CubeMaster
RRCRat Rig Community [Unofficial]
•Created by Loke on 5/14/2025 in #fix-my-print
Anyone experience this?
Also pls use the correct sock on your rapido
It could be that If the Fan Kicks in hard it cools.the Front down
7 replies
RRCRat Rig Community [Unofficial]
•Created by adverse-sapphire on 4/29/2025 in #german-support
Vcore 4 Gantry Twist
Bissel mehr Info wäre nice dann könnte man auch helfen
20 replies
RRCRat Rig Community [Unofficial]
•Created by exotic-emerald on 3/31/2025 in #german-support
Z-Tilt wird nicht richtig ausgeführt
Sind deine Spindeln unten alle richtig fest geschraubt?
13 replies
RRCRat Rig Community [Unofficial]
•Created by optimistic-gold on 3/31/2025 in #german-support
Z-Tilt wird nicht richtig ausgeführt
An Hand der Videos würde ich sagen es wird gemacht...
Bitte Konsole anschauen/zeigen und auch bitte das Bett Mesh dann zeigen
13 replies
RRCRat Rig Community [Unofficial]
•Created by Kinetik on 3/25/2025 in #german-support
Horizontale Artefakte und Beulen in Kanten
Also Error 40 😂 (40cm vor dem Bildschirm)
12 replies
RRCRat Rig Community [Unofficial]
•Created by Kinetik on 3/25/2025 in #german-support
Horizontale Artefakte und Beulen in Kanten
Infill?
12 replies
RRCRat Rig Community [Unofficial]
•Created by Kinetik on 3/25/2025 in #german-support
Horizontale Artefakte und Beulen in Kanten
Und sieht es nur so aus oder zieht es das Teil an den Ecken leicht nach oben?
12 replies
RRCRat Rig Community [Unofficial]
•Created by Kinetik on 3/25/2025 in #german-support
Horizontale Artefakte und Beulen in Kanten
Die Beulen sind PA also Pressure Advance
Inputshaper????
12 replies
RRCRat Rig Community [Unofficial]
•Created by GelberWurm on 2/27/2025 in #german-support
Gelöst: Warum funktioniert mein Drucker nicht? #Unterextrusion #extrusion
Beacon calibrate gemacht?
27 replies
RRCRat Rig Community [Unofficial]
•Created by GelberWurm on 2/27/2025 in #german-support
Gelöst: Warum funktioniert mein Drucker nicht? #Unterextrusion #extrusion
Also Temperatur Zustand (zwecks der Tatsache wie reinigst du deine pei)
27 replies
RRCRat Rig Community [Unofficial]
•Created by GelberWurm on 2/27/2025 in #german-support
Gelöst: Warum funktioniert mein Drucker nicht? #Unterextrusion #extrusion
Wie reinigst du deine pei Platte welche Probe und was für nen Drucker?
27 replies
RRCRat Rig Community [Unofficial]
•Created by mc-iceman on 2/25/2025 in #german-support
Vcore 3.1 Idex Problem nach Firmware Update
Du hast wahrscheinlich den V4 idex angewählt oder? Da musst du nun halt die endstops noch anpassen da der v3.1 nicht so breit ist wie der v4
5 replies
RRCRat Rig Community [Unofficial]
•Created by Heiko on 12/5/2024 in #german-support
Netzwerkkabel am Raspi
Beacon, Board, und toolheadboard mehr würde ich nicht an den Pi packen wenn du ihn übers Octopus betreibst
Würde dir empfehlen nen powerd USB Hub zu besorgen
12 replies
RRCRat Rig Community [Unofficial]
•Created by Poseidonix | Petro on 10/10/2024 in #german-support
extrusionsprobleme
Schau einfach Mal an layer auf layer wie er das setzt ab da wo es etwas gefailt hat
14 replies
RRCRat Rig Community [Unofficial]
•Created by Poseidonix | Petro on 10/10/2024 in #german-support
extrusionsprobleme
Schau dir Mal im slicer das layer stacking an bitte
14 replies
RRCRat Rig Community [Unofficial]
•Created by Poseidonix | Petro on 10/10/2024 in #german-support
extrusionsprobleme
Wenn du die erste Linie in die Luft druckst kann der lüfter noch soviel kühlen.
14 replies
RRCRat Rig Community [Unofficial]
•Created by Poseidonix | Petro on 10/10/2024 in #german-support
extrusionsprobleme
Bei der Vase hier sieht mir das ziemlich nach überhang Fehlern aus
14 replies
RRCRat Rig Community [Unofficial]
•Created by Poseidonix | Petro on 10/10/2024 in #german-support
extrusionsprobleme
Und Schicht höhe?
14 replies
RRCRat Rig Community [Unofficial]
•Created by Poseidonix | Petro on 10/10/2024 in #german-support
extrusionsprobleme
Mit wieviel mm/s hast du gedruckt?
14 replies
RRCRat Rig Community [Unofficial]
•Created by 03Julian04 on 9/24/2024 in #german-support
first layer Probleme
Doofe Frage
Das hotend hast richtig fest geschraubt? Sowie nozzle usw alles hot tighten?
130 replies