ADXL burnt out?
At what point can I conclude my ADXL is dead? Is there a way to test? I have wired a harness to test the board using an extremely short Ethernet shielded cable and still get the (got ff vs e5) error.
I don’t think I have ever once been able to get an ADXL to work, how unreliable are these cheap boards? Should I just order a 3 pack and hope for the best?...
First belt test - vcore 3.1 300
Hi all.
Is there a person who can give me their 2 cents about this belt test? 🙂
The x gantry was a little off on one side so did the belt square thingy.
The only shaking sound I can hear is the big extruder wheel and plastic thing (with no filament) where the filament goes in (LGX lite)
Nozzle is a Revo Voron....
V-Core 3.1 enclosed 400 interpretation of graphs
i replaced the belt because my pulley was down and now with the new belts i can't get it tensioned correctly. Now my belts are tightend to the maximum and i get this graph.
How can i interpret that ?...
Help me fix my Resonance Issue VCore 3 500
i just upgraded my VCore 3 to 3.1 and assebled it all again with a ebb42 in place. Now the resonances on my y axis are giving me a headache. What can it be?
Spikes at high mghz belt tension
Any idea what this means ?
On lower frquencies my peaks seem to almost match, should i still try to tension the belts better ?
Thanks...
Serious issues with belt tension/IS after installing FMMM mod
Hi all,
As the title states I just got done installing the FMMM mod and am noticing a drastic decline in my belt tension graph and IS. What could be causing this?...
ringing after IS
im having some issues with ringing after IS. i have set the values to the recommended but still get ringing.
am i missing something?
nozzle 0.6...
v-minion y-axis woes
I have a conventional adxl on the x-axis and a kusba on the y-axis. below are my graphs. i am happy with x and dont know what to do with y. any help is great appreciated
Flat frequency response on one axis
Do we agree that I have a problem with my build ?
Vcore 3.1 with enclosure (but I haven't mounted the acrylic plates yet), 300mm....
EBB36 adxl axis swapping
I'm setting up a new toolboard and it is mounted on the back side of the tool head. Looking at the initial belt tension I think the axes need to be swapped. I added 'axes_map: x, z, y' to config, but it doesn't seem to change. Am I missing something?
Post Enclosure Kit Resonance
VCore 3.1 500. Just added the Enclosure kit, but not the panels yet.
At the same time, I replaced the printed motor cages, idlers, and joiners with metal plates.
Now my resonance is weird and I've been chasing it all day. The extra weird ones are the Y. I do not know what is going on there.
...
Second peak offset, first peak perfect
Hi,
Is anyone willing to let me know where to look at to solve that second peak not being aligned as the first one is?
Thanks!...
Something drastic on X
I've just run the input shaper for the first time in a little while, and I've got some drastic issue on the X axis that I'm not sure about. I've given everything on the toolhead a bit of a wiggle and it seems relatively stable - is there something obvious I'm missing? thanks!
shaper graphs not showing up in folder
any ideas why after I run shaper calibrate or any adxl345 commands with success the graphs are not in input shaper folde?
double peaks on x axes
just finished rebuilding my VC 500 into a VC 3.1 AWD and ive used spectroid to get the belts even and no matte what i try my belt tensions never match and no my x has this brutal double peak and ive tightened ever single screw there is and adjusted the belts over and over again but it wont go away
Something seriously wrong with my machine
After enclosing my VC3.1 300 and changing all parts to ABS - this is the best I can get after think ~100 attempts to tune/measure belts
Any ideas what is wrong and how to fix?...
Can't work out what this peak is
I have this peak when testing the belts. Nothing along the belt path is binding I just can't work out what it could be. Running ebb42. Switched to a completely different toolhead assembly and it's still present.
Belt tension graph is not behaving
I've tried everything, this is the best I can get..
Any help is appreciated...
