RRC

Rat Rig Community [Unofficial]

The #1 unofficial Rat Rig Community on Discord!

Join

RRC

Rat Rig Community [Unofficial]

The #1 unofficial Rat Rig Community on Discord!

Join

ratos-support

fix-my-print

fix-my-printer

fix-my-resonance

fix-my-mesh

german-support

John Vybiral

3/9/2023

RatOS v2.0.0... now unable to join network "RatOS"

Please help? Downloaded 2023-03-03-RatOS-v2.0.0-raspberry-rpi64.img.xz from GitHub. Flashed to micro SD card using balenaEtcher, as I did before with V1.2.4. No problems. 4 different computers (2 Windows 10, 2 iOS) all "see" RatOS, but all 4 say, "Unable to join network "RatOS". Please, what am I doing wrong?...

ugly-tan

3/9/2023

octopus v1.1 bootloader

Does anyone has the original bootloader for octopus v1.1? Thanks!...

magic-amber

3/8/2023

M106 nor working while printing

Hi Guys , Strange behavior. when the printer is not printing changing the part fan with M106 or the slider in the GUI - changes the fan speed. but while printing , the fan is off and not responsive for M106 or changes in the slider in the GUI ... ...

Grimstod

3/7/2023

Octopus 1.1 firworks

I will say the new RatOS is much easier to fallow on settup. But i clearly still have an electrical problem somewhere.

genius23pl

3/6/2023

Burning hotend - Rapido

HELP. I've gone completely dumb. at first I have a symptom that the rapido does not heat up above 220C degrees and now I have the impression that it is heated to the max, i.e. up to 350C because the filament is on fire. it is connected to the EBB36 can bus and the thermistor is PT1000 ( two lines)...

ugly-tan

3/5/2023

extrusion gap

should I ignore these gaps? I have used an engineering square to adjust the frame and I have these gaps. Thanks...

Bot Sculptor

3/5/2023

How to update firmware on Octopus 429?

I've been printing successfully for a while, and then after updated everything through the Update Manager, the bed heater stopped working and shuts down the printer after taking too long. Did a full diagnostic of all wires, connectors, resistance, etc and everything is solid and the SSR is getting power. My best guess was that I needed to update the firmware on my Octopus Pro 429, but all the links for how to do this lead to a dead page.

HeineMau

3/5/2023

XY Stepper error

On my RatRig Vcore3-500 I sometimes get:

TMC 'stepper_y' reports error: DRV_STATUS: c0130010 s2vsa=1(LowSideShort_A!) cs_actual=19 stealth=1 stst=1 Once the underlying issue is corrected, use the "FIRMWARE_RESTART" command to reset the firmware, reload the config, and restart the host software. Printer is shutdown

Sometimes it appears shortly after powering on the printer, sometimes after an hour of printing, sometimes not at all. (typ. print time 0.5-2h) Sometimes it reports the short on channel A, sometimes on channel B. But always 'stepper_y'. The cables are factory crimped and are looking perfectly fine....

SimonSolar2C

3/5/2023

XY axis scale wrong

I can’t find solution on how to adjust nor do I understand the cause. Except maybe belts stretched.

foreign-sapphire

3/4/2023

cant connect to klipper

Hello Everyone. First of all. My printer has been just fine with printing and everything. Just noticed a lot of updates. So started updating and now I can't connect to Klipper. Can anyone help me.

genius23pl

3/4/2023

Z_TILT_ADJUST - Impossible to complete.

Hello. since 5 hours I can't handle both with Z_TILT_ADJUST I checked everything I know, even changed all possible motor connections to Z, Z1, Z2, LMR RML LRM...

Z_Tilt_adujust.txt

vhaude

3/4/2023

Rescue print after Power outage

Hey, so around 40h into a 60h print job we had a power outage. I plan to resume printing but am unsure if my planned way is the best possible and would like to here a second or third opinion. I plan to do it the following way: 1. Restore power ...

genius23pl

3/4/2023

Rapido UHF can 't reach more than 226 °C

Another day another problem I have a Rapido Plus UHF with a heater up to 350°C, connected to the EBB36 board. When trying to do pit tuning the maximum temperature as it gets is 226°C then to the message "pid_calibrate interrupted". Up to 180 ° C, the heating slides like crazy but drops drastically. ...

harsh-harlequin

3/4/2023

G28 Home all behavior

I have sensorless homing setup for X and Y which seem to work independently if I home X and home Y. However, if I try to G28 home all, then it homes X correctly and the does not seem to home Y, it goes to the middle and then the back of the machine. I had to change a setting in the config to get it to home to the front, maybe I missed another step? I had to adjust "position_endstop: 0 # 200mm printer" for Stepper Y...it was originally at 200 for my size build and changing it to 0 seems to have...

vhaude

3/3/2023

Rescue timelapse after Power failure

Hi, I didn't know where to post this so please feel free to move this thread if it belongs somewhere else. I just did a 60+ hour print and there was a power out in our building at around 40h into the print. I will be able to recover the print but also want to safe the time-lapse pictures I did with the moonraker time-lapse plugin. The problem is I selected autorender before starting the print. As it didn't finish there is no completed print and hence no autorendered time-lapse file. ...

adverse-sapphire

3/2/2023

Extruder E-Steps Calibration

I've recently completed a VCore 3.1 and I'm trying to go through some basic calibration steps and I'm new to RatOS/Mainsail. I tried entering the appropriate gcode commands to the console but they weren't recognized. How can I go about this calibration? Is there some other terminal/console available for direct gcode entry, or does RatOS/Mainsail have its own functions for extruder calibration?

genius23pl

3/2/2023

Probe triggered prior to movement

Hello. I have a problem this time with Z_TILT_ADJUST the printer is easily based on 3 axes x, y, z but when try to make Z_TILT_ADJUST head goes to one corner and stops after I have a message...

conscious-sapphire

3/2/2023

Belt path out of whack

So my belts are grinding, I have a picture of the aftermath and a small video. Does anyone have any tips on what could be wrong? Do you need any different views? https://youtu.be/78kLiacQCHU - short video of the problem....

genius23pl

2/28/2023

pin PC7 is an alias for z1_uart_pin

I had to change some stepper settings and after changing the appropriate parameters I have this message Klipper reports: ERROR ...

ugly-tan

2/28/2023

TMC 2209 Driver Error

Hey guys, I keep getting an OverTemp warning and eventually error on my stepper drivers. No single driver is reporting this it's been 3 different ones so far. However, I don't even think these drivers are getting very hot. This was the line in Klipper log during shutdown: Stats 153574.3: gcodein=0 mcu: mcu_awake=0.017 mcu_task_avg=0.000014 mcu_task_stddev=0.000012 bytes_write=108823330 bytes_read=24367929 bytes_retransmit=9 bytes_invalid=0 send_seq=2151521 receive_seq=2151521 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=8 stalled_bytes=4166 freq=180001796 toolboard: mcu_awake=0.026 mcu_task_avg=0.000047 mcu_task_stddev=0.000049 bytes_write=27696987 bytes_read=9669628 bytes_retransmit=9 bytes_invalid=0 send_seq=594299 receive_seq=594299 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=30 stalled_bytes=0 freq=63999318 adj=63998746 Octopus: temp=22.0 raspberry_pi: temp=30.0 sd_pos=96898247 heater_bed: target=110 temp=110.0 pwm=0.432 toolboard: temp=61.1 sysload=0.23 cputime=18677.546 memavail=574960 print_time=153159.602 buffer_time=2.221 print_stall=4 extruder: target=260 temp=259.7 pwm=0.451 TMC 'stepper_z2' reports DRV_STATUS: c01f0f03 otpw=1(OvertempWarning!) ot=1(OvertempError!) t120=1 t143=1 t150=1 t157=1 cs_actual=31 stealth=1 stst=1 Transition to shutdown state: TMC 'stepper_z2' reports error: DRV_STATUS: c01f0f03 otpw=1(OvertempWarning!) ot=1(OvertempError!) t120=1 t143=1 t150=1 t157=1 cs_actual=31 stealth=1 stst=1...

Previous Next

Gaming

Programming

Rat Rig Community [Unofficial]

The #1 unofficial Rat Rig Community on Discord!

Rat Rig Community [Unofficial]

The #1 unofficial Rat Rig Community on Discord!