TheTik
RRCRat Rig Community [Unofficial]
•Created by sidowszy on 4/30/2025 in #fix-my-printer
Thermistor issue with Rapido 2
If the reported value isn't changing though, then it isn't hooked up right. If you had the wrong sensor type, you'd still get a change but it would be an offset and change differently (even backwards).
12 replies
RRCRat Rig Community [Unofficial]
•Created by sidowszy on 4/30/2025 in #fix-my-printer
Thermistor issue with Rapido 2
Do you have
sensor_type: PT1000 in your config? If so, thats correct12 replies
RRCRat Rig Community [Unofficial]
•Created by VascoFaria on 4/17/2025 in #fix-my-printer
MCU unable to connect
I've only ever flashed mine via sd card :/
8 replies
RRCRat Rig Community [Unofficial]
•Created by sidowszy on 4/30/2025 in #fix-my-printer
Thermistor issue with Rapido 2
Since you've got a multimeter, try measuring the resistance when you heat it up.
12 replies
RRCRat Rig Community [Unofficial]
•Created by sidowszy on 4/30/2025 in #fix-my-printer
Thermistor issue with Rapido 2
PT1000 is what tons of us are using, its definitely supported.
12 replies
RRCRat Rig Community [Unofficial]
•Created by sidowszy on 4/30/2025 in #fix-my-printer
Thermistor issue with Rapido 2
Sounds like it isn't hooked up correctly then. If the temp doesn't change at all, I'd double check the pins and wiring
12 replies
RRCRat Rig Community [Unofficial]
•Created by sidowszy on 4/30/2025 in #fix-my-printer
Thermistor issue with Rapido 2
If you hear up the nozzle briefly with a heat gun or lighter, does the temp increase?
12 replies
RRCRat Rig Community [Unofficial]
•Created by Mike C on 4/29/2025 in #fix-my-printer
Issues with firmware on my octopus 1.1
You can try loading firmware via sd card
3 replies
RRCRat Rig Community [Unofficial]
•Created by brian on 4/29/2025 in #ratos-support
temperature_MCU toolhead
ah, yes. If you need to "null" something out then overriding wont' do that
7 replies
RRCRat Rig Community [Unofficial]
•Created by Hercules_119 on 4/29/2025 in #fix-my-printer
Upper belt binding.
Yeah, time to release the belts and see what isn't smoothly turning :/
8 replies
RRCRat Rig Community [Unofficial]
•Created by Hercules_119 on 4/29/2025 in #fix-my-printer
Upper belt binding.
Does it bind at all positions?
8 replies
RRCRat Rig Community [Unofficial]
•Created by brian on 4/29/2025 in #ratos-support
temperature_MCU toolhead
First, shouldn't edit ratos.cfg, override in printer.cfg.
What is the exact error?
And drop your debug.zip in here.
7 replies
RRCRat Rig Community [Unofficial]
•Created by TheTrashPanda on 4/27/2025 in #ratos-support
T1 hotend trouble
No worries, good luck!
26 replies
RRCRat Rig Community [Unofficial]
•Created by TheTrashPanda on 4/27/2025 in #ratos-support
T1 hotend trouble
If I'm reading correctly, this is the macro that is sending that error message
26 replies
RRCRat Rig Community [Unofficial]
•Created by TheTrashPanda on 4/27/2025 in #ratos-support
T1 hotend trouble
What happens if you enter this into the mainsail console?
SET_HEATER_TEMPERATURE heater=1 target=220 ?26 replies
RRCRat Rig Community [Unofficial]
•Created by TheTrashPanda on 4/27/2025 in #ratos-support
T1 hotend trouble
Its just a mainsail button that calls it
26 replies
RRCRat Rig Community [Unofficial]
•Created by TheTrashPanda on 4/27/2025 in #ratos-support
T1 hotend trouble
Pretty sure
26 replies
RRCRat Rig Community [Unofficial]
•Created by TheTrashPanda on 4/27/2025 in #ratos-support
T1 hotend trouble
very odd. I would have thought they call the same macro. Might be worth tracking down where that macro is called by klipperscreen
26 replies
RRCRat Rig Community [Unofficial]
•Created by TheTrashPanda on 4/27/2025 in #ratos-support
T1 hotend trouble
not two T0s?
26 replies
RRCRat Rig Community [Unofficial]
•Created by TheTrashPanda on 4/27/2025 in #ratos-support
T1 hotend trouble
I've never messed with IDEX so I don't know that I'll catch what's wrong, but am looking now. When you ran the configurator you do have T0 and T1 set up, right?
26 replies