Layer lines more visible in X axis
I noticed when printing a PA tower that for some reason the Y axis sides looked better than the X axis. It seems to have lines popping. Could this be atributed to the idlers on the xy joiners? When printer moves on Y those stay stationary
overextrusion at beginning of print
Hello,
as you can see in the pictures, I am having issues with overextrusion at the beginning of my prints. Do you have any ideas which setting might cause this?...
Blob on perimeter start after Gap Fill
I have been tackling a issue for some days now, and i was able to pin point in what exact situation it occurs.
Every time there is an extrusion for a Gap fill just before a perimeter start, i get a blob on the start of the perimeter that also translates most of the time to a unveven line of extrusion.
I have tried this with SuperSlicer (2.4.58.5 and 2.5.59.0), tried with PrusaSlicer also....
How do I improve from this test?
I've printed this tuning test on my VCore 3.1 400 with a 0.6mm nozzle, in PLA at 215c through a Rapido HF/Orbiter 2, 100mm/s & 4k acceleration external perimeters. PA set to 0.045 and IS active in RRF (yeah not using Klipper but RRF on Duet 6HC). Layer height 0.2mm.
The print took roughly 1h, 40min.
I printed a Benchy with the same settings that looks pretty good, some ringing but overall better than this larger test. I understand this model was (probably) designed for a 0.4mm nozzle so the fine details will suffer.
...
overextruded solid layers with Extrudr Durapro ABS,
I am only having issues with ABS, PLA, PCTG etc work without such issues.
I am having issues with the Extrudr ABS:
solid layers get overextruded altough I did calibrate the flow rate to match the extrusion with of single perimeters exactly. ...
lifting first layer
First layer lifts as it's put down. If i can make it up a couple layers then no problem.
Pla
Bed @70. Nozzle @ 200...
Underextrusion at layer change when printing at high speeds.
I'm running into issues when printing at higher speeds on my VC3 400. The issue is independent of the used filament manufacturer. I currently print PETG that's been in a food dehydrator for 24hrs, so probably as dry as you can get.
Setup is a NF-Crazy (Mosquito-Clone) with a Volcano-Style Block (Like the Volcomosq, but also by Mellow). The nozzle is a CHT-Clone 0.6mm with a CNC Volcano nozzle adapter. The setup itself is quite capable in the sense that you can melt a shitton of material at once, but i get really ugly layer changes:...
New Printer-Z banding?
This voron cube is the first print off of the bed of Vcore 3.1 build sliced in prusa slicer printed at 195℃ excellent adhesion but how do I get rid of this zbanding or is it something else .I will be doing resonance calibration pretty soon and tightening the belt and I know that I need to increase the cooling as well
Getting rid of an ugly seam
Hi guys,
I am tinkering around for a while, but i can't get rid of that ugly seam.
A few facts:...
ASA first print
This looks like over extrusion. But in some places it looks fine.
Seems to be blobby around where layers start/end, and sharp corners.
By the way this isn't a Ratrig. I'm trying to get some acceptable settings to print parts for my new Ratrig on an old printer....
Large ABS Print Issues
Good Morning! I was hoping to get some advice on an issue I've been having with a print. The machine is new, and does great on small parts, but has failed every time I've tried to print this larger one. The supports/infill extrusions have poor layer adhesion and on occasion exhibit a "pulsing" behavior. Overhangs as well (long sides of print). It can print a benchy fine, and other test prints fine, it's just the large prints. First layer adhesion is fantastic with no warping and good extrusion adhesion between lines.
Info about the setup:
- Nozzle 0.8, layer height 0.45
- ABS Hatchbox Filament...
BAD Z Artifacts on new V Minion
Hello all. I have really bad Z Artifacts on a newly build V Minion. I've checked the lead screw a couple times and got it as square to the frame and as straight as possible (even used some 3D printed tools) and it doesnt seem wiggle at all when going from Z0 to Z180. Halp!
