Vcore 500 mesh extreme cornering
range is almost 1mm. not sure what is wrong or what to do about it. i got a new 500mm plate but the issue persisted. I don't know if replacing the magnetic sticker pad underneath will do anything. i'm trying sliding sheets of paper in
Vcore 500 bed mesh
I need some help in order to understand what part of my printer is out of whack. I have tried adjusting as much as i could but obviously its not working. Please help thank you.
Bed Mesh V-Core 500 tilted (Front right low, back left High 0.77 difference)
Hey,
I am trying to ccorrect my bed mesh on the 500 i have. When doing a z tilt and then the mesh the front right corner is too low and prints dont adhere. Shouldn't the z tilt solve that for me? Am I missing something else? I've added a picture to show my mesh....
Solution:
oh, it is creeping? double and triple-check your couplers from the z motor shafts to the lifting screws, make sure the set screws are tight
my mesh is bad...
Hello. https://www.youtube.com/watch?v=h7ZTq2dDTkM I tried to fix my printer according to the video here. Then, after meshing, the graph appeared like this. What do you think is the problem?
First Layer Problem with Adaptive_Mesh
Hello. When I use adaptive mesh, I have problems with the first layer. But don't use it, I don't have any problems when I use normal bed_mesh. Something caught my attention, I think maybe this is the reason. As you can see in the screenshot, no matter which part I print, "PROBE_FOR_PRIMING: Probing the prime location at X: 493.0 Y: 33.0" always takes measurements from this point before meshing. Why does it always measure from X: 493.0 Y: 33.0?
Görsel...
Help Please
I installed the titanium tube on my V-Core 3.1 400 and I am little perplexed with my mesh now. It was relatively flat prior to install accross x and now I have this bow. I have loosened and tightened all screws on the x rail a couple of times in order to 1.5 NM. Any thoughts? It's also a little strange that the bow is less at the front.
VC3.1 Enclosed 400
So afaik i have to move the extrusion up at the fron but that didnt rly help so im posting it here.Yes i have watched the video for squaring the vc3.Side note i bought the toro tube and apparently bimetal effect is going crazy as now i dont print abs only petg so i have only the side panels on
Bed Mesh taco with some obvious inflection from alignment
Rebuilding a used Rat Rig 300 that the prior owner never quite got to work right. And I'm new to Rat Rigs, which isn't making this easier. These graphs were taken at room temp because I'd like to get a baseline in before I start introducing heat to the alignment.
Looking at the range of 0,0 to 300,0, with the little twists up and down at the end, and then the plate in the 300,300 tilting down, it's obviously I have some squaring to fix. But frankly, it seems like the things I'm trying are not really doing much. Like, I get the discrete feeling the rear Z axis isn't fully aligned, and that's what causing the twist, but I'd like to see if anyone else has any better ideas, as I think there's telltale signs that more knowledgeable people might be able to spot....
Solution:
Is perhaps best fixed with a line of KAPTOn tape
VC3.1 Enclosed 400 Back Corner Peak
Working through commissioning my VC3.1. I'm seeing a peak in the back left corner. Not sure if this range is perfectly okay, or if it's something I should work to bring down. I want to get good results, but not looking to potentially make 'good enough' worse.
Mesh not compensating in back of print volume VCORE3 300
I've recently been trying to maximize the use of my build volume, however I've been running into an issue where the entire rear section of my bed (y 150-300). is lower than the front.
My heightmap seems pretty solid with a deviation of around 0.199. I'm using a Euclid probe and the repeatability is perfectly fine, offsets are set, z offset is set etc...
I've been trying to find any way to correct this but from everything I see it just seems like the mesh compensation isn't working properly. ...
