Has anyone experienced weird effects with the AV8B? I'm experiencing very high stick forces that fe

Has anyone experienced weird effects with the AV8B? I'm experiencing very high stick forces that feel like a very offset trim, but doesn't move with trim inputs.

MMerlins51 Has anyone experienced weird effects with the AV8B? I'm experiencing very high ...

Jehly•8/2/23, 1:11 AM

I experienced this exact issue with the A10CII. Make sure you fire up the Rhino with the stick near the center. Fixed it.

JJehly I experienced this exact issue with the A10CII. Make sure you fire up the Rhino...

Merlins51OP•8/2/23, 1:11 AM

Thanks! Will try that.

Jehly•8/2/23, 1:11 AM

Yeah, when you turn it on just do what you can to keep it roughly in the center position. You'll hear the "happy beeps" and it should sit centered

Jehly•8/2/23, 1:12 AM

I also ensured my calibration was correct, just to be sure.

Skete•8/2/23, 3:24 AM

hey guys, does anyone know if i can turn the main mount where the rhino connects to the joystick to induce a 15 degree offset, I know with extensions they normally come with it but with myset up i can only run the short throw.

blave549•8/2/23, 2:22 PM

I see a couple mentions of endstop improvements in the Configurator app release notes. Does this mean that I might not need to 3DP a limit stop plate? If it matters, in general I am not a "yank and bank" flyer and right now am only using MSFS, so no combat at all.

Bblave549 I see a couple mentions of endstop improvements in the Configurator app release ...

PiNKSH!T•8/3/23, 7:43 AM

the software endstops got a huge improvement a few updates ago & they act really good now, the software endstops are obviously great if you want to be able to change them for different aircraft, tho cause I've been flying dcs more than msfs I did get a physical endstop which is good for combat flying.

Phantom•8/3/23, 1:18 PM

@walmis The new adapter arrived, installed, worked first time zero issues mate, thank you so much, appreciated

blave549•8/3/23, 10:36 PM

First day user question (btw the Rhino is AWESOME -- getting a hand-built gizmo like this, with its quality of build, highly functional Configurator app, web-based firmware updates... wow, such a great value):

When I'm not flying, should I Push The Big Red Button or just turn down the spring gain? Is there any point in doing either, in terms of prolonging the life of the Rhino, its motors, and such? (BTW when I push the button the Configurator app stops seeing the axis inputs, even though Windows can still see them, and I have to restart the app)

Jehly•8/3/23, 10:58 PM

I don't know if it's the right thing to do, but I hit teh red button.

ddrake1984•8/3/23, 11:17 PM

I hit the red button when not in use

Reed•8/4/23, 1:29 AM

Same

AndyHill•8/4/23, 2:06 AM

the axis inputs go away with the big red button, because it shuts off all electric power to the motors and the axis sensors are an integral part of the motors

Wwalmis Gotcha, I'll add entries to configure each hat separately in the next version.

TheZoq2•8/4/23, 9:18 AM

Did you end up releasing this feature yet?

blave549•8/4/23, 6:24 PM

I just found out the hard way that the button/hat mapping for the Thrustmaster Warthog grip mounted on the Rhino is different than that shown in the TMW manual (and which is what both the TM and Virpil bases report). I'm asssuming this is intentional for some reason, but I have to say it's not optimal

blave549•8/4/23, 10:31 PM

OK today is Mess Around With DCS Day. I am currently flying the UH-1, and I'm not sure how I should have things set up in both Configurator and DCS. Using TelemFFB I'm getting some wonderful effects (e.g. ETL vibrations, which I can feel in my seat!), but the force trim stuff doesn't seem to do anything. I've turned on everything I know to turn on in DCS...

Bblave549 I just found out the hard way that the button/hat mapping for the Thrustmaster W...

kingjamez•8/4/23, 10:36 PM

You can easily map any button to any button in the VPForce configurator. Most of us who use the TMWH have the buttons as they are reported to the VPForce board mapped to the buttons that the original design mapped them to. It takes about 5 minutes to remap.

kingjamez•8/4/23, 10:37 PM

Kkingjamez You can easily map any button to any button in the VPForce configurator. Most of...

blave549•8/4/23, 10:38 PM

Oh golly I wish I'd known that. I wondered what the function was for! Doh!

Bblave549 OK today is Mess Around With DCS Day. I am currently flying the UH-1, and I'm no...

Firaga•8/5/23, 3:36 AM

Remember to flick the force trim ingame switch from the cockpit. It works for UH-1 and makes a huge difference.

Bblave549 OK today is Mess Around With DCS Day. I am currently flying the UH-1, and I'm no...

sydost•8/5/23, 9:07 AM

Usually when this happens people have selected sticky option on for spring effect in VPForce configurator. Check that it is off. That overrides the spring force commands from DCS. Another usual suspect is to select wrong trimmer mode in DCS for UH-1. Select “default” trimmer mode (not the one which mentions FFB). If it wasn’t one of these it would be a good idea to post screenshots of VPForce configurator’s settings and effects tabs for troubleshooting.

Boeing757sim•8/5/23, 9:39 AM

Suggestions on which one to order plz

TTheZoq2 Did you end up releasing this feature yet?

Skete•8/5/23, 9:43 AM

Nah it's not out yet

BBoeing757sim Suggestions on which one to order plz 😅

Jehly•8/5/23, 11:06 AM

What are you powering? I just ordered something like the first one and it’s powering the stick AND pedals. So, the second if you’re just powering one.

Boeing757sim•8/5/23, 11:10 AM

@jehlybean - 02 Nos of 57BLF03, using it for ROLL and PITCH, for a DIY yoke

BBoeing757sim @jehlybean - 02 Nos of 57BLF03, using it for ROLL and PITCH, for a DIY yoke

Jehly•8/5/23, 11:26 AM

Well, I'm just reading the #

faq and doing some very light googling. The motors you ordered appear to be the same ones that came in the base (per the notes in the #

faq). The stock power brick shipped with the bases is 180W. I've personally asked a similar question in here when I ordered stuff for my pedals (I want a single power supply, not two) and I bought a 350W. For you, I humbly believe a 240W would be fine.

Boeing757sim•8/5/23, 11:30 AM

@jehlybean thanks , shall start the search for the PSU.

Jehly•8/5/23, 11:31 AM

I got mine from amazon for "like new" for about 15% off.

Jehly•8/5/23, 11:32 AM

Not terribly expensive. I personally believe the "laptop power bricks" are a bit overpriced.

Boeing757sim•8/5/23, 12:48 PM

Yep I will also stick to the SMPS type PSU’s

Boeing757sim•8/5/23, 12:50 PM

@jehlybean what pedals are you using ?

BBoeing757sim @jehlybean what pedals are you using ?

Jehly•8/5/23, 12:52 PM

Virpil. I haven’t done it yet, but I’m intending to turn them into FFB.

Jehly•8/5/23, 12:53 PM

Love them and I think this will only make it that much better.

Boeing757sim•8/5/23, 1:09 PM

Nice, right am I am in the initial stages of designing a diy Boeing yoke, next will be the pedals for FFB

FFiraga Remember to flick the force trim ingame switch from the cockpit. It works for UH...

blave549•8/5/23, 2:00 PM

I thought I had that on but will try again. Thx!

Ssydost Usually when this happens people have selected sticky option on for spring effec...

blave549•8/5/23, 2:01 PM

I have Stickly disabled, and I'm trying the Default setting in DCS. Maybe the switch thing that the other gentleman mentioned is my issue.

Bblave549 I thought I had that on but will try again. Thx!

Number481•8/5/23, 2:01 PM

If you've been flying helis in MSFS... you may need to disable sticky (Haha.. nvm)

Bblave549 I have Stickly disabled, and I'm trying the Default setting in DCS. Maybe the sw...

Number481•8/5/23, 2:04 PM

https://docs.google.com/document/d/1YL5DLkiTxlaNx_zKHEYSs25PjmGtQ6_WZDk58_SGt8Y/edit#heading=h.uc6h2nwcqoka the doc should have what you need to get it working in DCS (and specifically with the Huey)

TheZoq2•8/5/23, 2:42 PM

Is FFB still broken on the gazelle? or is there a combination of settings that makes it work

TTheZoq2 Is FFB still broken on the gazelle? or is there a combination of settings that m...

blave549•8/5/23, 2:54 PM

I spent my first Rhino/DCS time in the Gazelle, after not touching DCS for over two years. It is unflyable and I can't figure out why. The collective behaves very strangely, unlike that in the UH-1. I loved the Gazelle even with the old, widely cursed flight model, but something ain't right somewhere.

TTheZoq2 Is FFB still broken on the gazelle? or is there a combination of settings that m...

Anthony•8/5/23, 3:18 PM

Make sure to put the curve/gain in Gaz special settings to zero

TheZoq2•8/5/23, 6:05 PM

I think I had that set. Selecting None for the trimmer mode makes the rhino go back to the center on trim release. Selecting Instant, it drags it off to the side the more I release the trim button

Kruger•8/5/23, 10:42 PM

You need to go to Special tap, there is (I think No 5) a extra option for FFB for this Modul. make sure it is ticked

Kruger•8/5/23, 10:43 PM

The Gazelle flies perfecly fine for me, just did 4 hours in Multicrew in it

TheZoq2•8/6/23, 9:51 AM

Do you mean the "Module individual force feedback toggle"?

TheZoq2•8/6/23, 10:00 AM

That and Instant trim seems to have done the trick, thanks!

HPLsCat•8/6/23, 12:31 PM

Is there a way to get Virpil analog sticks/thumb wheels working when connected to the Rhino? Specifically the VFX, but looking at the FAQ it's not supported yet. Was hoping to get the analog DLC working, but guess that's later.

HHPLsCat Is there a way to get Virpil analog sticks/thumb wheels working when connected t...

walmis•8/6/23, 12:35 PM

It's implemented already

HPLsCat•8/6/23, 12:36 PM

Thanks walmis

Spanner•8/7/23, 11:29 PM

@walmis new adapter worked flawlessly. thank you!

Has anyone experienced weird effects with the AV8B? I'm experiencing very high stick forces that fe

Similar Threads