TM is already supported, and Walmis has said directly that FLNKR will be supported.
TM is already supported, and Walmis has said directly that FLNKR will be supported.
SCan’t find the any TM grip listed on the configurator pulldown selector, how do I access them?
T“Generic Grip”
TWill work for all CD4021B shift register based grips.
GHi everyone
GThe vkb apdater will that work on a moza ab9?
DI recently started using a physical throw limiter. After calibration the axis all match up correctly in the configurator, but once I get into certain modules the y axis is rescaling by itself. The full Y axis throw is limited down to 50% once the ffb telem kicks in. The limited range is reflected in the configurator and in DCS. If I close out FFB telem I get the full axis again. I have nothing in the effects tab of the configurator turned on. Any help would be appreciated. Thanks.
KDid you use TelemFFB to load an old configuration file?
VHow do I setup trim stick following for DCS OV-10A mod? In game elevator and aileron trim work but stick doesn’t follow trim input.
Nthe community mods (excepting the OH6) don't support FFB. You'll have to either use "Sticky" spring + override trim in the configurator software, or you can use the "Override DCS Spring" feature in TelemFFB and then set your trim bindings in the sub config.
VOk I’ll give that a try. Thanks!
VWill any of the telemffb effects work with the OV-10
V?
NMost stuff should work. I think.
VOkay. Something to play with. 
DI dont believe so. So what I noticed today is that its for aircraft that have asymmetric y axis. the F18n has about twice as much pull as it it does push. Whats currently happening is the pull side of the Y axis is being reduced instead of shifting the center point forward.
KThe F/A-18C in DCS has no asymmetric y axis. I have that problem with the A-10CII if I use curves. And I've read the F-5 has the same problem. But F/A-18C in DCS works for me without any problem. But I use virtual end stops and axis resizing at the moment. But I will create a physical end stop soon.
Vso after adding force comp. my stick starts to oscillate on the x axis what can i do to go around that? i only get it when i put force comp im pretty new sorry the questions
AUpdate on this issue - happened while not running Configurator but has not happened since cutting TelemFFB out (4-5 flights).
IIs it possible to upgrade the motors in the Rhino? DCS WWII fighters , the stick gets real soft after a while dogfighting, and the fans turn ON. More powerful motors should help with tis issue.
TNot possible in the stock housing, requires an upsized case. https://discord.com/channels/965234441511383080/1145651561578647582/1284569338996850828
CCan someone explain what I need to tick to make hardware trim work in dcs, trying it out on the viggen and the stick moves the wrong way when I trim. VKB grip.
IBummer, so will need to sell mine and buy a Monster Rhino , have you tried the stronger motors? worth it?
CCant find it in the manual
CWhat do you mean hardware trim in the Viggen?
CI mean, when I trim nose down, the stick travels backwards, and becuase everything is off center after trimming, the "autopilot" cant be engaged, since letting go of the stick will command nose up or down if you have used any trim
CSound like you trim bindings are backwards
CThey are good ingame, any way to flip them in the rhino sw then?
CWhat else did you change in DCS or Vpconfig? This is not the normal usage. I just trim like normally and my stick follows
TI have, but have never tried the standard Rhino to compare to. The regular 60/15 gear ratio of the monster makes it about 1.7x more torque than the standard Rhino but I recently upgraded to 72/15 which is just a hair over 2x the torque of the standard Rhino.
TThe Winger kits are in fact kits though, so you do have to assemble yourself. Plus buy the 86 series motors from Walmis.
TMake sure if you are inverting your pitch axis that it is inverted in the VPForce configurator. And not inverted in DCS.
CAble to fix it?
CI tried the F4, there everything works out of the box. But for the viggen the stick moves the wrong way when trimming
N1.) Make sure your axes move correctly in configurator. If one or both are backwards, invert them in configurator, not the sim.
2.) if the trim is backwards for an aircraft, invert the axis in the FF Tune for that axis. Pretty sure the F5 x axis needs this treatment, there are probably others I don’t know about.
2.) if the trim is backwards for an aircraft, invert the axis in the FF Tune for that axis. Pretty sure the F5 x axis needs this treatment, there are probably others I don’t know about.
CWhat are we talking abouth ere ? FF tune? Is that Telem FFB?
CIm reading something about inverting FFB axis in DCS. But I can not find any options for that in the game
NThat’s cause DCS retarded. You have to uncheck the “foldable view” in the controls binding, then you will see the FF Tune button
HHey. It is. Still it deserves love! 
NTough love
COk down at the bottom, after you have selected the regular axis inside
CNever know those options exsited really
CThanks a lot, now it works fine 
DAre you sure this is the case. Maybe Im not describing in correctly. Sorry for the warped view from VR. The control indicator has more travel on the bottom than the top. I seem to have sorted it out with some axis rescaling. Is there a way to have it just set the neutral position like the F5 does? without having to tweak the axis scaling for different aircraft?
NSend over your TelemFFB config if you want, here or DM me (Help->Create Support Bundle).
Did you verify if it is the actual in-game trim that is running away? Should be able to see the trim position moving un-commanded if that is the issue
Did you verify if it is the actual in-game trim that is running away? Should be able to see the trim position moving un-commanded if that is the issue
AYes, last time it was full nose down trim and that trim indicator was all the way at the top
AI'll send it to you tonight after class 
NHmm. Yeah, there’s nothing in TelemFFB that sets the trim. Even if you were using the hardware trim in the spring override feature, that doesn’t change the trim value…only the spring center.
I don’t even think it’s possible to externally set the trim in DCS.
Send over your Telem config anyway and I’ll have a look at it.
I don’t even think it’s possible to externally set the trim in DCS.
Send over your Telem config anyway and I’ll have a look at it.
AWonder if something in my DCS install is corrupted then because I even deleted the keyboard trim bindings just to be sure there was nothing else that could input
*Guys... did anyone design a plastic cover for the front cable & power connectors...?
I already stumbled over those protruding cables and it's gonna get wrecked if I do it again...
I already stumbled over those protruding cables and it's gonna get wrecked if I do it again...
KI turned my Rhino, so the connectors are on the backside.
Also you can buy angled usb & power cable/adapters. This helps, too.
I didn't see a cover for them here.
Also you can buy angled usb & power cable/adapters. This helps, too.
I didn't see a cover for them here.