Actually just turned on TelemFFB, and without it, spring effect, with it no spring effect
Actually just turned on TelemFFB, and without it, spring effect, with it no spring effect
NAre you loading any vpconf profile via TelemFFB? It doesn’t do anything to affect the spring forces on the joystick axis in DCS.
TOK, just found it on the TelemFFB KB, it is this issue : https://discord.com/channels/965234441511383080/1093558100713279508/1203549616189214784
TNo joy with vJoy, disabled it and it works!
AThe WinWing adapter, can that be used on Virpil’s extensions?
I’m considering a WW stick, but with my current setup I can’t really do without the VPC Z extension, hence the question.
I’m considering a WW stick, but with my current setup I can’t really do without the VPC Z extension, hence the question.
ASo it’d be:
WW grip
+
WW adapter
+
VPC Z extension
+
Rhino
(Best way I can describe it without a poor attempt at using MS Paint)
WW grip
+
WW adapter
+
VPC Z extension
+
Rhino
(Best way I can describe it without a poor attempt at using MS Paint)
Aany chance you got simapp pro working with your rhino? im using the f16ex grip and trying to get it to work as well thanks!
FHi, I'm building a grip. I would like to know the diagram of the mini dim 5 pin connector of the VP Force base to connect it to the controller inside the grip. Thank you very much.
MIs it possible to make VP config & VP telem load an individual profile automatically for different modules?
WHere's the pinout for the TM/Virpil/VPforce interface
FThank you very much
MNice, did not realise we have a spiffy new manual! will get reading!
MMay have a muddle going on.....seem to have 2 folders called VPforce-TelemFFB-wip-dbdbb26f. They have different contents and dates, see screenshots
MOne, which is the newest does not have any config.user file....?
MWhich one do I need?
MMay I also ask ( been reading the manual...) in what circumstances would you use the endstops function & axis rescale and why? The manual expalins what they do, but not why and how you might use them. thanks
WAxis scaling : for example to stiffen controls, to mimic F-16 force sensing somewhat.
Endstops: to (soft) limit travel, the same purpose as the hardware throw limiter, but less reliable.
Endstops: to (soft) limit travel, the same purpose as the hardware throw limiter, but less reliable.
SHey all - sorry if this is a daft question. I'm nearly at the point where I need to buy a DIY kit and was wondering what the difference between all the options are. Any advice on which I should purchase?
Nthe one in your downloads folder is the new file structure
MGreat, I already have the throw reducer fitted, so basically, I dont need to worry about using either of those 2 options? thanks
MThanks 481, do I need to copy over my user ini file to the downloads location? then delete the other?
Nsuggest just creating a "VPForce-TelemFFB" folder somewhere and moving the contents of the folder in your downloads directory to it. You can place your config.user.ini file in the directory with the new version. It will offer to import the settings into the new config structure (see 4.2.1.2 in the manual).
MOK, have done all that. I have 3 different vpconf files, for different modules (F14, F5 and F18) To enable automatic running of each when I use that module, I went to System/Edit Sim class defaults 7 offline models. I then in the 3rd column dropdown selected all the F14 variants there ( there are 3..?) and scrolled to the bottom to configurator file. I checked this box, then I highlighted the line and used the browse button to navigate to the location of the saved config files ( in my case in "configs" in my main VPforce configurator file location) . On selection, I was returned to the GUI, but there was no where I could see that link was made. Was that the correct procedure for linking a profile to a particular module? Assuming that is correct, I can then in the same GUI edit the Telem FFB effects for that module to differing values using the slider after highlighting each one....correct?
MFinal query ( I hope!) Some of the configs I mentioned aboved were from a buddy. He has some quite different values in the "expert settings" section. I enclose a picture of mine, which I think ( was a while ago now) Walmis recommended. Could I ask that someone take a look at my values and tell me if they are correct? And if not what changes you would recommend and why. many thanks
MI ask as these are different from those in the default config as well as those of my buddy.
NIn the defaults/class editor, after browsing for the file you need to hit the "update value" button, at which point you will see the value updated in the table...
The process is the same for editing any value via that interface.
The process is the same for editing any value via that interface.
Nyou can also make changes while you are loaded in the aircraft via the settings tab in TelemFFB. However, you are limited to the active aircraft here
MThanks, thats clear for using telemFFB effects. What about changing configs in the main VPforce config app for module specific ?I just ran DCS and used the F14, but it did not change the profile being used by vP force config from the default one I had loaded. I used the process as described above.....
Mif you have 5 minutes, it may be quicker and easier if we jumped in the voice channel?
Msave all the pesky typing...!
Ntied up for another hour or so but can after that
Mgreat, thanks will ping you in an hour
A@walmis any idea on how that’d work out?
MJust to be 100% clear here as well, I am talking about automatically changing config files to match the aircraft you are flying in VPForce config, NOT the per module settings for the TelemFFB effects.
Nworks the same way... free now if you want to jump in voice channel
Mcool, gimme 2 minutes willl be there
NI've tried 3 different mics on 2 different devices.. issue must be in between or on your side
WIt would work technically, but I'm not sure about the mechanical connection. If the Z extension has a free cable i.e. not a rigid connector then it would be not a problem, otherwise it would be easy to break the WW adapter. In other words if you could mount a TM grip on the Z extension it should be good to go.
MI use a Rhino with virpil Z extension and a hobby built grip with a thrustmaster type mount, it all works fine.
AFor those of you with a winwing grip on your rhino and still using simapp pro will you please DM me and tell me how you got it to work please? 
Fto my knowlede simapp pro does not work with the rhino winwing grip adapter. That communication relies on the "orion" base to work.
Sis it normal that if i import default config my rhino is out of center for like 3 degrees to the right? and if i put endstops afther default apply the endstops are more to the right
AAh I see, thank you.
Si dont know for sure but with those settings my vpforce is going bbbbrrrrrtttt en motor shuting down, those are profile settings for heli that i got from profile sharing, am i doing somthing wrong? or is my vpforce.... 
TTry ditching Friction and Inertia for a start.
WTry damper and spring LPF settings 2Hz and 4Hz respectively
PI think you need to turn down the Friction & intertia LPF Hz. NVM 
why didn't I see the two answers above me? lol
why didn't I see the two answers above me? lolSSo Is it like a lotto ticket for stable motors? Because this are settings from profile share... I really love the vpforce, it's a beast 
but i try to understand why i can not use 3 out of 5 profile share settings
but i try to understand why i can not use 3 out of 5 profile share settingsPI wonder that about the different settings some ppl have compared to others too. It also seems to me that my x axis motor will be the one to shudder & cut out more than the y axis when I experiment with setting changes.
MHow do you edit and save values in an existing vpconf file? I have edited some values in some of mine and they appear to get saved to devices memory when you press store and apply, rather than the actual vpconf file. So when I fly the module again, it automatically loads the previous unedited version. Thanks