more info needed.... does it crash? does it say it did something but nothing happened? does it do
more info needed.... does it crash? does it say it did something but nothing happened? does it do nothing at all?
Nrecommend trying not launching from a shortcut. launch directly from the exe.. but if the in-pace install is already corrupted, it might be easier just to grab the latest zip distribution and start fresh https://vpforcecontrols.com/downloads/TelemFFB/?C=M;O=D
Mmh, it crashes and the .xml config has nothing in it.
Mif I say "no" to the initial config.user.ini conversion prompt it behaves normally.
MI mean, it starts, but if I try the conversion from Utility it crashes silently before doing anything
Ninteresting... send me your userconfig if you don't mind... I'd like to investigate why its failing. If the config worked with the previous TelemFFB without error, it should convert over.
Msure, DM?
Nthat works
TTelemFFB (3017d8df) shows errors for HPG160 and MSFS
But telemffb_controls_axes is enabled and cyclic axes are not bind.
How can I solve this?
But telemffb_controls_axes is enabled and cyclic axes are not bind.
How can I solve this?
Ttelemffb_controls_axes = enable in the 2 locations.
TNot working 
Nresolve the issue in the log message....
and
I'll look to see if there's an issue with the default settings because the axis control should be enabled by default for those helicopters
and
I'll look to see if there's an issue with the default settings because the axis control should be enabled by default for those helicopters
T
Axis control checked now! And button configured!Thanks!
FI've been having a play with the latest version of Telem FFB and enjoying all the work put into the new UI. I did notice when I got in the spitfire in DCS that there was no elevator droop when not moving and I couldn't find any section to adjust that value. Am I just been stupid by not seeing it or was it missed in the initial rollout?
FAlso can't find settings such as ground touch down.
Nlooks like elevator droop was, in fact, missed... but the touchdown effect should be part of 'runway rumble'
FI just tried changing runway rumble from 100% to 0% using the Gazelle and noticed no change when doing a heavy landing. Just to be sure I went to another module in between just to make sure the setting changes were loaded.
Nyou sure? whats your constant force slider set to in vpf configurator?
FConstant force slider set to 100% in vpf config
Nok... you should be able to feel something (albiet potentially small) when doing a (rough) landing.. but you are onto something as the max range in the default config is not big enough.. thats a weird setting that sometimes needs to be >1.0 to be felt and the current defaults are limiting it to 0.4 or less.. next update will allow the setting to go up to 4.0 (will still be a slider of %0-100) which will have the ability to really jolt you during a rough landing 
F'awaits the future broken wrist 
Thanks for all the awesome work!
Thanks for all the awesome work!
TI understand that motor Y usually is hotter, but mine has a difference of 10c, is that ok?
Tthere
WYeah, don't worry about the temps
3When i try to run Telem It's blocked by my malware protector because it detects Neshta.Virus.FileInfector.DDS.
3Is this safe? Should I allow this file?
SHello, anyone would be so kind to tell me the exact measurements of the screw thread of the stick and base? Are they imperial or euro?
3I get the fallowing error when launching
Telem
Telem
3I was using it succefully earlier but tried to copy one plames setting to another then this erroe.
Nwhen you say copy, you mean cloning a new aircraft through the 'create new aircraft' dialog?
3Yes, Ithink so
Ncan you drop a copy of the user config in here? located in
Then after dropping it here, try to delete file and rename the
Users\<your username>\AppData\Local\VPForce-TelemFFB\userconfig.xmlThen after dropping it here, try to delete file and rename the
userconfig.xml.backupuserconfig.xmlmessage.txt7.47KB
3message.txt7.47KB
Nmaybe try to zip it up first.. not sure if discord is mangling the text when trying to paste the xml file or what
3message.zip1.11KB
3That didn't work
3Still won't start
Nthe zip still contains a file called message.txt that has the same content as the two above posts.
If the backup is also corrupted, best to just delete the userconfig.xml and start TelemFFB. It will create a new one. If it fails again when you clone, try to zip up the actual xml file and send it
If the backup is also corrupted, best to just delete the userconfig.xml and start TelemFFB. It will create a new one. If it fails again when you clone, try to zip up the actual xml file and send it
3Thanks for your help!!
message.txt22.16KB
3Is this what your looking for?
3Great! got it started
Nyes. Is that the one that was failing ?
3Yes
TGood evening!
I had a question regarding order#587. I was invoiced and paid the order, and the order status changed to "paid." Then I was invoiced again, but this time for a lower amount? The charge shows on my credit card statement.
I had a question regarding order#587. I was invoiced and paid the order, and the order status changed to "paid." Then I was invoiced again, but this time for a lower amount? The charge shows on my credit card statement.
WYou can disregard that, clerical error. Will ship it today.
Sanyone who had problems with avira moving telemffb to quarantine?
DHi @walmis ...I have a question for you - I recently bought the new v2 Realsimulator FA-18 stick handle to use with my RS FSSB side stick. I'd really like to use it with the Rhino as well, and for the most part it works with the 64-button Generic Grip profile in the VPforce configurator, except for a few buttons which won't register or map in the button mapping section. They show as buttons 62 & 63 in the Realsimulator config tool, but no dice on VPForce. Is there something I can do to help troubleshoot this to figure it out?
DThis is the handle I bought (F18CGRH v2):