LeoManola
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/30/2025 in #fix-my-printer
How to enable nozzle wipe
Yes, saved. Still not wiping
5 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/30/2025 in #fix-my-printer
Large nozzle extrusion issue
Thank you, I will give that a try
6 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/30/2025 in #fix-my-printer
Large nozzle extrusion issue
Searching online and found people solve the same issue by increasing their max_extrude_cross_section and/or max_extrude_only_distance values in the printer.cfg but I do not have either in my extruder section
6 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/30/2025 in #fix-my-printer
Large nozzle extrusion issue
Turned on Relative Extrusion which did not resolve
6 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/26/2025 in #fix-my-printer
Beacon lower than nozzle
I had to redo my mesh after adding the UHF extender, that was the issue. Working now
11 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/26/2025 in #fix-my-printer
Beacon lower than nozzle
11 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/26/2025 in #fix-my-printer
Beacon lower than nozzle
11 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/21/2025 in #fix-my-printer
Gantry Twist very high
6 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/20/2025 in #fix-my-printer
Electronics fan not turning on
I moved the connector to the 3rd from bottom plug shown in the most recent photo I sent and the fan is working now.
13 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/20/2025 in #fix-my-printer
Electronics fan not turning on
I am using Ratos. I have not seen any wiring diagrams in the configurator, can you point me towards those?
13 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/20/2025 in #fix-my-printer
Electronics fan not turning on
13 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/20/2025 in #fix-my-printer
Electronics fan not turning on
13 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/20/2025 in #fix-my-printer
Electronics fan not turning on
13 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/14/2025 in #fix-my-printer
Bed Heater Wiring Confusion
Got it, thank you!
18 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/14/2025 in #fix-my-printer
Bed Heater Wiring Confusion
18 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/14/2025 in #fix-my-printer
Bed Heater Wiring Confusion
Does it matter which goes where?
18 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/14/2025 in #fix-my-printer
Bed Heater Wiring Confusion
So I am looking at the two yellow wires coming from the bed heater in the schematic I posted? Left and right is correct in that and should be followed?
18 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/14/2025 in #fix-my-printer
Bed Heater Wiring Confusion
Are there instructions on that anywhere?
18 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/14/2025 in #fix-my-printer
Bed Heater Wiring Confusion
The ones in my photo of the bed heater
18 replies
RRCRat Rig Community [Unofficial]
•Created by LeoManola on 5/14/2025 in #fix-my-printer
Bed Heater Wiring Confusion
So where do the two white wires go?
18 replies