seated securely when putting all back together also ensure you don’t trap and nick a wire

((41F) RAFAIR Dave H @Blackrat just be carful when pulling out the din as the other side is a jst con...

Blackrat•1/16/25, 1:55 PM

Already rotated, but I literally pulled it up just enough to rotate 180 degrees without fouling the seating area so never saw a wire or what was underneath. If I have an issue I will strip it down, but tested with my TM grip and all buttons work.

(

(41F) RAFAIR Dave H•1/16/25, 3:16 PM

BigC208•1/16/25, 3:53 PM

Help!

Got the Rhino in yesterday and installed in my simpit. I gave MSFS, DCS working properly. Recognize pitch and roll axis.

BigC208•1/16/25, 3:54 PM

IL2GB on the other hand does not recognize the Rhino axis and I can’t map them in setup.

BigC208•1/16/25, 3:59 PM

Since the other simulators recognize the rhino base it must be Il2 specific. Anyone else here had issues? Solutions?

Blackrat•1/16/25, 4:14 PM

If you cannot see it at all then I think IL2 only sees the first so many controllers plugged in and ignores the rest, maybe you have hit that limit. Its been a few years since I flew it.

BBigC208 Since the other simulators recognize the rhino base it must be Il2 specific. Any...

Number481•1/16/25, 5:04 PM

Blackrat is likely on the right track. IL2 only supports 8 devices and will only see the first 8 that it sees. The order it sees them is seemingly random and likely dependant on in what order the devices were connected to windows. Check this thread on how to re-order the devices that IL2 will see. https://forum.il2sturmovik.com/topic/72473-so-you-went-and-bought-too-many-peripherals/

IL-2 Sturmovik Forum

So you went and bought too many peripherals...

Il-2 supports up to 8 devices. It's possible to exceed that limit, either because you have multiple vjoy devices, have racing gear attached in addition to your flight hardware, or maybe you just went a little wild building your home cockpit. This is a short guide to fixing that problem. If You On...

I have the Rhino, like it very much , but during long dogfights, the stick forces just fade away, ho

Similar Threads

Similar Threads

Similar Threads