Quick Question: How many VP devices (by circuit boards) can be operated at the same time? Is there a
Quick Question: How many VP devices (by circuit boards) can be operated at the same time? Is there a limit?
N6, I think. Only because you are limited to PID=2050 to 2055 in configurator. No idea there's a reason for that other than walmis probably never considered anyone would even have 3 going simultaneously 
Hthank you!
THi how do I see where I am on the list to purchase
Fyou need to ask the bot.
https://discord.com/channels/965234441511383080/986474224241741884/1048909362028093450
https://discord.com/channels/965234441511383080/986474224241741884/1048909362028093450
SNot sure where best to post this, but I'm all set to receive my Rhino. Order is paid, and I think there's a few orders ahead of mine. I am concerned about when it will ship however. I travel for work every month. Who can I coordinate with to ensure that, when my order is ready, it ships so that it arrives when I am home?
AWalmis can probably try to help you, but in the end it's up to the delivery company to get it to you on time
TI would contact Walmis and ask for a delayed shipment.
Tell him the day you return so it can be shipped while you’re home and can deal with any local taxes or shipping fees directly.
Tell him the day you return so it can be shipped while you’re home and can deal with any local taxes or shipping fees directly.
SI'll reach out. Thanks
PAnyone else using the Jetpad or Sim Shaker for Aviators & getting problems with vpforce config app freezing?
PAlso getting a creaking sound in my gimbal recently
L@walmis Any idea why TelemFFB created a 68 GB log file?
LGot the text file open looks like it loops an error when TelemFFB is running and the device is disconnected, over 600,000,000 lines of code as it pushes a log every millisecond:
WThe latest version should handle device disconnection properly and attempt to reconnect. The log size is quite amazing though 
S
Plooks like you have the making of a zip bomb there
TWith damper enabled, I keep getting oscillations and shutdown. I've been messing with LPF tuning etc. and have reduced it where I dont get the shutdown for just touching the stick. However, I still get slight vibration/oscillation but only in the x-axis, yaxis is smooth. Any suggestions? Trying to fly DCS Apache. When I get the ETL vibration effect from TelemFFB, it goes bananas and vibrates strongly until I shut it off and back on.
KMy Motor Y stays offline. I have removed PSU and USB, but it stays offline.
In the last 3 days the motors went offline 3 times when I was playing DCS.
But ever time they come back online after moving a axis to full aft/forward.
Any ideas?
In the last 3 days the motors went offline 3 times when I was playing DCS.
But ever time they come back online after moving a axis to full aft/forward.
Any ideas?
WTry damper filter at 4Hz, but yeah it shouldn't be this sensitive at those settings. Check the belt tension on the X axis too.
WMy bet would be to check the wiring, see if wiggling the data wires near the plugs give some connected/disconnected beeps. Also check if the motor LED blinks steadily when powered.
TThis is where I ended up through randomness. I would like to know how the dynamics interact between Spring force and damper with respect to LPF and the sliders. My objective was a spring centering, damped feel that reflects the slowness observed by the reaction of controls in DCS apache vs. the actual stick. If I deflect the stick and let it go, it lightly bounces like a spring on it's way back to center, but I have the damped feel/look I wanted.
RMine creaks in both x and y, but i havent had any issues and everything is tight.
TI think someone lifted up the leather boot and tightened the bolts at the TOP of the metal tube connector?
It was long ago but someone fixed this creak by doing that and I think the culprit was the square metal tube and those screws.
Maybe a search and you can find the pic of what screws he tightened
It was long ago but someone fixed this creak by doing that and I think the culprit was the square metal tube and those screws.
Maybe a search and you can find the pic of what screws he tightened
TSee above sorry I forgot to tag ya 
TSee above above and good luck!
WHas anyone noticed the force in one of the axis for the motor going bad? I think my Y-axis motor may be going bad
WThe level of force is much less than X axis, all settings have each axis at 100%
WAlso, is there a way to reduce pot_2 to 0%? I don’t have it bound to anything, but it’s been sitting at 1.2% and changes to 0.7% if I scroll the potentiometer to 0.0% for pot_1.
WIf I hold it in full deflection at full spring strength the fans kick on in 10 seconds, climbs to 60 deg C, X axis motor is fine.
WMy guess is that the motor was preheated from earlier and does a bit of thermal throttling, it shouldn't be going 'bad' - it either works or doesn't
In the off chance - it could be a thermal paste issue between the motor and transistors on the driver pcb that impedes heat dissipation into the motor, that causes it to register higher temperatures.
When pot_2 is unconnected it floats a bit due to high electrical impedance, but if it's disabled in software it doesn't do anything regardless
In the off chance - it could be a thermal paste issue between the motor and transistors on the driver pcb that impedes heat dissipation into the motor, that causes it to register higher temperatures.
When pot_2 is unconnected it floats a bit due to high electrical impedance, but if it's disabled in software it doesn't do anything regardless
WOkay, thanks Walmis. I don’t know how it could have been preheated, but I’ll keep an eye on it.
Awhat were you flying btw?
Aand were the fans running?
MI'm about to confirm my order at last (YAY!) - but now I'm wondering: what is "13. Machined Aluminum Grip Mount Upgrade for Rhino, Anodized, Black" used for - do I need this?
TFirst congrats! I’m really excited to see another baby Rhino in the wild.
For questions like that to get a quicker response I would go ahead and tag @walmis
For questions like that to get a quicker response I would go ahead and tag @walmis
BThe normal mount is simply 2d printed, and if you have an accident and get a grip or extension even a slightly bit crooked on, you will quickly shear off the thread as you basically just attacked it with a dull burr tool.
TIt’s an upgrade to the grip attachment threads from 3D printed to Aluminum.
BI managed to do just that, do have an aluminium piece now, but i also managed to 3d print a replacement two days before it arrived so haven't actually fitted it yet.
I honestly think it would be a decent upgrade for the most often worn/broken part on the whole rhino.
I honestly think it would be a decent upgrade for the most often worn/broken part on the whole rhino.
Adepends a lot on how often you intend to switch grips
MAh Ok, thx everybody. I have two grips at the moment, probably more to come… a sturdy thread seems to be a good idea 
AI've got a problem with my Collective. Everything worked fine until next week, suddenly i get a FAULT_ENCODER_MAGNET Error as soon as i power up the Collective. When i set Master Gain to 0% and restart, everything is fine. As soon as i increase the Gain to around 30-50 % the Motor times out again with the same error. I'm using the swap function to get an X mtoro to run as an Y. But, the Collective has been working like that for at least 2 months now without any problems. Any suggestions on how to fix this?
WYour damper force LPF is 0Hz for some reason, set it to 6Hz and it should be fine
AThat was quick! And it worked! 
Thank you! No idea what changed it to 0 though.
Thank you! No idea what changed it to 0 though.TJust for myself the standard setting for Rhino is 4Hz?
But yeah never 0 right? I need to re watch your set up video again
But yeah never 0 right? I need to re watch your set up video again
PHey guys if I've got a Virpil Warbrd grip & getting all FFFFF in the grip debug does that mean I might not have the grip plugged in properly?
Palso I have no virpil base just the Rhino
Pgot that working, need to really seat the plug in on the virpil
Dnoticed this option doesn't work in latest update
D
DI had to download the configurator separately to run it
Nseems to work fine? The configurator isn't bundled with TelemFFB or anything. It needs to be installed on your system and you need to have run it at least once (so that it sets its own path in the registry which is how TelemFFB finds it).