WhatTheFuchs
RRCRat Rig Community [Unofficial]
•Created by rbby258 on 3/2/2025 in #fix-my-printer
Vcore 4 500mm heatbed stopped heating?
ahh ok, thank you!
9 replies
RRCRat Rig Community [Unofficial]
•Created by rbby258 on 3/2/2025 in #fix-my-printer
Vcore 4 500mm heatbed stopped heating?
Ok thank you, but where is it physically located on the printer? I couldn't find anything in the documentation or the printer itself. My heatbad has 2 wires for the thermistor and 2 for the actual supply
9 replies
RRCRat Rig Community [Unofficial]
•Created by rbby258 on 3/2/2025 in #fix-my-printer
Vcore 4 500mm heatbed stopped heating?
I have the same issue. Where did you find the thermal fuse? Is there a way to check this via software?
9 replies
RRCRat Rig Community [Unofficial]
•Created by Helge Keck on 11/28/2024 in #ratos-support
VC4 IDEX Endstop calibration test
that worked! Thank you 🙂
122 replies
RRCRat Rig Community [Unofficial]
•Created by Helge Keck on 11/28/2024 in #ratos-support
VC4 IDEX Endstop calibration test
122 replies
RRCRat Rig Community [Unofficial]
•Created by Helge Keck on 11/28/2024 in #ratos-support
VC4 IDEX Endstop calibration test
But afterwards i only did the reset and did the z-offset
122 replies
RRCRat Rig Community [Unofficial]
•Created by Helge Keck on 11/28/2024 in #ratos-support
VC4 IDEX Endstop calibration test
I had to restart klipper, because the Toolhead was not over the cam and VAOC jumped directly into calibration without moving
122 replies
RRCRat Rig Community [Unofficial]
•Created by Helge Keck on 11/28/2024 in #ratos-support
VC4 IDEX Endstop calibration test
122 replies
RRCRat Rig Community [Unofficial]
•Created by Helge Keck on 11/28/2024 in #ratos-support
VC4 IDEX Endstop calibration test
122 replies
RRCRat Rig Community [Unofficial]
•Created by Helge Keck on 11/28/2024 in #ratos-support
VC4 IDEX Endstop calibration test
122 replies
RRCRat Rig Community [Unofficial]
•Created by WhatTheFuchs on 11/7/2024 in #fix-my-mesh
VC4 500 IDEX initial cold mesh
Do you think I can proceed like this?
14 replies
RRCRat Rig Community [Unofficial]
•Created by WhatTheFuchs on 11/7/2024 in #fix-my-mesh
VC4 500 IDEX initial cold mesh
14 replies
RRCRat Rig Community [Unofficial]
•Created by WhatTheFuchs on 11/7/2024 in #fix-my-mesh
VC4 500 IDEX initial cold mesh
14 replies
RRCRat Rig Community [Unofficial]
•Created by WhatTheFuchs on 11/7/2024 in #fix-my-mesh
VC4 500 IDEX initial cold mesh
Yes, I know what you are saying, but do you pull on the X gantry with the linear rail on it, or do you remove the linear rail to bend the X gantry extrusion?
14 replies
RRCRat Rig Community [Unofficial]
•Created by WhatTheFuchs on 11/7/2024 in #fix-my-mesh
VC4 500 IDEX initial cold mesh
Thanks for the answers. I will try to pull up the gantry even more. Maybe with loose linear rail?
14 replies
RRCRat Rig Community [Unofficial]
•Created by Sky on 11/8/2024 in #fix-my-mesh
Commissioning Mesh - Looking for assistance
I would say try abd pull your X-Axis a bit like statet in other threads. Looks like your gantr is bend
33 replies