RTell me about it. But I managed two years ago when I bought my WinWing F16 stick and throttle and had her also gift those to me. Just glad she allows me to spend like this on my hobby, albeit in the guise of a GREAT Christmas gift. My VP saga began back in early March with my placing my Rhino order and now it will continue until Christmas. So be it.
Sjust plop it on the kitchen table unplugged and play with it, making airplane and pew pew noises for a while.. eventaully she'll say fine! go hook it up!
SDoes anyone know if FS2024 is going to be supported by telemFFB or if we will have to wait a while?
SI tried my rhino with the tech alpha of 2024 and it was shockingly bad. Not through any fault of the rhino, just not the best stick to test a new sim with
Sit worked mostly fine for me.. there was some issues when in career mode when the cutscenes were going though.
NWorks exactly like it does for 2020 while flying. As smitty said, there’s some issues (with 24) during some of the menus where simconnect is not “paused” and it seems the aircraft is flying or taxiing somewhere off screen. Not sure how we’ll address that (or if the issue will even exist at release)
BDefault is you need to calibrate them every time the computer starts, simply push it to full limits on all axis including brakes. You can turn it off in the software, I found out like you lol.
OCool.
At least it’s not fucked lol.
At least it’s not fucked lol.
MHello! Is it possible to order the rhino with a differently shaped stick/shaft (the part that the grip attaches to)?
MDue to my seat slider lever I would have to install the rhino a bit away from the seat (the stick/shaft would be like 8 cm away from where the thigh support ends)
Ideally the stick would be the same or similar height, but offset 8-10 cm towards the closer end of the box (the one with a gear)
Ideally the stick would be the same or similar height, but offset 8-10 cm towards the closer end of the box (the one with a gear)
MI thought about extensions but they would place the grip too high
MThank you
Msomething like this
DYes, there are various offset extensions you can find. Either purchase from your grip supplier, or else 3D print one yourself from your design or somebody else's existing design.
MI do not want to use an extension
CYou can build your own with any modifications you want 
FThen you'll have to redesign the middle connector
MQR4rigs, Quick Release Mounts for Sim Rigs Joystick Extension for Rhino 50 x 80 [StickExt50Rh80] - This joystick extension is designed exclusively to fit the the VPforce Rhino with the standard or metal stick connector and is for use with Thrustmaster Warthog/Cougar and Virpil (VPC) joystick grips. The main tube is 30mm in diameter and extends t...
![Joystick Extension for Rhino 50 x 80 [StickExt50Rh80] : QR4rigs, Qu...](https://images-ext-1.discordapp.net/external/8WqKHOg1iUmvmOcJTwBWJbnilWQwBpxFi08PbZhR_40/https/qr4rigs.com/includes/templates/mrpix/images/weblogo.jpg)
MI guess this is minimal height added possible
MCould someone please measure how far is the center of the connector from the closer end? Seems like around a third of the way, so 7-8 cm
FYou can try to argue that you need 10 weeks to configure the device and then start playing at Christmas... 
MThat is a fair point though, I assume getting this to be perfect for a given sim/plane of preference is some work
Hif you mean in the horizontal plane, it is exactly 6,5 cm on the short end and sides (not accounting for the belts).
H11,5 to the long end. The Body of the Rhino is 180 190 (sorry, memory fooled me) by 130 and the Gimbal is 130 by 130.
MI have to account for the gears/belts too
MI assume they're 2.5 cm each?
HThe Production Rhino comes with 10mm Belts afaik. Plus clearence on both sides - lets say 20mm total. The Kit-Rhinos use 15mm belts,
HI turned my Rhino 90 degrees to have a short side without belt close to my chair for that very reason......
MI mean the vpforce rhino
Says in the documentation that it's 205 mm long
Says in the documentation that it's 205 mm long
M
MI mean the distance from left end of the belt to the center of the stick
MIf the body is 180 mm and doc says body + belt is 205 then the belt has to be 25 mm but it seems like a bit too much so something is off
M@Hiob do you happen to use a quick release?
MI won't really be able to use the quick release I found sideways, and I will need it... But it seems that the mounting holes on the rhino are spaced only 0.32 mm differently when turned sideways
MI wonder if that will fit if I keep the QR orientation the same but rotate the rhino. Doesn't seem like too much of a difference
HSorry, my memory fooled me. The body is 190 by 130
Hno, but I made several custom modifications to my Rhino, including the base plate.
FAs far as I know the qr4rig quick releases have a modular design - that means if you create the plate between the Rhino and the quick release plate yourself (3D printing, wood) you can freely choose placement and orientation (e.g. QRUHD Universal Quick Release Plate Kit (DIY) and using the hex pattern https://qr4rigs.com/index.php?main_page=product_info&cPath=24&products_id=140).
QR4rigs, Quick Release Mounts for Sim Rigs QRUHD Universal Quick Release Plate Kit (DIY) [QRUHDUniQR] - This QRUHD Universal Quick Release Plate Kit is designed to allow mounting of unsupported controllers on to our QRUHD Quick Release System and also provides a stable surface for mounting our QRDee Base Mount 40 or QRPro Base Mount 40 to enable...
V:package: 
RHINO #0738 Has Shipped!
RHINO #0738 Has Shipped!V:package: RHINO #0736 Has Shipped!
RHINO #0736 Has Shipped!V:package: 
RHINO #0737 Has Shipped!
RHINO #0737 Has Shipped!
WIT’S HAPPENING!!! 
I got an aircraft number too, lol, though the one plane I won’t be using it with. 
I got an aircraft number too, lol, though the one plane I won’t be using it with. 
FAlmost 300 units since I got mine this year. Mental
AI don't feel like a unique snowflake anymore
FFFB becoming mainstream in flight simming. Lol
BDo newer Rhinos (SN 0656) have fans at all? When I test this with the VPforce_FFB_Configurator nothing seems to happen.
WHas come a long way mine is SN 0078 lol
LSN 0072 says hello 
FI do, but only cause I made one myself (should've chosen a more rugged gimbal though, meed some time to rectify that)
HI would be puzzled if not. You should be able to see it through the grill though. Have you tried the in the debug page?
