vaoc cant finde camera
i havent used my printer for a while. vaoc worked fine a few months ago. so i did all the updates and now vaoc wont conect. i already did a ratos reinstall that didnt help. i can get a picture with mjpeg.
Prusa Einsy Configuration Issues
Hi all, two issues setting up my prusa einsy. Walked through the bootloader procedure as outlines on the Github, however once set up the RatOS running on a Pi3A+ is not detecting the einsy board. The first image relates to getting to the board page and not having a mens to boot load foirmware though the configureator page, i skipped it because i did it via the tutorial. additionally, on the minsail home page i get the error message about the pins. my printer uses the sensorless homing, and i am...
Belt tension graph interpretation help
I generated the belt tension graph after replacing the idlers, belts, and pulleys (They were due for a change) and was wondering how to interpret the graph. I've always used the Gates Carbon Drive frequency analyzer to measure the frequency of a 150mm section of the belt in the past, and it has worked somewhat ok for me. I figured since RatOS comes with a belt tension measurement macro, I should try it out. This is the graph I get. As I understand since the machine is CoreXY, adjusting one belt...
Solution:
That means the upper belt needs a bit more tension.
Perhaps, release just a touch the lower and tighten the upper....
can´t flash Octopus V1.1 - Core-V4 500 IDEX
Hey,
I'm currently building a Core-V4 500 IDEX, the hardware is ready, but I'm failing to flash the Octopus 1.1.
I've already tried a few things, but every time I get the message “Octopus V1.1 detected but is unresponsive” (see picture)
The board has no jumpers and is powered by a 24V power supply. (see picture)...
Merc 1 Hydra RatOs 2.1
I have a odd issue and for the life of me i cannot figure it out, printer was working great but hated the toolhead so i swapped it out to a stealthburner with bambu hotend, did the calibrations for new toolhead beacon heightmap all that stuff, all worked fine, sliced a test cube sent to printer it does its things z tilt, etc but right before it does the adaptive mesh it moves to front left corner and slams into the front profile, then it slowly does a moonwalk to the right likes its doing a purge line but it does nothing, then it moves to right corner then does the scan and back to right corner and does the blob, and prints perfect, i cannot get it to stop slamming into the front rail. i did no changes other than toolhead , i have sized down the bed mesh a lot still does it. has the frabreeko 400mm bed, using orca slicer and copy n paste gcode from ratos set up, nothing added to it
[bed_mesh] horizontal_move_z: 25 mesh_min: 20,80...
[bed_mesh] horizontal_move_z: 25 mesh_min: 20,80...
Chamber heater settings question
I’ve added a DIY chamber heater based on a bath heater.
- I have a temperature sensor on above toolhead 0 (sensor pin PF4);
- a sensor in front of the heater (sensor pin PF5);
- a 12V fan connected to PE5;
- a 40A SSR connected to PA2 and to the heater....
Solution:
CHAMBER_HEATER_ON CHAMBER_TEMP: whatever you want
Extra’s.resonance_tester ERROR
I have updated everything and installed ratOS multiple times, but I still get this error. It’s really frustrating because I’ve been struggling with this for months. Can you please help me solve this?
Solution:
Update everything. Always start with RatOS, then Ratos configuration.
Then restart moonraker, hard refresh on the browser (ctrl+shift+r) and refresh updates. Than update everything else...
ratos-configurator: invalid
I ran into an issue, I can't recall exactly what it was, but when searching here there was an explaination that a bug slipped through and to update to the latest. I went into
Machine and clicked UPDATE ALL COMPONENTS, this seemed to complete, but then I'm left with ratos-configurator invalid. I did some searching and found some information about ratos doctor, I tried running it and got command not found, I searched that and came to this post: https://discord.com/channels/582187371529764864/1329115674215448616/1336836562381570149
I tried those instructions, mainly switching to v2.1.x-deployment branch, however even after that I still get:
```
pi@RatOS:~ $ ratos doctor
-bash: ratos: command not found...Solution:
I reimagined the sd card a little bit ago and am currently installing things in the prescribed order.
Octopus Pro 446 and RatOS firmware not updating
I am on step 2 of the configurator and get the attached error:
"Octopus Pro 446 detected
Warning: Version mismatch
The board is running version v0.12.0-268-g0844388d but you your pi is on version v0.12.0-268-g0844388d7. If you want to update your board click 'flash again' below....
