PlastNiklas
RRCRat Rig Community [Unofficial]
•Created by danielk on 1/28/2025 in #ratos-support
Stepper Noise after Update to 2.1.0 RC2
Did you ever solve it?
22 replies
RRCRat Rig Community [Unofficial]
•Created by danielk on 1/28/2025 in #ratos-support
Stepper Noise after Update to 2.1.0 RC2
stealthchop_threshold: 0.1
works for shutting them up while idle. hopefully wont fuck anything.
22 replies
RRCRat Rig Community [Unofficial]
•Created by danielk on 1/28/2025 in #ratos-support
Stepper Noise after Update to 2.1.0 RC2
Realtime analysis is also showing higher amplitude in z signal at idle
22 replies
RRCRat Rig Community [Unofficial]
•Created by danielk on 1/28/2025 in #ratos-support
Stepper Noise after Update to 2.1.0 RC2
Also, z is higher pitch than before. Amp change maybe?
22 replies
RRCRat Rig Community [Unofficial]
•Created by danielk on 1/28/2025 in #ratos-support
Stepper Noise after Update to 2.1.0 RC2
Just got this today updating. Octopus v1.1 F446 and same LDO-42STH48-2504AC steppers. Both Z and AB
22 replies
RRCRat Rig Community [Unofficial]
•Created by Mr_Phelps_VCore_4.0_500 on 4/25/2023 in #fix-my-print
overextrusion on top layers
You may have just saved my ass with that thank you!
9 replies
RRCRat Rig Community [Unofficial]
•Created by Daxxer on 6/25/2023 in #fix-my-mesh
Probed after heating shows upwards bow down the center
This doesn't explain why the mesh is worse at the back and almost straight at the front though.
11 replies
RRCRat Rig Community [Unofficial]
•Created by PlastNiklas on 6/30/2023 in #fix-my-mesh
What should I do about this?
Ya i know
19 replies
RRCRat Rig Community [Unofficial]
•Created by PlastNiklas on 6/30/2023 in #fix-my-mesh
What should I do about this?
Ya
19 replies
RRCRat Rig Community [Unofficial]
•Created by PlastNiklas on 6/30/2023 in #fix-my-mesh
What should I do about this?
Main issue is having to heatsoak every print
19 replies
RRCRat Rig Community [Unofficial]
•Created by PlastNiklas on 6/30/2023 in #fix-my-mesh
What should I do about this?
Interesting...
19 replies
RRCRat Rig Community [Unofficial]
•Created by PlastNiklas on 6/30/2023 in #fix-my-mesh
What should I do about this?
Heatsoak and rail retighten?
19 replies
RRCRat Rig Community [Unofficial]
•Created by PlastNiklas on 6/30/2023 in #fix-my-mesh
What should I do about this?
Really? How did you achieve that?
19 replies
RRCRat Rig Community [Unofficial]
•Created by PlastNiklas on 6/30/2023 in #fix-my-mesh
What should I do about this?
Pretending the only issue is bimetal expansion, that would put gantry in stress at room temp which id assume would eventually slide back into the old position
19 replies
RRCRat Rig Community [Unofficial]
•Created by PlastNiklas on 6/30/2023 in #fix-my-mesh
What should I do about this?
How long ago? Does it eventually drift back?
19 replies
RRCRat Rig Community [Unofficial]
•Created by PlastNiklas on 6/30/2023 in #fix-my-mesh
What should I do about this?
Ya like .375 so imma try retightening linears after a heatsoak. If that doesn't help imma do FDC.
19 replies
RRCRat Rig Community [Unofficial]
•Created by PlastNiklas on 6/30/2023 in #fix-my-mesh
What should I do about this?
Even as a cold mesh? Gonna get worse with heat
19 replies
RRCRat Rig Community [Unofficial]
•Created by PlastNiklas on 5/30/2023 in #ratos-support
Fucky drivers?
Update: I soldered rx and tx together and it works, movement and all, but now the stepper is ticking
2 replies