Any luck? I will be trying the same in a few months.
Any luck? I will be trying the same in a few months.
BNo luck yet. Useable since I’ve been assigning buttons via the BLE portion of the grip, but still nothing registering on the Rhino itself with that particular grip
WI know a few RS users that successfully use their grips, so this instance is kinda strange. Since the grip receives power and BLE works fine, I assume the connection is good with the grip.
DNeeds washer, you don’t want to over tighten
PA plywood sheet 10-15mm (depth) that's big enough for your seat to sit on with the Rhino mounted in front, you can even have it big enough to go under your desk & have rudder pedals sit on top too. Just measure where the Rhino will go drill the 4 holes & put some small bolts in from what will be the bottom & then once in place you can bolt the Rhino in place on the "floor" right in front of your chair.
LThanks for the suggestion, I just finished a quick and dirty version (Just drilled 4 screws into a piece of plywood and placed in front of the seat) works perfectly fine.
Pnice works well
R@walmis
FFB Configurator
Spring Gain Map Graph Appears to be Reversed
When adjusting the spring map, the graph adjusts the gain in the opposite sense to the axis movement displayed. In the attached image the position of each axis as indicated should result in the mapped spring gain. However, the gain is as mapped for the opposite direction. In this example, the gain is zero for the indicated postions but follows the map when moved in the opposite direction.
My Rhino Y-axis is inverted (e-stop facing forward). X-axis is not inverted but the direction of movement displays in the map graph and in the display on the settings tab as expected.
FFB Configurator
Spring Gain Map Graph Appears to be Reversed
When adjusting the spring map, the graph adjusts the gain in the opposite sense to the axis movement displayed. In the attached image the position of each axis as indicated should result in the mapped spring gain. However, the gain is as mapped for the opposite direction. In this example, the gain is zero for the indicated postions but follows the map when moved in the opposite direction.
My Rhino Y-axis is inverted (e-stop facing forward). X-axis is not inverted but the direction of movement displays in the map graph and in the display on the settings tab as expected.
ISame ting to me. I have just mounted a Winwing F18 stick with the winwing adapter and is not recognizing the trim switches. Have you managed to make it work? Anybody else has the same issue?
WDid you change the profile to WinWing adapter?
WThanks, I will make sure to correct this in the new version
IDone, now is recognized. Thanks
I3
Anew version you say? :blobsmirk:
BHi , any suggestions on how to update the firmware, getting this error @walmis
BWindows 11, tried with Edge, chrome no luck
BI did try that once, will try again tomorrow after a re-boot
B@walmis It’s updated, thanks a lot
THi! I'm encountering a strange behavior on my Rhino, occurs with both aircraft I tried this morning (DCS Tomcat and Hornet). It's almost like effects from TelemFFB are full force, but I get no resistance (compared to yesterday) when pushing/pulling the stick. Would this ring a bell? I did not remember modifying the settings since yesterday, tried unplugging both USB and power brick. Pot is 100% and set to Master Gain.
WCan you show you configurator settings? Did you run telemFFB during these tests ? Is the spring ok when out of the sim ?
TSpring is typically OK only in the sim, not really a spring effect out of the sim
WIt's not connected
TSorry
TJust realized that after posting
T
T
WTry importing the default Rhino configuration in
configs/Rhino-defaults.vpconfTWorks like out of the box, didn't realize that the defaults file was there, thanks!
TActually just turned on TelemFFB, and without it, spring effect, with it no spring effect
NAre you loading any vpconf profile via TelemFFB? It doesn’t do anything to affect the spring forces on the joystick axis in DCS.
TOK, just found it on the TelemFFB KB, it is this issue : https://discord.com/channels/965234441511383080/1093558100713279508/1203549616189214784
TNo joy with vJoy, disabled it and it works!
AThe WinWing adapter, can that be used on Virpil’s extensions?
I’m considering a WW stick, but with my current setup I can’t really do without the VPC Z extension, hence the question.
I’m considering a WW stick, but with my current setup I can’t really do without the VPC Z extension, hence the question.
ASo it’d be:
WW grip
+
WW adapter
+
VPC Z extension
+
Rhino
(Best way I can describe it without a poor attempt at using MS Paint)
WW grip
+
WW adapter
+
VPC Z extension
+
Rhino
(Best way I can describe it without a poor attempt at using MS Paint)
Aany chance you got simapp pro working with your rhino? im using the f16ex grip and trying to get it to work as well thanks!
FHi, I'm building a grip. I would like to know the diagram of the mini dim 5 pin connector of the VP Force base to connect it to the controller inside the grip. Thank you very much.
MIs it possible to make VP config & VP telem load an individual profile automatically for different modules?
WHere's the pinout for the TM/Virpil/VPforce interface
FThank you very much
MNice, did not realise we have a spiffy new manual! will get reading!
MMay have a muddle going on.....seem to have 2 folders called VPforce-TelemFFB-wip-dbdbb26f. They have different contents and dates, see screenshots
MOne, which is the newest does not have any config.user file....?
MWhich one do I need?
MMay I also ask ( been reading the manual...) in what circumstances would you use the endstops function & axis rescale and why? The manual expalins what they do, but not why and how you might use them. thanks
WAxis scaling : for example to stiffen controls, to mimic F-16 force sensing somewhat.
Endstops: to (soft) limit travel, the same purpose as the hardware throw limiter, but less reliable.
Endstops: to (soft) limit travel, the same purpose as the hardware throw limiter, but less reliable.
SHey all - sorry if this is a daft question. I'm nearly at the point where I need to buy a DIY kit and was wondering what the difference between all the options are. Any advice on which I should purchase?
Nthe one in your downloads folder is the new file structure
MGreat, I already have the throw reducer fitted, so basically, I dont need to worry about using either of those 2 options? thanks
MThanks 481, do I need to copy over my user ini file to the downloads location? then delete the other?