Thanks, I will make sure to correct this in the new version
Thanks, I will make sure to correct this in the new version
IDone, now is recognized. Thanks
I3
Anew version you say? :blobsmirk:
BHi , any suggestions on how to update the firmware, getting this error @walmis
BWindows 11, tried with Edge, chrome no luck
BI did try that once, will try again tomorrow after a re-boot
B@walmis It’s updated, thanks a lot
THi! I'm encountering a strange behavior on my Rhino, occurs with both aircraft I tried this morning (DCS Tomcat and Hornet). It's almost like effects from TelemFFB are full force, but I get no resistance (compared to yesterday) when pushing/pulling the stick. Would this ring a bell? I did not remember modifying the settings since yesterday, tried unplugging both USB and power brick. Pot is 100% and set to Master Gain.
WCan you show you configurator settings? Did you run telemFFB during these tests ? Is the spring ok when out of the sim ?
TSpring is typically OK only in the sim, not really a spring effect out of the sim
WIt's not connected
TSorry
TJust realized that after posting
T
T
WTry importing the default Rhino configuration in
configs/Rhino-defaults.vpconfWorks like out of the box, didn't realize that the defaults file was there, thanks!
TActually just turned on TelemFFB, and without it, spring effect, with it no spring effect
NAre you loading any vpconf profile via TelemFFB? It doesn’t do anything to affect the spring forces on the joystick axis in DCS.
TOK, just found it on the TelemFFB KB, it is this issue : https://discord.com/channels/965234441511383080/1093558100713279508/1203549616189214784
TNo joy with vJoy, disabled it and it works!
AThe WinWing adapter, can that be used on Virpil’s extensions?
I’m considering a WW stick, but with my current setup I can’t really do without the VPC Z extension, hence the question.
I’m considering a WW stick, but with my current setup I can’t really do without the VPC Z extension, hence the question.
ASo it’d be:
WW grip
+
WW adapter
+
VPC Z extension
+
Rhino
(Best way I can describe it without a poor attempt at using MS Paint)
WW grip
+
WW adapter
+
VPC Z extension
+
Rhino
(Best way I can describe it without a poor attempt at using MS Paint)
Aany chance you got simapp pro working with your rhino? im using the f16ex grip and trying to get it to work as well thanks!
FHi, I'm building a grip. I would like to know the diagram of the mini dim 5 pin connector of the VP Force base to connect it to the controller inside the grip. Thank you very much.
MIs it possible to make VP config & VP telem load an individual profile automatically for different modules?
WHere's the pinout for the TM/Virpil/VPforce interface
FThank you very much
MNice, did not realise we have a spiffy new manual! will get reading!
MMay have a muddle going on.....seem to have 2 folders called VPforce-TelemFFB-wip-dbdbb26f. They have different contents and dates, see screenshots
MOne, which is the newest does not have any config.user file....?
MWhich one do I need?
MMay I also ask ( been reading the manual...) in what circumstances would you use the endstops function & axis rescale and why? The manual expalins what they do, but not why and how you might use them. thanks
WAxis scaling : for example to stiffen controls, to mimic F-16 force sensing somewhat.
Endstops: to (soft) limit travel, the same purpose as the hardware throw limiter, but less reliable.
Endstops: to (soft) limit travel, the same purpose as the hardware throw limiter, but less reliable.
SHey all - sorry if this is a daft question. I'm nearly at the point where I need to buy a DIY kit and was wondering what the difference between all the options are. Any advice on which I should purchase?
Nthe one in your downloads folder is the new file structure
MGreat, I already have the throw reducer fitted, so basically, I dont need to worry about using either of those 2 options? thanks
MThanks 481, do I need to copy over my user ini file to the downloads location? then delete the other?
Nsuggest just creating a "VPForce-TelemFFB" folder somewhere and moving the contents of the folder in your downloads directory to it. You can place your config.user.ini file in the directory with the new version. It will offer to import the settings into the new config structure (see 4.2.1.2 in the manual).
MOK, have done all that. I have 3 different vpconf files, for different modules (F14, F5 and F18) To enable automatic running of each when I use that module, I went to System/Edit Sim class defaults 7 offline models. I then in the 3rd column dropdown selected all the F14 variants there ( there are 3..?) and scrolled to the bottom to configurator file. I checked this box, then I highlighted the line and used the browse button to navigate to the location of the saved config files ( in my case in "configs" in my main VPforce configurator file location) . On selection, I was returned to the GUI, but there was no where I could see that link was made. Was that the correct procedure for linking a profile to a particular module? Assuming that is correct, I can then in the same GUI edit the Telem FFB effects for that module to differing values using the slider after highlighting each one....correct?
MFinal query ( I hope!) Some of the configs I mentioned aboved were from a buddy. He has some quite different values in the "expert settings" section. I enclose a picture of mine, which I think ( was a while ago now) Walmis recommended. Could I ask that someone take a look at my values and tell me if they are correct? And if not what changes you would recommend and why. many thanks
MI ask as these are different from those in the default config as well as those of my buddy.
NIn the defaults/class editor, after browsing for the file you need to hit the "update value" button, at which point you will see the value updated in the table...
The process is the same for editing any value via that interface.
The process is the same for editing any value via that interface.
Nyou can also make changes while you are loaded in the aircraft via the settings tab in TelemFFB. However, you are limited to the active aircraft here
MThanks, thats clear for using telemFFB effects. What about changing configs in the main VPforce config app for module specific ?I just ran DCS and used the F14, but it did not change the profile being used by vP force config from the default one I had loaded. I used the process as described above.....
Mif you have 5 minutes, it may be quicker and easier if we jumped in the voice channel?
Msave all the pesky typing...!
Ntied up for another hour or so but can after that