Saddle shaped mesh
My mesh looks like a saddle. It's an upside-down uon the x, and a rightside-up u on the y. Is this a sign of a warped x-gantry? This is for a v-core3 500.
V-Core 3 400 mesh, good enough?
I've managed to get this far, should I take it any further? My biggest concern is the recessed area in the right rear. Range is .206mm (-.130 to .076)
Tolerances of 500x500 bed ?
what are the tolerances of a 500 bed?
Is it true that this is because the y-axis on the right side is not correct?
thanks in advance!!!...
Saddle shape mesh (V-Core 3.1 500mm)
I started with a big dip at "D" after following the advice from the video I ended up with a saddle shape. It looks like the bed is bowing down at the unsupported corners.
The total range is 0.390mm when heated to 70C
I verified that the Y rails are parallel to eachother and they were screwed in the correct order.
Any suggestions on how could I improve this?...
Bed mesh doesn't seem to apply
So i have a bed mesh deviation of 0.27 on a V3-500 using a Beacon. I thought that'd be enough to get a perfect first layer. What I'm seeing is that the from about 300+ on the x axis up there is a noticeable gap under the nozzle and isn't close enough to get any adhesion. I've been in the process of squaring up the frame and with a 0.27 variance, it's probably as good as it gets. Any idea what would cause an irregular mesh application?
Huge Bed Dip! Help!
V-Core 3.1 500. Mesh made with Beacon while bed was heated to 80C.
Additionally I have an enclosure 2.0. I am not sure how I should be adjusting extrusions, given that vertical extrusions are connected to multiple horizontal extrusions....
Mesh Suggestions
Hello there. I have a Vcore 3.1 500 with a beacon probe. This is my mesh with the bed heated. Does anyone have any suggestions on improvement, or should I just move on?
Trouble getting my frame squared (V-Core 3.0 300mm)
I tried to square my frame according to the guide but no matter what i do the resulting mesh isn´t changing at all. I run z-tilt after every change to the frame. I did this over 10 time now (didn´t save the older meshes) still always with the same result. The odd thing for me is that the frame is definitely moving.
I would be grateful for any tips....
hump in the middle of the bed
Was doing some adjusting as shown in the frame calibration video and there now appears to be a large hump in the center of the bed
V-Core 3.1 300x300, could use some pointers.
I'm am having problems with layer 1 adhesion, which led me to checking the mesh. The resulting mesh kinda stumped me - hope you guys can give me some pointers:
Is this OK?
[V-Minion] My print seems to stick only on specific areas. It sticks well in the middle however.
Thanks for any and all help!...
2nd Hand Printer with paper underneath?
Hello everyone. I recived a broken 500mm ratrig 3.1 as a gift. After some lovely people in the fix my printer channel helped me get it going again i am now trying to level the bed. Upon Closer inspection there appears to be many paper shims between the PEI and the magnetic pad. After Removing the shims this is my mesh result. I will send a picture of the mesh before I removed the paper. I do not beleive this is a common practice? I assume the possibility frame isnt square and they did this as a...
Bad first layer, mesh not compensating as it should
So ive had this problem forma while and yesturday i tried to increase the mesh points to 20x20 just to maybe get a more accurate mesh, but no.. here some pictures and a video so u can see what it looks like
after shiming right rail no Differenc
Hi,
I Was trying to get by bed better. So i try to shim the right rail.
I put shimtape between the rail and the profile. Maximum was 0.4 on the right back corner. So normaly i would say that must lift up the rear right corner in the mesh. But it doesnt happen. If i compare it with the normal one.(Without shim) it looks better i think. But the Differenc arr so small. Can anyone explain it?
Generaly i interested to know if this mesh ist bad or good for a 300? ...
Mesh got worse after installing the enclosure
So, I've had some issues getting my frame (vcore 3.1 400) to be level and square, and the mesh had around 0.17mm of variance, which was fine by me
However, After adding the enclosure panels, this is what I get (Image 1) and my old mesh (Image 2).
It seems like the bed is sagging heavily at the back, non supported corners, but I don't see how this can be caused by the enclosure....
