Is there a variable in TelemFFB to reduce engine rumble in fixed wing aircraft? I only see a switch
Is there a variable in TelemFFB to reduce engine rumble in fixed wing aircraft? I only see a switch to turn it on and off in the stock config file.
NShould work for DCS or MSFS (or IL2).. even if its maybe not in the default sim section
SSo....crazy thing I have seen sine the last DCS update....
Tomcat on deck before launch, wipe out the controls
Pull back on stick at a moderate to high rate....boom!....pitch motor takes a nap and base needs a power cycle to wake up
Odd since the only ffb forces are the basic spring and damper rates.
In flight, a rapid split S, not really slamming the stick aft...smae effect...nap time for pitch. Never an issue in roll.
Outside of DCS...I can whip the stick around and never an issue.
Tomcat on deck before launch, wipe out the controls
Pull back on stick at a moderate to high rate....boom!....pitch motor takes a nap and base needs a power cycle to wake up
Odd since the only ffb forces are the basic spring and damper rates.
In flight, a rapid split S, not really slamming the stick aft...smae effect...nap time for pitch. Never an issue in roll.
Outside of DCS...I can whip the stick around and never an issue.
S
SDoes not seem like a current spike.....but maybe it is happening too fast to see in the software?
Thanks for consideration in advance...
Thanks for consideration in advance...
AJust sent in an order for the 2x motor kits+usb for a diy setup - are their any other electronics I will need to get that are not included?
SPSU, 5pin DIN connector for grip, fan, jst connectors...
https://github.com/protomaker964/Rhino-FFB-Clone-3D_Printed/tree/main
https://github.com/protomaker964/Rhino-FFB-Clone-3D_Printed/tree/main
GitHub
3D print files, parts list and instructions to build a DIY version of the Rhino FFB Stick base using the VPForce motor kit - GitHub - protomaker964/Rhino-FFB-Clone-3D_Printed: 3D print files, parts...
Sparts list in the build pdf
WDo you have telem running? Can you check the fault code once it enters the failed state?
AThank you! I’m actually looking to use this print! I posted a question about the pullys in the DIY channel I figure it would be a better channel than a support channel for the actual rhino
SDang, forgot about telem, I will give that a look today. Thanks!
BJust a note that I ran into something that I'd never seen before in DCS Open Beta (that is almost certainly unrelated to anything Rhino). In the A-10C II, my stick would not work, even though the x/y axes showed up as working in the Control Options dialog. At one point it started working, but then stopped again. I think, but am not sure, that it's specific to the Hawg. I tried a couple other aircraft and they were fine.
SGood morning (afternoon for you I think),
SO I ran Telem and did some testing.
When I can induce the shutdown, nothing shows in telemetry.
So I messed around with the max gain pot and lowered it some and no pitch shutdown on faster pulls.
Certainly seems related to effect intensity and just the pitch motor shutting down.
Do you think this is maybe power supply related? I was thinking not since the roll motor stays active.
Could this be a motor current issue and will the max current setting in the software help? Though it is set to 25A and the PSU is not gonna push that much.
Keeping max gain turn down a bit seems to keep it all in check, but I would love to get back to the strength settings I had if possible.
Thanks!
SO I ran Telem and did some testing.
When I can induce the shutdown, nothing shows in telemetry.
So I messed around with the max gain pot and lowered it some and no pitch shutdown on faster pulls.
Certainly seems related to effect intensity and just the pitch motor shutting down.
Do you think this is maybe power supply related? I was thinking not since the roll motor stays active.
Could this be a motor current issue and will the max current setting in the software help? Though it is set to 25A and the PSU is not gonna push that much.
Keeping max gain turn down a bit seems to keep it all in check, but I would love to get back to the strength settings I had if possible.
Thanks!
WA motor fault code would be useful here, it's displayed in the status bar (OK when operational)
Sahh in the status bar ok...since in the main telem screen I saw nothing but the normal connections ok, effects on, and the power reset.
In this status bar?
In this status bar?
S
WNo, at the bottom:
WIt will show a fault code if the motor shuts down with a long beep
SGot it thanks
TIf I set the pot function as Spring Gain, does it mean that at 100% pot value the spring effect would be at 30% according to the settings below?
Syep the knob goes to that max setting
Shello, why in msfs flying th a2a comanche, I'm seeing the yoke moving but that is not reproduced in the rhino?
Swhat kind of movement are you seeing? is this with or without autopilot
NYou gotta give us more info.. Are you using TelemFFB? Are you using the latest version which adds trim/AP following support? Have you set up the trim/ap following per the TelemFFB section in the VPforce manual?
Syes yes and yes
SI have it this way:
S#############################
##### MSFS Specific Defaults
#############################
telemffb_controls_axes = True
trim_following = True
ap_following = True
##### MSFS Specific Defaults
#############################
telemffb_controls_axes = True
trim_following = True
ap_following = True
Sin the config.ini
NAnother quite important question... Do you have 'sticky spring' enabled in VPf Configurator?
Slet me check
Sno
S
S
Syes I did
SI felt like it was for nothing, but I did. or felt like I did it someway wrong
Sjust cleared the bind and assign it back again as it was..
Nwhat does your comanche settings look like in your telemffb config?
Nlast thing would be to drop a copy of your TelemFFB log file in here for me to look at.
SI think I have nothing specific for it
Sconfig.ini24.32KB
Sif you have some specific for the comanche that would be awesome
Sand thanks!!
NThis looks like maybe an old copy of the default config.ini? The default for the latest TelemFFB has the a2a pa-24 (comanche) in it already
NWithout a specific aircraft section telling TelemFFB that the aircraft is a "PropellerAircraft".. things won't work right.
Sok.. all update and check if it has the comanche config part
Nyour telemFFB log would tell me alot too
Sso, I need to unbind it a leave it unbind right?
Nyeah.. in order to get around the way MSFS behaves.... TelemFFB has to be the source of the axis position for the trim following feature to work.
Sso I think I did all things right, and I have all set to true and unbinded the axis and im getting them to move in the sim
Sbut I put power to the ap and watch the yoke move in the sim but I dont see it in the rhino