Good to know, thanks! And yeah I've definitely enjoyed a few beautiful moments when I had essentiall

Good to know, thanks!
And yeah I've definitely enjoyed a few beautiful moments when I had essentially bound every last button required to do a full F18 cold start, so I could go through the whole sequence without ever clicking something with a mouse.

But that does get old when you have to wait 8mins for INS alignment and you kinda just want to fly

G. R. Cooper•1/30/25, 2:05 PM

Stored Heading is the way!

elijahautistic•1/30/25, 9:20 PM

Hey ! I was wondering if some of you have a very little play on the roll axis (or pitch, depends on how the gimball is mounted i guess)

I can’t really describe it nor show it on camera, but let’s say for example. You roll left and suddenly go right, i feel a very little play.
My guess is that this is just the design of the gimball that creates that

TheAmazinGreat•1/30/25, 10:13 PM

I would tend to agree. One direction will be direct acting and the other direction transfers through the core joint. I think the core joint is where the play comes in. If not play, it is at least extra flex. I also assume this is why you can see different values for force comp on x and y axis in the default configuration.

Rocco Thamanoidis•1/31/25, 5:05 AM

Unfort. the motor timeout/disconnect bug is back. Even with MSFS 2020/24 support disabled.

Rocco Thamanoidis•1/31/25, 5:08 AM

and here at 4:16 compared with the TelemFFB log on the left

Rocco Thamanoidis•1/31/25, 5:09 AM

and at 4:12 also side by side logs

Rocco Thamanoidis•1/31/25, 5:20 AM

Mostly on low demand situations like rollout on runway or hovering. Only 1 time in this session under load.

HHavebug I guess you can have a similar workaround by placing a capacitor in parallel at ...

Rocco Thamanoidis•1/31/25, 5:22 AM

Nice, but this requires soldering and opening the product. Not gonna happen for me. I hope for the software solution.

RRocco Thamanoidis Nice, but this requires soldering and opening the product. Not gonna happen for ...

Havebug•1/31/25, 6:07 AM

no need to open the product... I mean something like this:

Havebug•1/31/25, 6:09 AM

I remember I suggested this to @I-WVoss as well that had a similar issue...

GGTOfire Sanity check: I'm finding it super convenient when I hop in and out of my rig to...

Nemisis Wolf•1/31/25, 8:32 AM

The Big Red Button only disables the motors it does not "SWITCH OFF" the internal electronics. If you are not switching it off at the wall or disconnecting the power cable from the power brick then the internal electrics going to the circuit boards are still powered up! Hitting the Red Button to move the Grip out the way is fine to help you get in and out of your Pit but you should always switch the power to the power brick off as you'll get software issues and bugs showing up as the circuit boards are on all the time! Had this issue after the first week of having it.

Shutting it down completely to reset everything solved issues I was Having!

GTOfireOP•1/31/25, 8:34 AM

Oh yeah whenever I stop my session I fully disconnect both the USB and power to the rig, since I then have to wheel it away. This is just for getting in and out more conveniently

Nemisis Wolf•1/31/25, 8:36 AM

My Current issue now is I have no trim effects for Stick or Rudders in DCS making it impossible to fly!

frumpy•1/31/25, 10:07 AM

I exchanged the grip mount to an aluminum one, just to find the play between the grip mount metal profile coming out of the Rhino increased. The plastic mount was tighter. I could tighten the screws more, but I fear I'll destroy the threads. So I am thinking about glueing the mount to the profile. Is there any significant risk that I am taking? I should still be able to disassemble the Rhino, if needed, or?

Ffrumpy I exchanged the grip mount to an aluminum one, just to find the play between the...

Fr4Ged•1/31/25, 10:27 AM

I'd use something like plumber tape before glue.

NNemisis Wolf The Big Red Button only disables the motors it does not "SWITCH OFF" the interna...

smitty•1/31/25, 2:20 PM

been running almost 2 years here with only cutting the 24v power, usb always connected and pc remains powered up. no issues.

Ssmitty been running almost 2 years here with only cutting the 24v power, usb always con...

Nemisis Wolf•1/31/25, 2:33 PM

My issue was that for the first week I had it, I was just hitting the Big Red Button BRB from now on. and after a week FFB was just not working as it should. Realised the BRB was just cutting the power to the motors but leaving everything else fully powered. Unplugged for a minute and all went back to normal and have unplugged from power brick ever since. USB still connected to PC but I do shut it down at night. Been good ever since until recently and the F-5E in DCS has no trim effects anymore but all the other modules seem fine?

August•1/31/25, 10:05 PM

I've managed to get my settings dialed in after a couple of test flights. 2 questions remain. How do I disconnect the standard spring effect from the spring dynamic effect? I would like to have no spring effect at all when standing still and as air speed increases have more and more spring like effect. Second question, how do I decrease the inertia effect time. Now it feels a bit sluggish. I would like to have the inertia kick immediately when stopping the stick from moving. Now there is a bit of a delay, when the stick is stopped until I feel the 'inertia kick/effect.

NNemisis Wolf My issue was that for the first week I had it, I was just hitting the Big Red Bu...

Number481•1/31/25, 11:48 PM

I only have the FC F5, and while it has bindings for rudder trim, they don’t seem to do anything. IDK about the full fidelity versions.

The pedal trim feature in TelemFFB reacts to the physical movement of the control surface. If that doesn’t move with rudder trim, it won’t work.

NNumber481 I only have the FC F5, and while it has bindings for rudder trim, they don’t see...

Nemisis Wolf•1/31/25, 11:58 PM

HI I can confirm that the F-5E trim both stick and Rudder used to work fully without issues, The Stick and Rudders would both move and react to trim inputs. But since ED updated DCS on the 24th of Dec I could not fly as they buggered something up for me! They seem to have fixed the issue I had with the latest update but now the F-5E cannot be trimmed out and is basically unflyable with the Rhino! All other modules that I have tried and I have most seem to be absolutely fine!

GGTOfire Good to know, thanks! And yeah I've definitely enjoyed a few beautiful moments w...

OldmateHC•2/1/25, 2:07 AM

Hit the awacs up and start getting a soak before you taxi to help SA

NNumber481 I only have the FC F5, and while it has bindings for rudder trim, they don’t see...

Nemisis Wolf•2/1/25, 10:15 AM

Well I don't know how I fixed it but ALL is well in F-5E Tiger II world!!

I reset the configurator to factory defaults and used the standard config file for the F-5E and the Trim is now working properly!

TTheAmazinGreat Have you tried cycling the e-stop?

Ourorborus•2/1/25, 11:34 AM

It was a good suggestion but having just tried it, it makes the game lose the whole stick. Going to give "autohotkey" a go

Padinn•2/1/25, 11:59 PM

Has anyone found a reliable way to get the cog covers to stick? Mine unfortunately keeps coming off. Tried a couple things so far but no luck

PPadinn Has anyone found a reliable way to get the cog covers to stick? Mine unfortunate...

walmis•2/2/25, 12:49 PM

Hmm, did you try a foam double sided tape?

55earchkaine hi, does anybody know how to set my VKB grip as default device in the Rhino Inpu...

Jaeger•2/2/25, 12:57 PM

This is still a pain in the butt. Is there any help to get it back to remember it's last setting?

Wwalmis Hmm, did you try a foam double sided tape?

Padinn•2/2/25, 1:48 PM

Been using a silicone one but I'll give foam a try

PPadinn Been using a silicone one but I'll give foam a try

Number481•2/2/25, 1:51 PM

I cut up some command strips. Never moved until I took them off.

Leodis•2/2/25, 7:55 PM

Hey all, I got 1h40m into a DCS campaign mission yesterday when my Rhino suddenly disconnected in the middle of a Case III approach. The stick went limp and there were no inputs reaching the game. I pressed and reset the emergency stop and unplugged and reconnected the USB cable on the base and it reconnected, but there was no longer any FFB. I restarted TelemFFB and got the periodic effects back, but there were no spring forces. I managed to trap, but wondering if there's anything else I can do to recover from a disconnect and restore all forces in the future. I'm worried about this happening during a multiplayer squadron mission as those often run over 2 hours. Thanks!

LLeodis Hey all, I got 1h40m into a DCS campaign mission yesterday when my Rhino suddenl...

Touch_Of_Legend•2/2/25, 8:06 PM

I have never had an issue but someone the other day said that they experienced “random FFB disconnects” similar to what you’re describing.

The issue and fix for this person was Vjoy or joystick gremlin virtual joystick? (One of those) was causing a dual input.

To fix the issue they just disabled “ FFB” check box in the virtual joystick or the Vjoy.

Maybe it was under the support channel so see if you can find it AND double check yourself (if your running any virtual joystick) that the “FFB” is unchecked.

That’s the only thing recently I’ve seen so maybe that’s a start for troubleshooting

Leodis•2/2/25, 8:14 PM

Thanks, I appreciate the response. I am using vJoy and Joystick Gremlin, but I just double checked and "Enable Effects" is already disabled in vJoy. I don't see any FFB related options in Joystick Gremlin. I will search the channel for the history though. Thanks again.

TTouch_Of_Legend I have never had an issue but someone the other day said that they experienced “...

Rocco Thamanoidis•2/2/25, 8:47 PM

I use vjoy for my pedals, but ffb effects are all disabled there. Two weeks ago I thought I found the solution, in disabling MSFS support in TelemFFB ... then one full week no ffb loss/disconnect. But this week it returned. What a nasty "bug".

ono•2/3/25, 11:37 AM

Hello a question: if I set the spring to 100% in the ffb configurator, then the maximum stroke distance in y is only half as long. What am I doing wrong or how can I adjust this?

When I send spring off, it's 100% of the total length again

Oono Hello a question: if I set the spring to 100% in the ffb configurator, then the ...

TheAmazinGreat•2/3/25, 11:41 AM

Check description of force comp settings. Down by the calibration values. It is shorter due to flex in the system.

Jaeger•2/3/25, 11:44 AM

For me it's a hid disconnect that gets DCS to stop sending FFB effects (spring). Only a DCS restart fixes that. In my case it is PointCTRL, which I painstakingly have to make sure not to reset while dcs is running.

ono•2/3/25, 12:07 PM

Hardware trim in ffb or the trim in the applications? What is better?

Fr4Ged•2/3/25, 12:14 PM

Applications. Only use the hardware trim as last resort imo.
E.g. the DCS Apache hates being used without its trim. Lol

FFr4Ged Applications. Only use the hardware trim as last resort imo. E.g. the DCS Apache...

ono•2/3/25, 1:12 PM

Dentedend10•2/3/25, 9:16 PM

Hi. My Rhino was working fine yesterday. Today when I turn on the Y axis does not work. I get the error code Faulty Encoder 12C

Dentedend10•2/3/25, 9:16 PM

Please someone help

JJaeger For me it's a hid disconnect that gets DCS to stop sending FFB effects (spring)....

*NOB*Aries•2/4/25, 8:13 AM

PointCTRL can take down even my VR sometimes if it's USB connection goes in and out...

*NOB*Aries•2/4/25, 8:14 AM

*NOB*Aries•2/4/25, 8:16 AM

my USB port holder casing just broke... where could I get STL file to re-print it?

walmis•2/4/25, 8:22 AM

@NOBAries here you go

usb-flange.zip22.35KB

Jaeger•2/4/25, 8:26 AM

Great, I killed mine as well, glued it together for the time being. Price too pay for a removable setup, I guess.

*NOB*Aries•2/4/25, 9:58 AM

it's the cables... I have to rotate base for 180 and flip pitch axis... cause this way me or my son always nudge the cables acidentally...

**NOB*Aries it's the cables... I have to rotate base for 180 and flip pitch axis... cause th...

kaltokri•2/4/25, 10:10 AM

You can also buy 90° angled adapters/cables.

Jimmy•2/4/25, 11:05 AM

Could I request views for and against mounting the Rhino on a LONG Monstertech mount on an IKEA desk, with vibration settings turned down very low to avoid it shaking the desk to bits - thanks.

(NB: My personal interest is in the Rhinos realistic trimming and aerofoil pressure NOT sensations of gear or airbrake travelling etc.)

JJimmy Could I request views for and against mounting the Rhino on a LONG Monstertech m...

Blackrat•2/4/25, 11:09 AM

You can turn all effects down or even select which ones you want and customise each one, lets face it you can always buy a stronger desk

Festr ᶬꞙƨ•2/4/25, 12:15 PM

Good to know, thanks! And yeah I've definitely enjoyed a few beautiful moments when I had essentiall

Similar Threads

Similar Threads

Similar Threads