D
Psomething else comes to mind for me when I think of a screw 
DHey there, I am considering getting the HPG H160 for MSFS, I was wondering if that in conjunction with your TelemFFB software, would work with a MS Sidewinder FFB2? Thanks in advance for any info
WHi, in the current state it will not work with other devices other than the Rhino, but in theory it's possible to port the hardware layer of telemFFB to other hardware.
DGotcha, thank you for the info!
JNot sure if anyone else has experienced this, but over the last FFB update or two I noticed it flips my rudder input and there's no way for me to re-bind or invert it from inside DCS. If I close TelemFFB, works normal.
JHave you experienced this, @Number481?
NTalking fixed wing? Very high probability there are bugs in the rudder trim following feature that I haven't found yet.
Ntry
pedal_trimming_enabled = false... I had no problems with it in any of the module testing I did.. but I certainly did not test all modules and didn't actually fly around muchJI'm flying specifically A10CII
JIs that in the pedals.ini file
NIt’s in the default config but you can add it in your userconfig
MIs there any way to add support for the new F-15E setting that gives full deflection at half forward stick (a la the real jet). Like add a soft/hard stop to the rhino when it detects you're in an F-15E and that option is checked
NNot to detect the setting in DCS, but you could create a configurator profile for the 15 and load it dynamically when in the f15 via TelemFFB. Would be up to you to ensure the setting is enabled in the sim.
JConfirmed. This was the issue.
JSet to false and no inverted pedals.
NHmm. I’ll take a look. The a10 was one I did test but…
MPretend like I'm a dumb dumb, is there a guide to actually setting this up?
Mty, is there a guide to setting up a stop on the axis for the profile?
Nnot that I know of.. it is just a matter of configuring the endstop feature in configurator, but I don't use it so I can't really give you any tips.
MThe profile load feature isn't working for me. I created a new profile, saved it to the configs folder, and pointed the telemffb config at it via what you posted, it doesn't update in the F-15
NI know the feature works, so...
- check the telemffb log for any clues
- post the relevant section if your telemffb user config
M2023-11-16 21:52:32.906 - WARNING - Unknown parameter vpconf
MThat's gotta be the issue
M[F-15ESE]
type=JetAircraft
vpconf='C:\Users\Mike\Desktop\VPforce_FFB_Configurator_v1.0.16-1\configs\F-15E.vpconf'
runway_rumble_intensity=2.0
speedbrake_buffet_intensity = 0.15
gear_buffet_intensity = 0.15
type=JetAircraft
vpconf='C:\Users\Mike\Desktop\VPforce_FFB_Configurator_v1.0.16-1\configs\F-15E.vpconf'
runway_rumble_intensity=2.0
speedbrake_buffet_intensity = 0.15
gear_buffet_intensity = 0.15
Nits probably barfing on the backslashes... try the relative path using forward slashes
'./configs/F-15E.vpconf'M2023-11-16 22:02:35.630 - WARNING - Unknown parameter vpconf
Same thing with different slashes
Same thing with different slashes
Nlooks like there's a bug that displays that (Because there is no internal default value in TelemFFB).. but it should still load the profile
NYour rhino will beep when it loads (unless you have the buzzer disabled in configurator?)
MNo beep, no profile swap
NSend the whole TelemFFB log. I’ve got a couple minutes before I have to log off.
MNdamnit... (my bad).. delete this from your config (both default and user if it exists in there).. this is conflicting with the ESE...
NI'll need to push an update to fix that permanently
Mtrying without that
Mstill didn't work
Nhmm.. not sure what to say... after deleting the erroneous part of the config per above, it works fine for me.
Nlook at your log again and make sure it is not still overwriting the read config from another section.. this is what your previous log said
The bad [F-15E] section was overwriting what you had in the [F-15ESE] section
The bad [F-15E] section was overwriting what you had in the [F-15ESE] section
MI'll check the most recent log
Nthat looks normal... its finding your configurator install and its picking up on the vpconf setting... cant say why its not working....
What happens if you do this from a windows command prompt?
What happens if you do this from a windows command prompt?
"C:\Users\Mike\Desktop\VPforce_FFB_Configurator_v1.0.16-1\VPforce_FFB_Configurator.exe" -config "C:\Users\Mike\Desktop\VPforce_FFB_Configurator_v1.0.16-1\configs\F-15E.vpconf"MThe first one opened VPForce Configurator
MThe 2nd one threw a windows "how do you want to open this"
Nyou need to run it all as one command
MThat does nothing, doesn't throw an error
MDoesn't even reopen configurator when I do them both together
Nits not supposed to.. thats how you programaticaly load the profiles. That is exactly what TelemFFB does.. so it looks like the problem is not with TelemFFB
Ntry this too, and make sure it returns the right path to your configurator install..
reg query "HKEY_CURRENT_USER\SOFTWARE\VPforce\RhinoFFB" /sMexportPath REG_SZ C:/Users/Mike/Desktop/VPforce_FFB_Configurator_v1.0.16-1/configs