PYep, gave one more attempt to no luck. If you could post another cable that'd be great, thanks
WPMade an order request and selected other stating 'USB connector with wiring to motherboard'
BHi all.
I started my DIY journey back in sept 22. And life got in the way.
I am waayyy out of the loop on the project and have forgotten a lot of things.
Few questions.
They standard warthog grip thread is M20?
To make an extension cable, I need to make an adapter from a 5-pin mini DIN to JST- HX 2.5mm correct? Is there a pinout diagram pinned somewhere?
Does anyone know where to get the NS39 Connector, used on the DIY motor kit in the USA? I cant for the life of me find them.
I started my DIY journey back in sept 22. And life got in the way.
I am waayyy out of the loop on the project and have forgotten a lot of things.
Few questions.
They standard warthog grip thread is M20?
To make an extension cable, I need to make an adapter from a 5-pin mini DIN to JST- HX 2.5mm correct? Is there a pinout diagram pinned somewhere?
Does anyone know where to get the NS39 Connector, used on the DIY motor kit in the USA? I cant for the life of me find them.
TWH grip is M36x2.0
Correct on the 5 pin to JST XH.
My kit came with all the connectors other than the JST ones for the peripherals. If your kit didn’t come with the motor leads maybe Walmis could help.
Correct on the 5 pin to JST XH.
My kit came with all the connectors other than the JST ones for the peripherals. If your kit didn’t come with the motor leads maybe Walmis could help.
T
BThanks.
I found the Pinout (I think)
Given that Walmis is super busy, and my order was 2 years ago, I'm thinking my complaint period has closed.
Its just a couple of connectors after all.
If I cant find them, I'll likely solder on some Xt30s or something similar.
I found the Pinout (I think)
Given that Walmis is super busy, and my order was 2 years ago, I'm thinking my complaint period has closed.
Its just a couple of connectors after all.
If I cant find them, I'll likely solder on some Xt30s or something similar.
BIm not sure this pin out matches what @TheAmazinGreat linked..
TAnother one that is a bit easier to read
TThe one I linked is the “male” side. The other one pictured can be a bit deceiving because of the pin numbering in the table since it is out of order numerically on the table but in somewhat of a numerical order on the picture.
BWill the 6pin PS/2 cable work fine?
TYou might be able to make it work by modifying since the nub in the middle is different between the two. I just got some off digikey, might be able to get those NS39 connectors there too.
BI ordered some 6 pin female panel connectors, I found a datasheet drawing of the 5s and 6s connectors. The difference is very minor.
Pretty sure I have the XH connectors in my RC stuff.
Xt30s to change out the motor power connectors. Since i have the 86 size motors. and a 300w PS.
Ordered 20amp resettable breaker,
What else....
Pretty sure I have the XH connectors in my RC stuff.
Xt30s to change out the motor power connectors. Since i have the 86 size motors. and a 300w PS.
Ordered 20amp resettable breaker,
What else....
B@walmis
i have a single motor connected on the bench, and It looks like VPForce doesnt recognize its connected.
i have a single motor connected on the bench, and It looks like VPForce doesnt recognize its connected.
BDo I have my connections right?
Ndisable the axis thats not connected
Biv tried disabling each axis one at a time. no luck.
it says in bottom right i have no motors connected
it says in bottom right i have no motors connected
Nyea, I see that now.... if you've verified the motor is getting power, I'm not sure what else to look at. The wiring isn't complex and looks right to me.
Bill dbl chk power
JI am not 100% sure but I think I saw someone with a similar problem some time ago and I believe it was that the motors are labeled X or Y and have to be plugged in as such into the M/B.
Blooks like power issue, though i dont know what could have happened between last night and today to make it not work anymore
NIIRC, there’s a green LED on the motor in the cavity where the connectors are. But I’m not sure if it’s just a power indicator or a board communication status indicator.
Nanyone had issues with the xplane 12 zibo 737 with control jitter while running telemffb?
BWould this explain my power supply not working?
Nyou are very likely the first person to try, to be honest. What you describe sounds like the axis position that TelemFFB is sending is fighting with what X-Plane is reading. The xplane plugin for TelemFFB sends the commands to override the axes, but there is a lot of unknown about how different 3rd party modules are implemented in xplane. Even the default R22 helicopter doesn't listen to the override command for the collective axis. It is entirely possible that many of the more advanced 3rd party aircraft won't work.
You can try disabling the axis control in TelemFFB and see if it clears up (this will also disable any trim/autopilot following). You can also try un-binding the axes in X-Plane.
You can try disabling the axis control in TelemFFB and see if it clears up (this will also disable any trim/autopilot following). You can also try un-binding the axes in X-Plane.
Naxis control was definatly the issue thankfully still useable without.\
HPlease help, I’m not getting any ffb on il2.
HThis is from rhino debug log
Nexplain more what you mean. There is nothing abnormal in that debug tab output
HWell I hoped it would work out of the box. I checked that ffb was enabled and everything else is default. In game I only have the rhino spring feeling, no ffb, rumble etc
Nthe native FFB in IL2 is limited to:
- Dynamic spring force based on airspeed
- ground bumps
- gunfire
- stall buffeting
FDid you use the TelemFFB?
Ntelemffb only adds supplemental and alternative (to the three I mentioned) effects. The actual 'FFB' (dynamic stick forces, trim following) are %100 handled by the game.
HNo telemffb, but it is not required right?
HDo I need to enable the effects in rhino to be overrided by the game?
Npost screenshots of your configurator effects and settings tab (win+shif+s for windows snip tool is your friend, vs pictures with your phone)
HYes I know I’m on a new setup and did not have Discord app installed yet
HOk there are ffb effects but they’re so weak it’s barely noticeable. 85% periodic effects and the stick barely vibrates when shooting. I guess I just need to crank everything to the max
Ncheck the "shake" slider in the IL2 FFB settings. It defaults to max, I believe, but just in case... Also your Periodic LPF value in the configurator expert settings will have an impact (default is 20Hz I believe).
HOk, thanks!
BIs there a setting to tighten up the center of the stick? When in top dead center it feels like ther is no resistance for the 1/8 inch all directions. There is just a little more play then I perfer and rather not have to set a big dead spot in game settings.
WIt's possible to tune the center using the spring mapping tool
WAlso "adaptive recentering" will help keeping it centered
BOk, thank you! I'll give it a try.
BI have ordered a replacement thermal Varistor,
But can someone tell me what this is?
But can someone tell me what this is?
Nlooks like it used to be a fuse?
Nwith the glass tube blown off? wild ass guess