Vase mode seam?
I am printing some chrismas ornaments in vase mode. I am not able to eliminate what looks like a seam. Attached are some pictures of the orca slicer view and the actual print. They both show a seam. When printing, the printer does not stop or slow down at any position. I have double checked that I have "spiral vase" checked. This defect looks more pronounced in areas where the slope gradient is large. Any suggestions?
First Layer -> Future Layer Issues
Hey all, I'm having some issues with my first layers that are then causing scraping & gap issues in my later layers. For some quick background info, I'm just coming off of diagnosing & fixing my bed mesh issues (https://discord.com/channels/582187371529764864/1182847451049250917) and believe that my underlying problems were caused by a slight warp in my bed which I though I was able to remedy. The problem now however is that I consistently see small gaps in the front and right edges of my print'...
Manual Input Shaper Calibration Print Problems
I am following the tuning guide from RatOS documentation to calibrate a V-core 3.1 400mm printer.
Using the Manual Input Shaper instructions from the Klipper documentation here;
https://www.klipper3d.org/Resonance_Compensation.html...
calibration confusion
Well i try to make a cable Container with some rotating parts but i have some issues that the parts Always fuze together.
I did try temp Towers
Also retraction Towers and Stuff Like this and the result for the calibration cubes are also OK but with a hole because the lead screw could Take some cleaning (atleast i think so)
But i still get horrible tolerances ...
ABS bed adhesion issues
Does anybody have an idea, why I have these intermittent adhesion problems with my print sheet?
The Filament is Flashforge ABS and the sheet is the one that came with the VC3.
I have tried cleaning it thoroughly (soap, water, IPA) and have tweaked my Z height and bed temps to no avail.
Could the PEI just be end of life/damaged at that location?
Does anybody know of good print sheets for ABS use?...
weird extrusion
As you can see on both calibration cubes the lines seem to be weird at a certain height.
Weird First Layer Anomaly
I've been having this issue for a while and cant put my finger on it. uses adaptive bed mesh and prints brim and boundaries fine but as it does the infill it slowly get closer to the bed to the point of not extruding anything?
Any help would be much appreciated, Caleb...
Sparse infill speed modifier not working on certain parts
Quite some time ago i posted this issue on the superlicer github. It has not gotten any attention so i am posting it here wondering if someone has experience with these more advanced settings. This modifier seem to work sometimes on other parts but cannot figure out why.
https://github.com/supermerill/SuperSlicer/issues/3849...
top surface pattern
Getting a ripple effect on the top surface almost like the layers below are coming threw.
I have seen this on my other printers on the second layer only. Seems to keep stacking on my second printer. Both are running same extruder setup etc.
1.0mm nozzle and 0.4lh...
Failed print
Last few prints before this came out good, extrudes fine, what could have happened? Bondtech LGX Lite + Phaetus Rapido HF.
I noticed when doing a cold pull after this print that the hotend fan doesnt sound very healthy....
1 x 5015 not enough right.
i printed a benchy and while my tuning is going the right direction. i still get a fail here and its def part cooling right ?
New Printer First Layer Under Extrusion?
Just setup a new VCore 3.1 running RatOS, Orbitor 2.0, Revo Micro (with 0.6 nozzle), OrcaSlicer and getting what looks to me like under extrusion. This is my first Klipper based system, and while it was great to be able to pull in the pre canned configs for most of my parts, it feels odd to me that I didn't have to do things like tune extrusion steps or extrusion length like I'm used haha.
I played with the "Fine tune" menu taking extrusion up to +106% but didn't see any improvement, I then backed off the Z offset which also didnt show improvement (that's where the print started to fail). This is my first printer using PEI so I'm a bit scared to push the offset lower given the paper test during PROBE_CALIBRATE felt pretty good. Any ideas, what nobs should I be turning in Klipper?...
V-minion top layer ridges
Hey, maybe you know what is causing these ridges on the top layer? It seems less noticeable with certain plastics, but it generally always appears.
V-minion, Eva3, Dragonfly BMO, bondtech lite, 4028fan....
strange lines of low flow
Can anyone explain these lines in my prints? It’s like the flow rate drops.
Prusa galaxy pla
Orbiter 2.0
Phaetus dragon BMO...
