Sugar Arrafel
RRCRat Rig Community [Unofficial]
•Created by Sugar Arrafel on 6/4/2025 in #ratos-support
How i can connect humidity sensor to CB1 with Manta M8Pv1.1
I understand how to connect it to the clipper, in principle, but now I can’t make it display on the i2c bus yet
16 replies
RRCRat Rig Community [Unofficial]
•Created by Sugar Arrafel on 6/4/2025 in #ratos-support
How i can connect humidity sensor to CB1 with Manta M8Pv1.1
That's partly why I'm asking how to connect it directly to the GPIO (40-pin connector) and initialize the rPI MCU as an additional klipper device
16 replies
RRCRat Rig Community [Unofficial]
•Created by Sugar Arrafel on 6/4/2025 in #ratos-support
How i can connect humidity sensor to CB1 with Manta M8Pv1.1
This is if you connect to M8P v2.0, and I have M8P v1.1
16 replies
RRCRat Rig Community [Unofficial]
•Created by Sugar Arrafel on 6/4/2025 in #ratos-support
How i can connect humidity sensor to CB1 with Manta M8Pv1.1
Just want to connect it to CB1 GPIO
16 replies
RRCRat Rig Community [Unofficial]
•Created by Sugar Arrafel on 6/4/2025 in #ratos-support
How i can connect humidity sensor to CB1 with Manta M8Pv1.1
Also as HTU21D
16 replies
RRCRat Rig Community [Unofficial]
•Created by Sugar Arrafel on 6/4/2025 in #ratos-support
How i can connect humidity sensor to CB1 with Manta M8Pv1.1
It must be I2C Address 0x40
16 replies
RRCRat Rig Community [Unofficial]
•Created by Sugar Arrafel on 6/4/2025 in #ratos-support
How i can connect humidity sensor to CB1 with Manta M8Pv1.1
I have a HDC1080 i2c module
16 replies
RRCRat Rig Community [Unofficial]
•Created by Sugar Arrafel on 6/4/2025 in #ratos-support
How i can connect humidity sensor to CB1 with Manta M8Pv1.1
16 replies
RRCRat Rig Community [Unofficial]
•Created by skyline131313 on 9/21/2023 in #fix-my-print
First Layer has Lots of Gaps?
Dry in the oven at 50-55 degrees for 6-8 hours, and compare the result. Dry in the oven, or better yet, in a vegetable dryer at 50-55 degrees for 6-8 hours, and compare the result.
41 replies
RRCRat Rig Community [Unofficial]
•Created by skyline131313 on 9/21/2023 in #fix-my-print
First Layer has Lots of Gaps?
It is advisable to always dry plastic, even if it is a completely new spool
41 replies
RRCRat Rig Community [Unofficial]
•Created by skyline131313 on 9/21/2023 in #fix-my-print
First Layer has Lots of Gaps?
AND? The plastic is not particularly dry, and that sachet of silica gel in the package does not solve this problem. If your room humidity is above 50-60%, the plastic will pick up moisture in a matter of hours. As an example, PA6 absorbs moisture in 1-2 hours in a humid climate.
41 replies
RRCRat Rig Community [Unofficial]
•Created by skyline131313 on 9/21/2023 in #fix-my-print
First Layer has Lots of Gaps?
It’s just that water bubbles bubble up into the filament and you get such defects, just dry your filament
41 replies
RRCRat Rig Community [Unofficial]
•Created by Sugar Arrafel on 9/13/2023 in #fix-my-print
Overextrusion after internal top layers
But while I was repairing everything, I think I damaged the PT1000 x) Although I hope it’s just the connector that fell off.
52 replies
RRCRat Rig Community [Unofficial]
•Created by Sugar Arrafel on 9/13/2023 in #fix-my-print
Overextrusion after internal top layers
52 replies
RRCRat Rig Community [Unofficial]
•Created by Sugar Arrafel on 9/13/2023 in #fix-my-print
Overextrusion after internal top layers
Plus, the thermal barrier tube rolled inward, so that the diameter of the upper neck of the tube decreased, as a result, the heating block moved back and forth due to the filament
52 replies
RRCRat Rig Community [Unofficial]
•Created by Sugar Arrafel on 9/13/2023 in #fix-my-print
Overextrusion after internal top layers
The bolts on the Rapido ended up loosening again, the block moved up and down, rose up during retracts, and dropped down when printing large surfaces. At the same time, he didn’t stagger too much.
52 replies
RRCRat Rig Community [Unofficial]
•Created by Sugar Arrafel on 9/13/2023 in #fix-my-print
Overextrusion after internal top layers
A week of checks. And the problem turned out to be quite simple. The answer to everything is Rapido Hotend.
52 replies
RRCRat Rig Community [Unofficial]
•Created by Sugar Arrafel on 9/13/2023 in #fix-my-print
Overextrusion after internal top layers
Ok. I found the root of all problems. That was RAPIDO
52 replies
RRCRat Rig Community [Unofficial]
•Created by Sugar Arrafel on 9/13/2023 in #fix-my-print
Overextrusion after internal top layers
Another update to the problem: the more models on the table, the greater the overextrusion. If you print 1 part, everything is basically fine, but if you print 4 models, everything gets worse.
52 replies
RRCRat Rig Community [Unofficial]
•Created by Sugar Arrafel on 9/13/2023 in #fix-my-print
Overextrusion after internal top layers
essentially extremely strange, because... The rotation distance is, in principle, precisely calibrated.
52 replies