Bad bed leveling
Hey y'all. I have a reasonably flat bed however my bed leveling doesn't seem to be working as I'd expect. All my probe settings are stock except my X/Y offset which is on the back right of the print head. Probe repeatability reads 5 micron and the printer definitely compensates some amount but clearly not enough. Is there something I'm missing here?
2Prints dont Fit together
So im Printing two base plates they are litreally the same size in the cad software and slicer. Every hole aligns with each other, but Printed they dont fit only the top four holes align with each other. The lower plate does not fit with the topplate. If i flip the lower plate 180degrees then the holes fit. I dont know if im giong mad because ive been awake for 24hours but what is going on ?
gap in Z seam
I have a nasty gap in Z seam.
Things i tried:
3 different slicers.
Set Zseam gap to 0...
Overextrusion at my seams. Motion seems to pause.
I'm working on printing nylon. So I have my speeds dialed down to 60mm/s for the most part. However, it seems like the motion pauses at layer change or retraction and ends up causing a bit of overextrusion. Where is the parameter in Prusaslicer that drives this speed? I've been digging and can't seem to puzzle out which knob needs to turn. 😕
The ripples! Wavy/rippled surface.
Please save me, I am struggling to figure out what this is. The ripples !
I get them when printing slow or fast.
I tried loosening belts and tightening.
...
Volcano Hotend Issue
Hi,
I got an issue with my Volcano. It cannot run at low speed.
Recently I print PETG.
230C, 90% fan. Max flow at 13mm3/s on 0.4 Nozzle (normal, not CHT)
...
underextrusion or other issue
Here's a picture of a pressure advance tuning tower (chosen because it's easier to see the issue). It looks like underextrusion to me how there are little divots in the layers. I haven't tried everything yet, but as I go through more and more calibration procedures it bugs me more and sometimes invalidates the cal.
Any suggestions as to what to focus on?...
Heavy underextrusion on any line break
Hi everyone. I've got V-core 3.1 200mm with ldo orbiter 2.0 and rapido HF hotend. The printer worked fine for a month, but now it has sever underextrusion whenever extruder breaks a line, most prominently on Z seam. I initially thought it's due to pressure advance calibration (I've folloswed Elli's pattern guide for that), but since recalibration didn't help at all I've tried tower method. This is what I get every time I try a print.
My full config can be found here: https://github.com/smumriak/ratrig_bunny_klipper, all my overrides are located in Bunny folder.
Printing with Overture PETG, 0.4mm nozzle, 0.2mm layer height, flow rate 0.96, hotend temperature 240 for first layer, 250 for subsequent, coolying 50%.
I've tried lowering speed, lowering acceleration, decreasing corner acceleration, disabling retraction in slicer and in RatOS files. No change at all....
failed prints only on one side
i have changed the extruder since the last one failed and now all my prints fails on the left side only.
Asking for PrusaSlicer Premade Config
Hi there,
So I got a Vcore3.1 with Volcano hotend, dual 5015s and using Mini Sherpa.
I have problem running at 8K with 100mm/s. There is not enough cooling.
...
Irregular offsets
Printer: v-core 3.1 500
BigTreeTech Octopus V1.1 Motherboard
BigTreeTech TMC2209 Driver SPI
Mosquito Magnum Hotend - Rat Rig Bundle
Bondtech LGX - Large Gears eXtruder...
asa warping 270x370mm
I'm trying to print a disk subpart on a v-core 3.1 4028 fan enclusore 2.0.
As long as the printing is going on addog there is nothing wrong however when you finish the print and slowly cool down the table and the part or the heater chamber. Such deformation will occur. What can I do that will reduce the bending of the part.
DEVIL ASA
Camber: 40
I can also heat the chamber if necessary....
is this the extruder doing?
It's the same whether wobbleX or RR oldham, so is this extruder or is it z motor tuning, or something else? Printed in ASA at .2 layer with .5 nozzle. Seems like a 2mm distance effect, or 10 layers.
weird artefacts everywhere+uneven layer stacking/uneven extrusion
Tell me if more information is needed
perfect first layer but bad subsequent layers
Been having this under extrusion issue where the first layer is laid slowly and well but subsequent ones suffer underextrusion.
First layer calibration not working properly?
I have been trying to fix my first layer, but have been having trouble dealing with what seems to be a non flat surface.
My bed mesh isn't great, but I would expect it to compensate better than this?...
small blobs everywhere
I just can't get rid of the small blobs, I've tried a number of settings, and that's the case with all filaments
Printer
V-Minion
Rapido HF 0.4 Nozzle ...
