I cannot get force trim to work in the Huey. The joystick always falls back to original position whe

I cannot get force trim to work in the Huey. The joystick always falls back to original position when I release it. What's the magic to get it to obey the force trim reset button?

SSudeebare I cannot get force trim to work in the Huey. The joystick always falls back to o...

Zrad•12/5/24, 2:21 AM

Is your trimmer mode set to something other than default in the special settings?

SSudeebare I cannot get force trim to work in the Huey. The joystick always falls back to o...

Number481•12/5/24, 2:24 AM

Setup is pretty simple...(telemffb not required but thats the channel this was posted in) https://discord.com/channels/965234441511383080/1230852705593851964/1304566389519945810

Note that this person's issue turned out to be their USB hub. After connecting the Rhino directly to the PC it started working fine.

VPforceBot•12/5/24, 1:15 PM

:package:

RHINO #0820 Has Shipped!

VPforceBot•12/5/24, 1:15 PM

:package:

RHINO #0818 Has Shipped!

VPforceBot•12/5/24, 1:15 PM

:package:

RHINO #0817 Has Shipped!

VPforceBot•12/5/24, 1:15 PM

:package:

RHINO #0821 Has Shipped!

NNumber481 Setup is pretty simple...(telemffb not required but thats the channel this was p...

SudeebareOP•12/5/24, 5:38 PM

Finally got Pilot Trimmer working. This after a lot of fiddling in the Configurator. I finally got the grip balanced with dot in blue circle. Not sure whether that was necessary but now the trimmer button works as expected. Pot#1 is at 15%. Thanks!

TonyZ2525•12/5/24, 7:02 PM

@Sudeebarewhat are the exact settings u used for inside dcs on the huey and which control in the settings did u set buttons for to get it all to work?

SudeebareOP•12/5/24, 9:57 PM

Inside DCS as in image above. In Effects:

907basebal•12/6/24, 7:25 AM

What’s the current wait time for the pre-order list?

9907basebal What’s the current wait time for the pre-order list?

Alighierian•12/6/24, 7:39 AM

📃general

AAlighierian https://discord.com/channels/965234441511383080/965234441511383083/1313409610446...

907basebal•12/6/24, 8:21 AM

Thank you

VPforceBot•12/6/24, 3:18 PM

:package:

RHINO #0824 Has Shipped!

VPforceBot•12/6/24, 3:18 PM

:package:

RHINO #0822 Has Shipped!

VPforceBot•12/6/24, 3:18 PM

:package:

RHINO #0823 Has Shipped!

Flintlocke•12/7/24, 1:11 AM

Hi guys, quick question: Does anybody use the Rhino with the WinWing F16EX with shaker kit? Is the Shaker somehow also supported by the platform or is it superfluous?

Alkman•12/7/24, 1:21 AM

I had the opportunity to test the Moza Mh16 Grip and would like to buy it. I love the Warthog stick but it wheighs 1.2 Kg. The Mh16 is only 570 gram made of Aluminum. Do you think it works out of the box with the Vpforce Controller like the Warthog as a Generic Grip?

FFlintlocke Hi guys, quick question: Does anybody use the Rhino with the WinWing F16EX with ...

TrigaNZ•12/7/24, 4:25 AM

Don't think it is, I don't feel the need for it anyway.

AAlkman I had the opportunity to test the Moza Mh16 Grip and would like to buy it. I lov...

Kite•12/7/24, 8:00 AM

You should know that MOZA isn't very popular around here since they stole VPforce source code for their FFB base software.

AAlkman I had the opportunity to test the Moza Mh16 Grip and would like to buy it. I lov...

Hiob•12/7/24, 9:07 AM

The weight of the Warthog grip isn’t an issue whatsoever though. I use it, and I‘m pretty sure lots of others, too. So if you worried that the weight would be an issue for the Rhino - you don’t need to.

HHiob The weight of the Warthog grip isn’t an issue whatsoever though. I use it, and I...

Alkman•12/7/24, 10:00 AM

It is an issue when you mount it with a long offset extension on a Motion Rig. Lot of work for the Motors, less agility difficult to recenter the stick with Motion active. I didn't now that they stole a source code. Only talking about the Stick, not the Base since I already build 3 Vpforce Bases. My question is, will the Stick that is compatible with a Thrusmaster Base, also work with the Vpforce controller? If it is forbidden to ask about Moza then sorry about that and forget my Question.

AAlkman It is an issue when you mount it with a long offset extension on a Motion Rig. L...

Hiob•12/7/24, 10:06 AM

I‘m using the Warthog on 20cm gooseneck. (No motion rig though)
I doubt that the motion rig would introduce any issue, but I can’t know of course.

Alkman•12/7/24, 10:11 AM

That's nice for you but I had trouble with 1.2kg mounted on a 10 cm offset extension with 15 cm height. Force Trim was not funny with Motion active.

Alkman•12/7/24, 10:38 AM

@Kite thank's for that Information, I didn't now that. But other question, I see the last Pictures of your v2 throttle mod, how it's going? Are you done with it? Can't wait for that extra leverage

Every day I see the last unmodded thing on my Rig

FFlintlocke Hi guys, quick question: Does anybody use the Rhino with the WinWing F16EX with ...

R7-Cedar•12/7/24, 11:14 AM

If you meant the shaker kit as 'expantion body' for the joystick featured in https://boostedmedia.net/flight/winwing-16ex-metal-joystick-grip-with-shaker-kit-review/
, then it's working fine for me except button 41 and 42. I haven't tried every possible settings/axis though. I use it mostly for DCS. Ka-50 might be one of the module use most out of this expantion.
I agree the naming 'shaker kit' is confusing. I don't care internal vibration motor came with WW joystick niether, while much nicer FFB/telem-effect is going strong.

Boosted MediaTom Ford

WINWING 16EX Metal Joystick Grip (with Shaker Kit) Review

Detailed review of the WINWING 16EX Metal Joystick Grip with shaker kit by Pilot and Flight Sim expert.

Kite•12/7/24, 11:23 AM

It's going well, new prototype next week. @Alkman

AAlkman It is an issue when you mount it with a long offset extension on a Motion Rig. L...

TheAmazinGreat•12/7/24, 11:55 AM

If a stick works on a TM base it will work on the Rhino as generic grip. Read this thread under the functions section and there is some info on trying the moza on other bases. It sort of works but the hats are messed up. https://forum.dcs.world/topic/364801-moza-mh16-review/

TTheAmazinGreat If a stick works on a TM base it will work on the Rhino as generic grip. Read th...

Alkman•12/7/24, 12:33 PM

Thank's for the Link !

RoboGeoff•12/7/24, 3:38 PM

I still prefer a lighter grip, even on the Rhino. I've used both Realsimulator and Tianhang on a 10cm extension and this was the way to go for me

Bob Bushman•12/7/24, 5:59 PM

Think my virpil grips is like 300gr. And i don't mind thst it isnt form factored to something I fly as i have nearly 40 buttons to bind.

spart_sk•12/8/24, 1:05 AM

Hello guys how long is approximately wait for the rhino? I will have budget for it the next year. But I am thinking about joyining the que now, as wait time is in months? Or not...?

Sspart_sk Hello guys how long is approximately wait for the rhino? I will have budget for ...

Zrad•12/8/24, 1:10 AM

📃general

Mike T•12/8/24, 11:15 PM

Does anyone by any chance have a step or obj file for the 57BLF03 motor to use in 3D modelling program for a design I’m working on? Ta

MMike T Does anyone by any chance have a step or obj file for the 57BLF03 motor to use i...

smitty•12/9/24, 12:19 AM

57BLF03.STEP393.65KB

Mike T•12/9/24, 2:14 AM

Thanks

HHiob Click to see attachment

Zrad•12/9/24, 3:59 AM

I use a 20cm gooseneck as my extension too, and started with your setup as a starting template. Do you use the "Low Hydraulic Pressure Effect" in TelemFFB, and if you do, how do you setup the damper/inertia/friction overrides?

ZZrad I use a 20cm gooseneck as my extension too, and started with your setup as a sta...

Hiob•12/9/24, 8:16 AM

I don’t use neither of those effects, sorry. I set inertia friction and dampening only once per class (fixed wing or helicopter) in dedicated vp config profiles. And I haven’t tried the low hyd press effect yet.

VPforceBot•12/9/24, 1:22 PM

:package:

RHINO #0826 Has Shipped!

VPforceBot•12/9/24, 1:22 PM

:package:

RHINO #0825 Has Shipped!

flasper•12/9/24, 4:51 PM

Do I need to run both TelemFFB and FFB Configurator when playing DCS?

Bob Bushman•12/9/24, 4:57 PM

Not necessarily the configurator but it is where you would change and tune core parts of the stick, don't really see any reason not to

Fflasper Do I need to run both TelemFFB and FFB Configurator when playing DCS?

Hiob•12/9/24, 6:32 PM

Usually I have VP config running (two instances for pedals and stick) while playing to tweak the profile if necessary.

Bob Bushman•12/9/24, 7:06 PM

Might also be my paranoid behind, but I also like having usbtreeviewer running in admin mode as well.

andyn•12/10/24, 3:01 PM

fedex'd again. "delivery not attempted"

mark turner•12/10/24, 4:14 PM

Where and how is it best to adjust in the software to make the stick a little less responsive as you might do by adding a curve in the DCS axis settings on a normal joystick........?

VPforceBot•12/10/24, 4:45 PM

:package:

RHINO #0828 Has Shipped!

VPforceBot•12/10/24, 4:45 PM

:package:

RHINO #0827 Has Shipped!

ToreDL87•12/10/24, 11:11 PM

I've been having issues with the VKB adapter, I've tried connecting it to the MK1 Blackbox and MK2 Blackbox, and flashed them accordingly, but I can't use the KG12 grip or the TM Warthog grip (w/VKB adapter)

ToreDL87•12/10/24, 11:12 PM

The red "Stick" light on the blackbox keeps flashing.
And obviously I can't ask VKB for help here, the adapter is VPForce after all, so I was just curious what the procedure is here.

ToreDL87•12/10/24, 11:47 PM

This adapter specifically.

I cannot get force trim to work in the Huey. The joystick always falls back to original position whe

Similar Threads