connieveren
RRCRat Rig Community [Unofficial]
•Created by connieveren on 3/12/2025 in #fix-my-printer
Controller fan and part cooling fans not working.
This is from the RatOS.cfg file
10 replies
RRCRat Rig Community [Unofficial]
•Created by connieveren on 3/12/2025 in #fix-my-printer
Controller fan and part cooling fans not working.
[fan]
pin: rpi:gpio4 # sacrifical part fan, use this to independently control your both toolhead part fans
[fan_generic part_fan_t0]
4-pin fan connected to 2-pin header on T0 (EBB42 v1.2) - digital pwm
pin: !toolboard_t0:PA0
cycle_time: 0.00004
[fan_generic part_fan_t1]
4-pin fan connected to 2-pin header on T1 (EBB42 v1.2) - digital pwm
pin: !toolboard_t1:PA0
cycle_time: 0.00004
10 replies
RRCRat Rig Community [Unofficial]
•Created by connieveren on 3/12/2025 in #fix-my-printer
Controller fan and part cooling fans not working.
okay thank you. what about the part cooling fans? I can adjust the slider from 0 to 100%, but they dont turn on?
10 replies
RRCRat Rig Community [Unofficial]
•Created by connieveren on 3/12/2025 in #fix-my-printer
Controller fan and part cooling fans not working.
I use a max EZ board and the controller fan is on FAN3 port.
10 replies
RRCRat Rig Community [Unofficial]
•Created by connieveren on 3/12/2025 in #fix-my-printer
Controller fan and part cooling fans not working.
10 replies
RRCRat Rig Community [Unofficial]
•Created by Sait17 on 3/8/2025 in #fix-my-printer
beacon Probe Sample spread too large
I had this problem too, but I didnt have a nozzle on the extruder yet. put one in and the problem was solved. I also tried it when hot and cold, but that didnt make any difference.
3 replies
RRCRat Rig Community [Unofficial]
•Created by connieveren on 2/18/2025 in #ratos-support
Can not open RatOS in the browser
they are the same. The PI is 192.168.1.100 and laptop etc are also on 192.168.1.XXX. I got a monitor end keyboard connected to the pi now and it says: "klipper has encountered an error unknown config object" That might be because I havent updated everything yet?
Also made sure port 22 and putty are allowed through the firewall, but that didnt change anything...
17 replies
RRCRat Rig Community [Unofficial]
•Created by connieveren on 2/18/2025 in #ratos-support
Can not open RatOS in the browser
could this be a SD card problem? since the hotspot from RatOS works?
17 replies
RRCRat Rig Community [Unofficial]
•Created by connieveren on 2/18/2025 in #ratos-support
Can not open RatOS in the browser
Im still waiting for my micro hdmi to hdmi cable to arrive so i can connect a monitor. When trying to ssh into the PI with putty it says "PuTTY Fatal Error: Network Connection Timed Out"
17 replies
RRCRat Rig Community [Unofficial]
•Created by connieveren on 2/18/2025 in #ratos-support
Can not open RatOS in the browser
I also cannot open the IP in the browser. On the router interface it is listed between the devices currently online.
17 replies
RRCRat Rig Community [Unofficial]
•Created by connieveren on 2/18/2025 in #ratos-support
Can not open RatOS in the browser
I just tried Angry IP scanner. RatOS doesnt show up in the list of devices on there, but it is in the list of the router. What could the reason be? On the router it has ip-address: 192.168.1.100
On Angry ip scanner that IP-address is empty
17 replies