Catweazle (Stefan)
RRCRat Rig Community [Unofficial]
•Created by Catweazle (Stefan) on 5/13/2025 in #ratos-support
VAOC calibration
I don't know how, but suddenly it worked. My first print (skew calibration) is running!!!
6 replies
RRCRat Rig Community [Unofficial]
•Created by Catweazle (Stefan) on 5/13/2025 in #ratos-support
VAOC calibration
Now I can't save the changes and select T1
6 replies
RRCRat Rig Community [Unofficial]
•Created by Catweazle (Stefan) on 5/13/2025 in #ratos-support
VAOC calibration
I found the error, the changes I made in the printer config had dissapeared.
6 replies
RRCRat Rig Community [Unofficial]
•Created by Catweazle (Stefan) on 5/11/2025 in #ratos-support
**RatOS Configuration Repository**
👍
I didn't close the electronics box yet so that the fan doesn't work yet. So I will do this work first ...
16 replies
RRCRat Rig Community [Unofficial]
•Created by Catweazle (Stefan) on 5/11/2025 in #ratos-support
**RatOS Configuration Repository**
I didn't have the problem before, it looks as if the motors get too high current, may be since i changed to "performance mode"
16 replies
RRCRat Rig Community [Unofficial]
•Created by Catweazle (Stefan) on 5/11/2025 in #ratos-support
**RatOS Configuration Repository**
16 replies
RRCRat Rig Community [Unofficial]
•Created by Catweazle (Stefan) on 5/11/2025 in #ratos-support
**RatOS Configuration Repository**
I don't know wether it has anything to do with your solution, but now I have a new problem, that I didn't have before:
16 replies
RRCRat Rig Community [Unofficial]
•Created by Catweazle (Stefan) on 5/11/2025 in #ratos-support
**RatOS Configuration Repository**
Thank You, whatever it did, it worked fine 😉
16 replies
RRCRat Rig Community [Unofficial]
•Created by Catweazle (Stefan) on 5/11/2025 in #ratos-support
**RatOS Configuration Repository**
could you please write a little bit more what I should do? I'm not very experienced with klipper.
I tried to connect with putty, but I don't no Login-name and password.
16 replies
RRCRat Rig Community [Unofficial]
•Created by Catweazle (Stefan) on 5/11/2025 in #fix-my-printer
Finish the Commissioning guide
15 replies
RRCRat Rig Community [Unofficial]
•Created by Catweazle (Stefan) on 5/11/2025 in #fix-my-printer
Finish the Commissioning guide
15 replies
RRCRat Rig Community [Unofficial]
•Created by Catweazle (Stefan) on 5/11/2025 in #fix-my-printer
Finish the Commissioning guide
15 replies
RRCRat Rig Community [Unofficial]
•Created by Catweazle (Stefan) on 5/11/2025 in #fix-my-printer
Finish the Commissioning guide
in which cfg can I find this option? I can't find it - I find it just in the klippy.log
15 replies
RRCRat Rig Community [Unofficial]
•Created by Catweazle (Stefan) on 5/11/2025 in #fix-my-printer
Finish the Commissioning guide
15 replies
RRCRat Rig Community [Unofficial]
•Created by Catweazle (Stefan) on 5/11/2025 in #fix-my-printer
Finish the Commissioning guide
... as far as I could see
15 replies
RRCRat Rig Community [Unofficial]
•Created by Catweazle (Stefan) on 5/11/2025 in #fix-my-printer
Finish the Commissioning guide
I did the PID for both hotends an everything worked ok
15 replies
RRCRat Rig Community [Unofficial]
•Created by Catweazle (Stefan) on 5/11/2025 in #fix-my-printer
Finish the Commissioning guide
I found how to save the changes but still don't understand the warning
15 replies