Zeke
RRCRat Rig Community [Unofficial]
•Created by rngilligan on 3/28/2025 in #fix-my-printer
moonraker not connecting
Having similar issues myself. not sure if you've gotten it resolved, but trying to have a Higher IP address could help, according to one fellow.
also, have you tried sonar?
4 replies
RRCRat Rig Community [Unofficial]
•Created by Zeke on 4/17/2025 in #ratos-support
Extrude Only Move Too Long error during filament unload macro
interesting note, I'm able to run the macro once and then it buggs. so the amount of extruding changes every once in a while...
3 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
Note on your build sheet: if it starts to wear down (the PEI peels off) ask for a replacement. That’s an older version that the coating didn’t work properly on.
I ran into that a while back
312 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
Can’t wait to have some time to do those mods myself
312 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
Sweeeeeeet
312 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
Now I’m fighting some cura issues (the fact that it just won’t work at all lol) but that’s separate
312 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
Much much better!
312 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
What’s the flap control for? So that the fan can be always on and not have spin up time or something?
312 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
Same boat here
312 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
Super happy for you dude!
312 replies
RRCRat Rig Community [Unofficial]
•Created by tg73 on 10/8/2024 in #fix-my-print
Regular surface distortion pattern towards end of larger first layers VC4
The model is only as good as the modeler
2113 replies
RRCRat Rig Community [Unofficial]
•Created by tg73 on 10/8/2024 in #fix-my-print
Regular surface distortion pattern towards end of larger first layers VC4
One must be able to do it by hand to know their model is accurate ;)
2113 replies
RRCRat Rig Community [Unofficial]
•Created by tg73 on 10/8/2024 in #fix-my-print
Regular surface distortion pattern towards end of larger first layers VC4
Love it my guy.
Entering senior year in mechanical engineering, love to see the things applied
2113 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
A whole other can of worms added
312 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
I can only imagine…
312 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
Noted, will be doing IDEX over the summer I think so that’ll be on my list.
Anybody thought about hollowed out milled steel? Would love to give that a shot too
312 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
I’ll give this a shot
312 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
Ti tube?
312 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
It’s not perfect, but it’s much better. Bed mesh difference is nutty (forgot to get pics, sorry)
I manually soaked by homing, keeping the head in center just a bit above the bed, and bringing the nozzle to 150 and bed to 100. Did so for probably 30 minutes
312 replies
RRCRat Rig Community [Unofficial]
•Created by San_Holo on 4/11/2025 in #fix-my-print
2 months in, Still no good first layer
312 replies